Sanyo VA-80BW User manual

Brand: Sanyo

Model: VA-80BW

Category: Security camera accessories

Type: User manual

About this manual

This bracket is designed for ceiling mounting installation.

Before installing and using this unit, please read this manual carefully.

Be sure to keep it handy for later reference.

CAUTION:

Install this bracket securely according to this

installation manual. Be aware that allowing the

bracket to fall with the camera on it may cause

personal injury.

bSpecifications

Color: Beige

Material: Metal

Waterproof Standard: Conforming to IP66

Weight: Approx. 750 g (1.7 lb)

Allowable Load: Max. 20 kg (44.1 lb)

Dimensions:

Example of

indoor use

Example of

outdoor use

☞P1 ☞P2

Important

• Be careful when opening holes for installing the

unit. Work with the power and video cables pulled

out for easy installation.

• Make sure to properly perform waterproofing for the

wall where you are installing the unit.

• Make sure that the surface in the installation

location has no unevenness and is strong enough

to bear the total weight of the unit.

• Install this unit in an environment where the

temperature range stays between -30°C and +50°C

(-22°F and +122°F) (no condensation allowed).

Ǿ97 (3.8)

75 (3.0)

105 (4.1)

240 (9.4)

192 (7.6)

161 (6.3)

56 (2.2)

17(0.7)

191 (7.5)

4-Ǿ10.8 (0.4)

Unit: mm (inch)

INSTRUCTION MANUAL

Wall Mounting Bracket

VA-80BW

Features and specifications are subject to change without

prior notice or obligations.

English

Bolts, washers Rubber band

Accessories (For outdoor housing)

This installation should be made by a qualified service

person and should conform to all local codes.

L9BHM_WA(VA-80BW)(GB_JP).book 0 ページ２００６年１２月２７日　水曜日　午前１１時１９分

Indoor Type

Make sure to also consult the relevant instruction manuals.

Mark the locations on the wall and drill the

holes for the cables and screws.

And pull out the cables from the wall hole and

pass them through the bracket as shown in

the figure.

Fix the bracket to the wall using commercially

available screws (A) in 4 places.

Mount the power board unit onto the

attachment.

(1)Pass the screws supplied with the

attachment through each of the power board

unit screw holes (B) and fasten them loosely

using washers (4 places).

(2) Align the blue sticker (C) on the attachment

and the arrow (C) of the same color on the

power board unit, and tighten firmly the

screws loosely fastened in the previous

step.

With sticker (D) facing toward you, fix the

attachment onto the bracket using the 4 bolts

(E) supplied with the attachment.

• To fix the attachment, use the hexagonal

wrench supplied with the attachment.

• Make sure that the attachment is fixed, then

peel-off the sticker.

Connect the cables to the power board unit

and mount the camera unit onto it.

☞ For details, please refer to Installation Manual that

comes with the camera unit.

“Connections and Settings”

“Surface Mount”

• Be sure to fix the bracket securely using M8 (5/16”)

screws. Using other bolt sizes may cause the

bracket to fall together with the camera on it.

• Route the connected cables so that they do not

touch the power board unit and other parts.

Attachment accessories

Screws, washers

(for power borad

unit)

Hexagonal

wrench

Bolts (10 mm/0.4”)

M8 (5/16”): 40 mm (1.6”) or more

Video cable

Connection cables

Power Board Unit:

VA-84S/80S

Attachment: VA-80A

C; Blue

L9BHM_WA(VA-80BW)(GB_JP).book 1 ページ２００６年１２月２７日　水曜日　午前１１時１９分

Make sure to also consult the relevant instruction manuals.

Mark the locations on the wall and drill the

holes for the cables and screws.

And pull out the cables from the wall hole and

pass them through the bracket as shown in

the figure.

Fix the bracket to the wall using commercially

available screws (A) in 4 places.

Mount the dome cover and the power board

unit onto the housing.

☞ For details, please refer to the Outdoor Housing

Instruction Manual.

“1. Attaching the dome cover”

“2. Mounting the power board unit”

Attach the supplied rubber bands (B) to the

housing as shown in the figure.

With sticker (C) facing toward you,

temporarily mount the housing on the

bracket.

Fix the housing onto the bracket using 4 sets

of supplied bolts and bolt washers (D).

• To fix the housing, use the hexagonal wrench

supplied with the housing.

• Make sure that the housing is fixed, peel off the

sticker, then remove the rubber band.

Connect the cables to the power board unit

and mount the camera unit onto it.

☞ For details, please refer to the Outdoor Housing

Instruction Manual.

“3. Connecting cables”

“4. Mounting the camera unit”

• Be sure to fix the bracket securely using M8 (5/16”)

screws. Using other bolt sizes may cause the

bracket to fall together with the camera on it.

• Route the connected cables so that they do not

touch the power board unit and other parts.

Outdoor Type

This mounting bracket can be installed on a pole or a wall

corner by using the appropriate mounting adaptor. For

installation details, refer to the instruction manual for the pole

mounting adaptor (VA-80AP) or the corner mounting adaptor

(VA-80AC).

M8 (5/16”): 40 mm (1.6”) or more

Video cable

Connection cables

Outdoor Housing: VA-80EX

Dome Cover:

• VA-CM8C (Clear)

• VA-CM8S (Smoked)

Video cable

Power Board Unit:

VA-84S/80S

1. Attaching the dome cover

2. Mounting the power board unit

L9BHM_WA(VA-80BW)(GB_JP).book 2 ページ２００６年１２月２７日　水曜日　午前１１時１９分

Sanyo VA-80BW User manual

Brand: Sanyo

Model: VA-80BW

Category: Security camera accessories

Type: User manual

Download PDF

report

Sanyo VA-80BW User manual

Sanyo VA-80BW User manual

Related papers

Other documents