RAB Lighting BLH250P16DLPSQ Operating instructions

Brand: RAB Lighting

Model: BLH250P16DLPSQ

Type: Operating instructions

This manual is also suitable for

Easy Installation & Product Help

Tech Help Line

Call our experts 888 RAB-1000

rthvale, New Jersey 07647 USA

rabweb.com

Visit our website for product info

Answered promptly sales@rabweb.com

Applies to CAT#...

BLH250AW16DLPSQ BLH400AW16DLPSQ BLH250AW22DLPSQ BLH400AW22DLPSQ

BLH250P16DLPSQ BLH400P22DLPSQ

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the

job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or

email: marketing@rabweb.com

• AQuadtapballast120/208/240/277Vis

suppliedandfactorywiredfor277V.To

changeinputvoltageremovetheAccess

PlatefromtheJunction Box.Rewireto

changethetaptothedesiredvoltage

andcapanyunusedballasttaps.

• Slidecordthroughthehookandthread

intotheJunction Box.Tighten.

• ForHighBayxtures,mounttheHigh

BayBracket(BBH)beforehanging

xtures.Seeinstructionsbelow.

• MountBallast Housingwithhookto

sturdyceilingstructure(UseSafety

Ballast Housing Mounting and Wiring

Hookandchaintotemporarilysupportwhileinstallingthexture).

• Connectcordtosupplywiresusingapprovedwireconnectors.

• Tightenscrewonhooktosecurexture.

• IfnecessaryadjusttheSlide Platetobalancethexturebylooseningtwoscrews.

High Bay Bracket Mounting

• BeforemountingBallastHousingto

ceiling,mounttheBrackettothe

BallastHousingwith4screwsprovided.

• Theremainingscrewsandwirenutsare

usedtomounttheBrackettothe

AluminumReectorortothecollarfor

thePrismaticRefractor.Seethe

appropriatesectionforfurtherdetail.

• Clamp Bands,CB16orCB22,are

requiredformountingtheDrop

Lenstothereectororrefractor.

• Lampsshouldbeinstalledpriorto

thisstep.

• Loosenscrewfromonesideofthe

clipontheClamp Band.

• StretchoverDrop Lensand

ReectororRefractorasshown

withthewidersidedownholding

thedroplens.

• Tightenscrewsecuringassembly.

Prismatic or

Aluminum

Reector

Clamp Band

Access Plate

Junction Box

Ballast Housing

Slide Plate

Safety Hook

Applies to CAT#...

BHH250A16PSQ BHH400A16PSQ BHH250A22PSQ BHH400A22PSQ

BHH250P16PSQ BHH400P22PSQ

Bracket

Drop Lens for Low Bay

Drop Lens

Note:Theseinstructionsdonotcoveralldetailsorvariationsinequipmentnordotheyprovidefor

everypossiblesituationduringinstallation,operationormaintenance.

HI/LOW-IN0813

HI-BAY/LOW BAY INSTRUCTIONS

• TheReectormountstothebottom

tabsofthesuppliedbracket(BBH)with(4)

screwsandReector Wing Nutsprovided

Bracket.

• LoosentheSide Wing Nutsandsetthe

bracketatthedesiredsetting.Tightenwing

nuts.

• TheReectormountsdirectlytothe

Ballast Housingwith(4)8-32x3/8”

screwsprovidedwiththeBallast

Housing.

• AftermountingtheReectorand

installingthelampseetheDropLens

instructionsonpage4.

• CR16isrequiredforBHH250P16and

CR22isrequiredforBHH400P22 for

themountingofthePrismatic

Refractors.

• InserttheCollarthroughthe

Prismatic Refractorfromthebottom

asshown.TheCollarshouldbe

mountedtothebottomtheBracket

withthe4screwsandwingnutspro-

videdwiththeBracket(BBH).

• AftermountingtheRefractorbend

overthe(4)tabs,securingthe

RefractortotheCollar.To get

maximum distance between lamp and

Refractor, loosen the Side wing nuts on

the bracket and adjust it to A1 position

on bracket, close to the Ballast Housing.

• InserttheCollarthroughthe

Prismatic Refractorfromthebottom.

• MountCollardirectlytoBallast

Housingusing(4)8-32screws

providedwiththeBallastHousing.

• AftermountingtheRefractor,bend

overthe(4)tabsontheCollarto

secureRefractortotheCollar.

Applies to CAT#...

BHH250A16PSQ BHH400A16PSQ

BHH250A22PSQ BHH400A22PSQ

Applies to CAT#...

BHH250P16PSQ BHH400P22PSQ

Applies to CAT#...

BLH250AW16DLPSQ BLH400AW16DLPSQ

BLH250AW22DLPSQ BLH400AW22DLPSQ

Applies to CAT#...

BLH250P16DLPSQ BLH400P22DLPSQ

Reector

Reector Wing Nuts

(2 not shown)

Side Wing Nuts

Prismatic Refractor

Collar

Refractor Wing Nuts

(2 not shown)

Prismatic Refractor

Collar

Ballast

Housing

Ballast Housing

Reector Mounting Screws (4)

Natural Aluminum Reector for High Bay

White Aluminum Reector for Low Bay

Prismatic Refractor & Collar for High Bay

Prismatic Refractor & Collar for Low Bay

Side Wing Nuts

RAB Lighting BLH250P16DLPSQ Operating instructions

Brand: RAB Lighting

Model: BLH250P16DLPSQ

Type: Operating instructions

This manual is also suitable for

Download PDF

report

RAB Lighting BLH250P16DLPSQ Operating instructions

This manual is also suitable for

RAB Lighting BLH250P16DLPSQ Operating instructions

Related papers

Other documents