Sony WX-4500X Installation guide
- Category
- Car video systems
- Type
- Installation guide
Sony WX-4500X: Experience superior in-car audio with this versatile device. Connect your CD/MD changer via the BUS AUDIO IN port and control it seamlessly with the BUS CONTROL IN. Enhance your music with an external amplifier, subwoofer, or active speakers. Personalize your listening experience with the source selector (not included) and connect your phone or other devices via the interface cable. Enjoy clear sound and stay connected on the road.
Sony WX-4500X: Experience superior in-car audio with this versatile device. Connect your CD/MD changer via the BUS AUDIO IN port and control it seamlessly with the BUS CONTROL IN. Enhance your music with an external amplifier, subwoofer, or active speakers. Personalize your listening experience with the source selector (not included) and connect your phone or other devices via the interface cable. Enjoy clear sound and stay connected on the road.
Sony Corporation © 2001 Printed in Japan
WX-4500X
Equipment used in illustrations (not supplied)
Cautions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all ground wires to a common ground
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
•The use of optical instruments with this
product will increase eye hazard.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Connection example (2)
Tip (2-B-
)
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
When insert the each connector, be sure to insert
it securely, as vibration through driving may
cause a poor connection.
1To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
1
2
B
12
× 6
3
4
× 6
Power amplifier
CD/MD changer
Front speaker
Rear speaker
Source selector*
*
*
BUS CONTROL IN
A
Installation/Connections
Changer Control
Audio Master
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the interface cable of a car telephone
5To a car’s illumination feed
Be sure to connect the black ground lead to it
first.
6To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground lead to it
first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
7To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it
first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies
+12 V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
• A power antenna without relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
Active subwoofer Rotary commander RM-X4S
SUBWOOFER OUT
(MONO)
*I-3-229-007-11*(1)
For NISSAN cars only
*not supplied
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Downloaded from: https://www.usersmanualguide.com/
MONO
L
R
MONO
SUB WOOFER BUS AUDIO
OUT IN
3
1
4
5
6
Blue
Red
Yellow
4
Black
Max. supply current 0.1 A
Fuse (10 A)
BUS AUDIO IN
AMP REM
ANT REM
BUS CONTROL IN
Light blue
Max. supply current 0.3 A
White
Gray
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Purple/black striped
Source selector*1
*1
*1
Left
Right
Left
Right
3
Blue/white striped
2
REMOTE IN
ATT
Supplied with the CD/MD changer
Supplied with XA-C30
SUBWOOFER OUT
(MONO)
RCA pin cord (not supplied)
Orange/white striped
7
ILLUMINATION
•
•
•
•
•
•
•
•
1
2
2
3
1
2
•
•
3
4
5
6
•
•
7
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
2
2
3
1
2
•
•
3
4
5
6
•
•
7
•
•
•
•
•
•
•
•
•
•
*1not supplied
*2Connect the Bus cable to its
terminal with the unit’s V mark
and the Bus cable’s v mark
aligned.
*1
*2
*1
*2
*2
Downloaded from: https://www.usersmanualguide.com/
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
Notes
• Use the screws 1 or 2 depending on the make of
car. When this unit is attached to a MITSUBISHI car,
use the supplied screws 2.
• To prevent malfunction, be sure to install using
brackets and the supplied screws 1 or 2.
• Do not apply excessive force to the buttons of the
unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on
the top of the unit.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
Reset button
When the installation and connections are
completed, be sure to press the reset button with
a ball-point pen, etc.
Note
When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
1 2
•1 2
2
•
1 2
•
•
•
(OFF)
(OFF)
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
Frequency select switch
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch on the left side of
the unit to the 10 k (200 k) position before
making connections.
After the frequency select switch is set, you
must press the reset button to reset the unit.
Mounting the unit in a Japanese
car (4)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
•
•
•
4
4ATOYOTA/MITSUBISHI
to dashboard/center console
Bracket
Bracket
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
Existing parts supplied with your car
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
SEEK/AMS
MD
CD
EQ7DSO
OFF
SCRL
SA
SOUND
MENU
DSPL
AT T
SOURCE
SEEK/AMS
MODE
Reset button
SEEK/AMS
MD
CD
EQ7DSO
OFF
SCRL
SA
SOUND
MENU
DSPL
AT T
SOURCE
SEEK/AMS
MODE
N
N
N
M
M
T
T
N
N
M
T
T
T
N
N
N
M
M
T
T
N
N
M
T
T
T
This illustration is for TOYOTA cars.
BNISSAN
Existing parts
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
Bracke
3
N
N
N
M
M
T
T
N
N
M
T
T
T
To set the frequency select switch, use a
pointed object, such as a ball-point pen, to
gently slide the switch.
N
N
N
M
M
T
T
N
N
M
T
T
T
Downloaded from: https://www.usersmanualguide.com/
1 2
•1 2
2
•
1 2
•
•
•
(OFF)
(OFF)
•
•
•
4
rd/center console
Bracket
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
SEEK/AMS
MD
CD
EQ7DSO
OFF
SCRL
SA
SOUND
MENU
DSPL
AT T
SOURCE
SEEK/AMS
MODE
N
N
N
M
M
T
T
N
N
M
T
T
T
BNISSAN
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
Bracket
Existing parts supplied with your car
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1 2
to dashboard/center console
Bracket
3
•
•
•
•
•
•
•
•
4
SEEK/AMS
MD
CD
EQ7DSO
OFF
SCRL
SA
SOUND
MENU
DSPL
AT T
SOURCE
SEEK/AMS
MODE
N
N
N
M
M
T
T
N
N
M
T
T
T
N
N
N
M
M
T
T
N
N
M
T
T
T
N
N
N
M
M
T
T
N
N
M
T
T
T
Downloaded from: https://www.usersmanualguide.com/
This file has been downloaded from:
www.UsersManualGuide.com
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
documentation manual, user maintenance, brochure, user reference, pdf manual
Downloaded from: https://www.usersmanualguide.com/
-
1
-
2
-
3
-
4
-
5
-
6
Sony WX-4500X Installation guide
- Category
- Car video systems
- Type
- Installation guide
Sony WX-4500X: Experience superior in-car audio with this versatile device. Connect your CD/MD changer via the BUS AUDIO IN port and control it seamlessly with the BUS CONTROL IN. Enhance your music with an external amplifier, subwoofer, or active speakers. Personalize your listening experience with the source selector (not included) and connect your phone or other devices via the interface cable. Enjoy clear sound and stay connected on the road.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Sony WX-4500X Installation guide
-
-
Sony CDX-MP70 User manual
-
Sony WX-C55 Installation guide
-
-
-
-
-
-