2. RAB Lighting
  3. BLH400P22DLPSQ

RAB Lighting BLH400P22DLPSQ, BHH250P16PSQ, BHH400P22PSQ, BLH250AW16DLPSQ, BLH250P16DLPSQ, BLH400AW16DLPSQ Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the RAB Lighting BLH400P22DLPSQ Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2012 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Applies to CAT#...
BLH250AW16DLPSQ BLH400AW16DLPSQ BLH250AW22DLPSQ BLH400AW22DLPSQ
BLH250P16DLPSQ BLH400P22DLPSQ
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or
email: marketing@rabweb.com
1
• AQuadtapballast120/208/240/277Vis
suppliedandfactorywiredfor277V.To
changeinputvoltageremovetheAccess
PlatefromtheJunction Box.Rewireto
changethetaptothedesiredvoltage
andcapanyunusedballasttaps.
• Slidecordthroughthehookandthread
intotheJunction Box.Tighten.
• ForHighBayxtures,mounttheHigh
BayBracket(BBH)beforehanging
xtures.Seeinstructionsbelow.
• MountBallast Housingwithhookto
sturdyceilingstructure(UseSafety
Ballast Housing Mounting and Wiring
Hookandchaintotemporarilysupportwhileinstallingthexture).
• Connectcordtosupplywiresusingapprovedwireconnectors.
• Tightenscrewonhooktosecurexture.
• IfnecessaryadjusttheSlide Platetobalancethexturebylooseningtwoscrews.
High Bay Bracket Mounting
• BeforemountingBallastHousingto
ceiling,mounttheBrackettothe
BallastHousingwith4screwsprovided.
• Theremainingscrewsandwirenutsare
usedtomounttheBrackettothe
AluminumReectorortothecollarfor
thePrismaticRefractor.Seethe
appropriatesectionforfurtherdetail.
• Clamp Bands,CB16orCB22,are
requiredformountingtheDrop
Lenstothereectororrefractor.
• Lampsshouldbeinstalledpriorto
thisstep.
• Loosenscrewfromonesideofthe
clipontheClamp Band.
• StretchoverDrop Lensand
ReectororRefractorasshown
withthewidersidedownholding
thedroplens.
• Tightenscrewsecuringassembly.
Prismatic or
Aluminum
Reector
Clamp Band
Access Plate
Junction Box
Ballast Housing
Slide Plate
Safety Hook
Applies to CAT#...
BHH250A16PSQ BHH400A16PSQ BHH250A22PSQ BHH400A22PSQ
BHH250P16PSQ BHH400P22PSQ
Bracket
Drop Lens for Low Bay
Drop Lens
Note:Theseinstructionsdonotcoveralldetailsorvariationsinequipmentnordotheyprovidefor
everypossiblesituationduringinstallation,operationormaintenance.
HI/LOW-IN0813
HI-BAY/LOW BAY INSTRUCTIONS
2
3
• TheReectormountstothebottom
tabsofthesuppliedbracket(BBH)with(4)
screwsandReector Wing Nutsprovided
Bracket.
• LoosentheSide Wing Nutsandsetthe
bracketatthedesiredsetting.Tightenwing
nuts.
• TheReectormountsdirectlytothe
Ballast Housingwith(4)8-32x3/8”
screwsprovidedwiththeBallast
Housing.
• AftermountingtheReectorand
installingthelampseetheDropLens
instructionsonpage4.
• CR16isrequiredforBHH250P16and
CR22isrequiredforBHH400P22 for
themountingofthePrismatic
Refractors.
• InserttheCollarthroughthe
Prismatic Refractorfromthebottom
asshown.TheCollarshouldbe
mountedtothebottomtheBracket
withthe4screwsandwingnutspro-
videdwiththeBracket(BBH).
• AftermountingtheRefractorbend
overthe(4)tabs,securingthe
RefractortotheCollar.To get
maximum distance between lamp and
Refractor, loosen the Side wing nuts on
the bracket and adjust it to A1 position
on bracket, close to the Ballast Housing.
• InserttheCollarthroughthe
Prismatic Refractorfromthebottom.
• MountCollardirectlytoBallast
Housingusing(4)8-32screws
providedwiththeBallastHousing.
• AftermountingtheRefractor,bend
overthe(4)tabsontheCollarto
secureRefractortotheCollar.
Applies to CAT#...
BHH250A16PSQ BHH400A16PSQ
BHH250A22PSQ BHH400A22PSQ
Applies to CAT#...
BHH250P16PSQ BHH400P22PSQ
Applies to CAT#...
BLH250AW16DLPSQ BLH400AW16DLPSQ
BLH250AW22DLPSQ BLH400AW22DLPSQ
Applies to CAT#...
BLH250P16DLPSQ BLH400P22DLPSQ
Reector
Reector Wing Nuts
(2 not shown)
Side Wing Nuts
Prismatic Refractor
Collar
Refractor Wing Nuts
(2 not shown)
Prismatic Refractor
Collar
Ballast
Housing
Ballast Housing
Reector Mounting Screws (4)
Natural Aluminum Reector for High Bay
White Aluminum Reector for Low Bay
Prismatic Refractor & Collar for High Bay
Prismatic Refractor & Collar for Low Bay
Side Wing Nuts
/