RAB Lighting BHH250P16PSQ Operating instructions

Type
Operating instructions
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2012 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Applies to CAT#...
BLH250AW16DLPSQ BLH400AW16DLPSQ BLH250AW22DLPSQ BLH400AW22DLPSQ
BLH250P16DLPSQ BLH400P22DLPSQ
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the
job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or
email: marketing@rabweb.com
1
• AQuadtapballast120/208/240/277Vis
suppliedandfactorywiredfor277V.To
changeinputvoltageremovetheAccess
PlatefromtheJunction Box.Rewireto
changethetaptothedesiredvoltage
andcapanyunusedballasttaps.
• Slidecordthroughthehookandthread
intotheJunction Box.Tighten.
• ForHighBayxtures,mounttheHigh
BayBracket(BBH)beforehanging
xtures.Seeinstructionsbelow.
• MountBallast Housingwithhookto
sturdyceilingstructure(UseSafety
Ballast Housing Mounting and Wiring
Hookandchaintotemporarilysupportwhileinstallingthexture).
• Connectcordtosupplywiresusingapprovedwireconnectors.
• Tightenscrewonhooktosecurexture.
• IfnecessaryadjusttheSlide Platetobalancethexturebylooseningtwoscrews.
High Bay Bracket Mounting
• BeforemountingBallastHousingto
ceiling,mounttheBrackettothe
BallastHousingwith4screwsprovided.
• Theremainingscrewsandwirenutsare
usedtomounttheBrackettothe
AluminumReectorortothecollarfor
thePrismaticRefractor.Seethe
appropriatesectionforfurtherdetail.
• Clamp Bands,CB16orCB22,are
requiredformountingtheDrop
Lenstothereectororrefractor.
• Lampsshouldbeinstalledpriorto
thisstep.
• Loosenscrewfromonesideofthe
clipontheClamp Band.
• StretchoverDrop Lensand
ReectororRefractorasshown
withthewidersidedownholding
thedroplens.
• Tightenscrewsecuringassembly.
Prismatic or
Aluminum
Reector
Clamp Band
Access Plate
Junction Box
Ballast Housing
Slide Plate
Safety Hook
Applies to CAT#...
BHH250A16PSQ BHH400A16PSQ BHH250A22PSQ BHH400A22PSQ
BHH250P16PSQ BHH400P22PSQ
Bracket
Drop Lens for Low Bay
Drop Lens
Note:Theseinstructionsdonotcoveralldetailsorvariationsinequipmentnordotheyprovidefor
everypossiblesituationduringinstallation,operationormaintenance.
HI/LOW-IN0813
HI-BAY/LOW BAY INSTRUCTIONS
2
3
• TheReectormountstothebottom
tabsofthesuppliedbracket(BBH)with(4)
screwsandReector Wing Nutsprovided
Bracket.
• LoosentheSide Wing Nutsandsetthe
bracketatthedesiredsetting.Tightenwing
nuts.
• TheReectormountsdirectlytothe
Ballast Housingwith(4)8-32x3/8”
screwsprovidedwiththeBallast
Housing.
• AftermountingtheReectorand
installingthelampseetheDropLens
instructionsonpage4.
• CR16isrequiredforBHH250P16and
CR22isrequiredforBHH400P22 for
themountingofthePrismatic
Refractors.
• InserttheCollarthroughthe
Prismatic Refractorfromthebottom
asshown.TheCollarshouldbe
mountedtothebottomtheBracket
withthe4screwsandwingnutspro-
videdwiththeBracket(BBH).
• AftermountingtheRefractorbend
overthe(4)tabs,securingthe
RefractortotheCollar.To get
maximum distance between lamp and
Refractor, loosen the Side wing nuts on
the bracket and adjust it to A1 position
on bracket, close to the Ballast Housing.
• InserttheCollarthroughthe
Prismatic Refractorfromthebottom.
• MountCollardirectlytoBallast
Housingusing(4)8-32screws
providedwiththeBallastHousing.
• AftermountingtheRefractor,bend
overthe(4)tabsontheCollarto
secureRefractortotheCollar.
Applies to CAT#...
BHH250A16PSQ BHH400A16PSQ
BHH250A22PSQ BHH400A22PSQ
Applies to CAT#...
BHH250P16PSQ BHH400P22PSQ
Applies to CAT#...
BLH250AW16DLPSQ BLH400AW16DLPSQ
BLH250AW22DLPSQ BLH400AW22DLPSQ
Applies to CAT#...
BLH250P16DLPSQ BLH400P22DLPSQ
Reector
Reector Wing Nuts
(2 not shown)
Side Wing Nuts
Prismatic Refractor
Collar
Refractor Wing Nuts
(2 not shown)
Prismatic Refractor
Collar
Ballast
Housing
Ballast Housing
Reector Mounting Screws (4)
Natural Aluminum Reector for High Bay
White Aluminum Reector for Low Bay
Prismatic Refractor & Collar for High Bay
Prismatic Refractor & Collar for Low Bay
Side Wing Nuts
  • Page 1 1
  • Page 2 2

RAB Lighting BHH250P16PSQ Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI