About this manual
This bracket is designed for ceiling mounting installation.
Before installing and using this unit, please read this manual carefully.
Be sure to keep it handy for later reference.
CAUTION:
Install this bracket securely according to this
installation manual. Be aware that allowing the
bracket to fall with the camera on it may cause
personal injury.
bSpecifications
Color: Beige
Material: Metal
Waterproof Standard: Conforming to IP66
Weight: Approx. 700 g (1.5 lb)
Allowable Load: Max. 20 kg (44.1 lb)
Dimensions:
Example of
indoor use
Example of
outdoor use
☞P1 ☞P2
Important
• Be careful when opening holes for installing the
unit. Work with the power and video cables pulled
out for easy installation.
• Make sure to properly perform waterproofing for the
ceiling where you are installing the unit.
• Make sure that the surface in the installation
location has no unevenness and is strong enough
to bear the total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -30°C and +50°C
(-22°F and +122°F) (no condensation allowed).
Ǿ96 (3.8)
Ǿ130 (5.1)
Ǿ8.5 (0.3)
PDǾ102 (4.0)
45˚
329 (13.0)
300 (11.8)
63 (2.5)
63 (2.5)
Ǿ48
(1.9)
Unit: mm (inch)
INSTRUCTION MANUAL
Pendant Mounting Bracket
VA-80BP
Features and specifications are subject to change without
prior notice or obligations.
English
Bolts (20 mm/0.8”)
Waterproof gasket
Waterproof tape
Waterproof ring
Accessories (For outdoor housing)
This installation should be made by a qualified service
person and should conform to all local codes.
L9BHN_WA(VA-80BP)(GB_JP).book 0 ページ ２００６年１２月２７日 水曜日 午後１時５分
1
Indoor Type
Make sure to also consult the relevant instruction manuals.
1
Mark the locations on the ceiling and drill the holes
for the cables and screws.
And pull out the cables from the ceiling hole and
pass them through the bracket as shown in the
figure.
2
With sticker (A) facing toward you, fix the bracket
to the ceiling using commercially available screws
(B) in 4 places.
3
Mount the power board unit onto the attachment.
(1) Pass the screws supplied with the attachment
through each of the power board unit screw holes
(C) and fasten them loosely using washers
(4 places).
(2) Align the blue sticker (D) on the attachment and the
arrow (D) of the same color on the power board
unit, and tighten firmly the screws loosely
fastened in the previous step.
4
Fasten them loosely at two diagonal points using
the supplied bolts (E).
5
Thread the bolts (E) loosely fastened in step 4
through the bracket’s bolt holes (F) with sticker (A’)
aligned with sticker (A) and turn the bracket
clockwise.
6
Put the remaining bolts (E) to the other bracket bolt
holes and tighten the 4 bolts (F) securely.
• To fix the attachment, use the hexagonal wrench
supplied with the attachment.
• Make sure that the attachment is fixed, peel-off the
stickers.
7
Connect the cables to the power board unit and
mount the camera unit onto it.
☞ For details, please refer to Installation Manual that
comes with the camera unit.
“Connections and Settings”
“Surface Mount”
• Be sure to fix the bracket securely using M8 (5/16”)
screws. Using other bolt sizes may cause the bracket to
fall together with the camera on it.
• Route the connected cables so that they do not touch the
power board unit and other parts.
a
b
C
C
C
C
Power Board Unit:
VA-84S/80S
Attachment: VA-80A
D; Blue
E
4
5
6
F
F
A
A’
E
E
2
1
B
B
A
A’
M8 (5/16”): 40 mm (1.6”) or more
a
b
E
Attachment accessories
Screws, washers
(for power borad
unit)
Hexagonal
wrench
Bolts (10 mm/0.4”)
L9BHN_WA(VA-80BP)(GB_JP).book 1 ページ ２００６年１２月２７日 水曜日 午後１時５分
2
Outdoor Type
Make sure to also consult the relevant instruction manuals.
1
Mark the locations on the ceiling and drill the holes
for the cables and screws.
And pull out the cables from the ceiling hole and
pass them through the bracket as shown in the
figure.
2
With sticker (A) facing toward you, fix the bracket
to the ceiling using commercially available screws
(B) in 4 places.
3
Mount the dome cover and the power board unit
onto the housing.
☞ For details, please refer to the Outdoor Housing
Instruction Manual.
4
Place the supplied waterproof gasket (C) on top of
the outdoor housing with the power board unit
mounted, and fasten them loosely at two diagonal
points using the supplied bolts (D).
5
Thread the bolts (D) loosely fastened in step 4
through the bracket’s bolt holes (E) with sticker (A’)
aligned with sticker (A) and turn the bracket
clockwise.
6
Put the remaining bolts (D) to the other bracket bolt
holes and tighten the 4 bolts (D) securely.
• To fix the housing, use the hexagonal wrench
supplied with the housing.
• Make sure that the housing is fixed, peel-off the
stickers.
7
Connect the cables to the power board unit and
mount the camera unit onto it.
☞ For details, please refer to the Outdoor Housing
Instruction Manual.
“3. Connecting cables”
“4. Mounting the camera unit”
• Be sure to fix the bracket securely using M8 (5/16”)
screws. Using other bolt sizes may cause the bracket to
fall together with the camera on it.
• Route the connected cables so that they do not touch the
power board unit and other parts.
Outdoor Housing: VA-80EX
Dome Cover:
• VA-CM8C (Clear)
• VA-CM8S (Smoked)
Video cable
Power Board Unit: VA-84S/80S
1. Attaching the dome cover
2. Mounting the power board unit
D
4
5
6
C
E
A
D
E
2
1
BB
A’
A
A’
D
Waterproof ring (supplied):
Attach the ring as necessary.
M8 (5/16”): 40 mm (1.6”) or more
L9BHN_WA(VA-80BP)(GB_JP).book 2 ページ ２００６年１２月２７日 水曜日 午後１時５分
/
