Output Relay Rating
Max
Voltage Current
30VDC/125VAC 3A (per relay)
Function Description
NO/NC
Jumper
Position
Status Condition
JP1NO
PIN 1 short to PIN 5
Activated on UPS Fault
(Inverter Fault / DC Bus Fault / Over Temperature
/ Bat Test Fail / Bat Over Charge / Fan Error)
T8 short to T9/T10
JP1NC
PIN 1 open to PIN 5
T8 open to T9/T10
JP2NO
PIN 2 short to PIN 5
Activated on Summary alarm
(Inverter Fault / Output Short / DC Bus Fault /
Over Temperature / Over Load / Bat Over Charge
/ Battery Low / Bat Test Fail / Wiring Fault / Load
Over Setting Level / Fan Error)
T3 short to T9/T10
JP2NC
PIN 2 open to PIN 5
T3 open to T9/T10
N/A
PIN 6 short to PIN 5
Activated when UPS is OFF or in Bypass Mode
T4 short to T9/T10
JP3NO
PIN 7 short to PIN 5
Activated when Battery Low
T5 short to T9/T10
JP3NC
PIN 7 open to PIN 5
T5 open to T9/T10
N/A
PIN 8 short to PIN 5
UPS is on
T7 short to T9/T10
JP4NO
PIN 9 short to PIN 5
Activated when Utility Power Fails
T6 short to T9/T10
JP4NC
PIN 9 open to PIN 5
T5 open to T9/T10
Example Application
Provide 12VDC from COMMON(PIN 5/T9/T10) to GND(PIN 3/T2).
1. Remote Monitor Install alerting mechanism from DB-9 port/
Terminal(PIN 1/T8, PIN 2/T3, PIN 6/T4, PIN 7/T5, PIN 8/T7, PIN 9/T6)
to GND(PIN 3/T2).
2. Remote Shutdown Install a push button from COMMON
(PIN 5/T9/T10) to REMOTE SHUTDOWN(PIN 4/T1). Press the
button for at least 5 seconds to shut off the UPS remotely.
Note: When the UPS is in battery mode, the shutdown pins
(PIN 4 & PIN 3) require a minimum of 5 seconds of high level signal
(connection to +12VDC) to perform the UPS shutdown where output is
turned off after 120 seconds.
1
6
2
7
3
4
5
8
9
UPS FAIL
SUMMARY ALARM
GND (Common for PIN 4)
REMOTE SHUTDOWN
COMMON (For Relays)
BYPASS / UPS OFF
BATTERY LOW
UPS ON
POWER FAIL
12V
Conformance Approvals
FCC Warning
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does not cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
CyberPower Technical Support
Phone: 1-877-297-6937
Email: tech@cpsww.com
Web: www.CPSww.com
Mail: 4241 12th Avenue E, Suite 400 Shakopee, MN 55379
Hours of Operation:
Monday – Friday, 7:00am – 6:00pm (CST)
Entire contents copyright © 2015 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is
prohibited.
