Sony WX-C570 Installation guide

Sony
Brand
Sony
Model
WX-C570
Category
Motorcycle Accessories
Type
Installation guide
Changer Control
Audio Master
Installation/Connections
Sony Corporation 1997 Printed in Japan
WX-C570
Parts for installation and connections
The numbers in the list are keyed to those in the instructions.
1
2
34
× 8
(incl. 2 reserve)
× 1
For NISSAN cars only
× 1
× 1
*I-3-859-835-21*(1)
Note for connecting
If there is alternator noise (a whining sound when raising engine speed), earth the this unit by
connecting it to a metal point of the car with the supplied chassis ground cord 4. Connect the
ground cord to the this unit with the screw to the back of this unit as shown in the illustration.
To metal point of the car
4
Fasten the screw to the
back of this unit
Notes
• Do not use excessive force on the buttons of the unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on top of the unit.
Installation
Precautions
•Do not tamper with the four holes on the upper surface of the unit. They are for tuner adjustments to
be done only by service technicians.
•Choose the installation location carefully so that the unit will not hamper the driver during driving.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct
sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
•Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
Mounting the unit in a Japanese car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your
Sony dealer.
When you mount the supplied bracket to this unit, use the supplied screws 1 from this unit and
mount to the appropriate mount holes for your vehicle: T (for TOYOTA), M (for MITSUBISHI) and N
(for NISSAN).
TOYOTA/MITSUBISHI
1 max. size
5 × 8 mm
to dashboard/center console
Bracket
1 max. size
5 × 8 mm
NISSAN
1 max. size
5 × 8 mm
to dashboard/center console
1 max. size
5 × 8 mm
Bracket
Note
To prevent malfunction, install only with the supplied screws 1.
Existing parts supplied to
your car
2
Existing parts supplied to
your car
T
N
T
M
N
M
T
N
M
N
T
N
T
This illustration for TOYOTA cars.
SONY WX C570 (E) 3 859 835 21(1
Connections
Caution
This unit is designed for negative ground 12 V DC operation only.
Before making connections, disconnect the ground terminal of the car battery to avoid short circuits.
Connect the yellow and red power input leads only after all other leads have been connected.
Be sure to connect the red power input lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
Run all ground wires to a common ground point.
Connect the yellow cord to a free car circuit rated higher than the unit’s fuse rating. If you connect
this unit in series with other stereo components, the car circuit they are connected to must be rated
higher than the sum of the individual component’s fuse rating. If there are no car circuits rated as
high as the unit’s fuse rating, connect the unit directly to the battery. If no car circuits are available
for connecting this unit, connect the unit to a car circuit rated higher than the unit’s fuse rating in
such a way that if the unit blows its fuse, no other circuits will be cut off.
The use of optical instruments with this product will increase eye hazard.
Reset button
When the installation and connections are over, be sure to press the reset button with a ballpoint pen
tc.
Reset button
Change the position with a jeweler’s screwdriver, etc.
f your car has no accessory position on the ignition key switch
— POWER SELECT switch
he illumination on the front panel is factory-set to be turned on even when the unit is not being
layed. However, this setting may cause some car battery wear if your car has no accessory position
n the ignition key switch. To avoid this battery wear, set the POWER SELECT switch located on
he bottom of the unit to the B position, then press the reset button. The illumination is reset to
tay off while the unit is not being played.
ote
he caution alarm for the front panel is not activated when the POWER SELECT switch is set to the B position.
Connection example
from car antenna
Power amplifier
BUS AUDIO IN BUS CONTROL IN
REMOTE IN
RCA pin cord (RC-63 (1 m), RC-64 (2 m)
or RC-65 (5 m)) (not supplied)
Rear speakers
Front speakers
RCA pin cord (not supplied) BUS cable (not supplied)
Rotary remote (RM-X2S)
(not supplied)
Blue/white striped
AMP REM
Blue
Max. supply current 0.3 A
Max. supply current 0.1 A
ANT REM
Red
Yellow
Black
Green
Purple
Gray
White
Left
Front speakers
Right
Left
Rear speakers
Right
to the +12 V power terminal which is energized in the accessory
position of the ignition key switch
Be sure to connect the black ground lead to it first.
Notes on the control leads
• The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner or when you activate the ATA
(Automatic Tuner Activation) Function.
• A power antenna without relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the
ignition key is turned off.
Fuse (10 A)
3
Power amplifier
to the +12 V power terminal which is energized at all times
Be sure to connect the black ground lead to it first.
to a metal point of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
CD/MD changer
To connect to AMP REMOTE IN of the optional power amplifier.
This connection is only for amplifiers. Connecting any other system may
damage the unit.
to the interface cable of a car telephone
Sky blue
TEL MUTE
Orange/white striped
to a car’s illumination signal
Be sure to connect the black ground to it first.
ILLUMINATION
to the power antenna control lead or power supply lead of antenna
booster amplifier
<Note> In case of without power antenna, or antenna booster, not
necessary to connect this lead.
LINE OUT
FRONT
LINE OUT REAR
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities. Otherwise, the speakers
may be damaged.
• Do not connect the terminals of the speaker system to the car chassis, and do not connect the terminals of the right
speaker with those of the left speaker.
• Do not attempt to connect the speakers in parallel.
• Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so may damage
the active speakers. Therefore, be sure to connect passive speakers to these terminals.
Connection diagram
or connecting two or more changers, the source selector XA-C30 (optional) and the BUS cable RC-61
1 m) or RC-62 (2 m) (optional) are necessary.
Example 2
Example 1
Power amplifier
Power amplifier
WX-C570
LINE OUT
REAR
BUS
AUDIO IN
BUS
CONTROL IN
Rear
speakers
Front
speakers
CD/MD changer
CD/MD changer
Source selector
Rear
speakers
Front
speakers
WX-C570
BUS CONTROL IN
BUS AUDIO IN
CD/MD changer
LINE OUT
FRONT
  • Page 1 1
  • Page 2 2

Sony WX-C570 Installation guide

Sony
Brand
Sony
Model
WX-C570
Category
Motorcycle Accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents