Extron TLP Pro 720M User manual

Extron
Brand
Extron
Model
TLP Pro 720M
Type
User manual

This manual is also suitable for

1
Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
TLP Pro 720M and TLP Pro 1020M • Setup Guide
Overview
The Extron TLP Pro 720M is a 7-inch wall mount touchpanel with a high resolution 800x480 LCD screen. The TLP Pro 1020M is
a 10-inch wall mount touchpanel with a high resolution 1024x600 LCD screen. They are ideal for any AV applications requiring
medium or large touchpanels with exible mounting options and fully customizable interfaces. This guide provides instructions for
experienced installers to mount and install a TLPPro 720M or TLP Pro 1020M touchpanel. For more complete instructions, see the
TLPPro720Series and TLPPro 1020 Series User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink
®
Pro touchpanels and third party touch interfaces.
Global Configurator
®
Plus and Professional — for setting up and conguring the control processor and touchpanel.
Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings, system
utilities, and user management for TouchLink Pro devices.
All three software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you will also require
IP address Subnet mask Gateway
User name — by default these are either admin or user.
Passwords — by default these are either extron (for admin) or the eld is left blank (for user).
Make a note of the touchpanel MAC address (see the label on the back panel).
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of
the TLP Pro 720 Series and TLP Pro 1020 Series User Guide or the IPL Pro User Guide.
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources
d’alimentation» du TLP Pro 720 Series and TLP Pro 1020 Series UserGuide ou du IPLProUserGuide.
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see “Mounting” below).
Connect cables to the touchpanels.
Connect the power cords and power on all devices.
Set up the Touchpanels for Network Communication
Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 4) or the Toolbelt feature of Global Congurator Professional or Global Congurator Plus to set
the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the touchpanel.
Configure the Touchpanels
The Global Configurator Professional Help File, the Global Configurator Plus Help File, and the GUI Designer Help File provide step-by-
step instructions and more detailed information. The Global Congurator Professional and Global Congurator Plus help les include
an introduction to the software and sections on how to start a project and conguration.
Mounting
The following optional mounting kits are available for the touchpanels. The kits must be purchased separately. Follow the instructions
provided with the kit.
z Rack mounting — RM 710M for the TLP Pro 720M or RM 1000M for the TLP Pro 1020M.
z Back Box wall mounting — BB 710 or EWB 710 for the TLP Pro 720M or BB 1000 or the EWB 1000 for the TLP Pro 1020M.
www.extron.com
2
TLP PRO 720M and TLP PRO 1020M • Setup Guide (Continued)
Wall-Mounting or Furniture-Mounting
The TLP Pro 720M or TLP Pro 1020M can be mounted directly to the wall or directly into furniture without a kit.
ATTENTION:
• Do not install the TLP Pro 720M or TLP Pro 1020M in a re resistant rated wall or partition assembly.
• Ne pas installer le TLP Pro 720M or TLP Pro 1020M dans un mur résistant au feu ou une cloison.
To mount either touchpanel into drywall, follow these steps. The steps are similar for mounting the unit in furniture (such as a podium
or table). Figure 1 shows the TLP Pro 720M, but the instructions for the TLP Pro 1020M are the same.
1. Use the template for either the TLP Pro 720M or TLP Pro 1020M (available at www.extron.com) as a guide to mark the wall at a
suitable location. Ensure that you download the correct template for your touchpanel. Ensure that your printer does not scale the
template when it is printed. The template must be printed at 100%.
2. Use a wallboard saw or jigsaw to cut away the material within the guidelines drawn in step 1.
ATTENTION:
• Cut inside the guidelines to maximize the contact between the wallplate adapter and the drywall.
• Couper en suivant le marquage an d’optimiser le contact entre la plaque murale d’adaptation et la cloison.
3. If there is insulation inside the drywall, remove at least 6 inches of insulation in all directions around the opening. If the opening is
less than 6 inches from a wall stud, remove all the insulation between the opening and the wall stud.
4. If necessary, separate the bezel from the touchpanel, using the provided removal tool (see gure 1,
1
). Insert the tool into the
notches on the bottom surface of the bezel and gently separate the bezel from the touch panel.
5. Ensure all the locking arms are ush with the unit and check the size of the opening by inserting the touchpanel into it. If
necessary, use a saw, le, or sandpaper to enlarge the hole.
CAUTION: Smooth the edges of the opening to avoid personal injury during installation and to avoid damage to the
touchpanel or cables.
ATTENTION: Limez les bords de l’ouverture an d’éviter toute blessure lors de l’installation et éviter d’endommager la
plaque murale d’adaptation ou les câbles.
6. Remove the touchpanel from the hole and run the cables inside the wall to the hole, leaving enough slack in the cables to connect
them to the back of the touchpanel.
7. Plug the cables into the rear panel connectors (see page 4).
z Connect the LAN port to the PoE power injector or a PoE enabled switch.
z If you use the LAN port only as a network connection, connect a 12 VDC,
1.0 A power supply to the 2-pole captive screw power input connector.
8. Push excess cables into the wall cavity.
9. Use a Phillips head screwdriver to tighten the
locking arm screws (
2
). As the screws tighten,
the locking arms rotate behind the wall and hold
the adapter in place.
ATTENTION:
• Do not overtighten the screws as this
can damage the catches or the wall.
• Ne serrez pas trop les vis au risque
d’endommager les attaches ou le mur.
z The TLP Pro 720M has four locking arms,
two at the top and two at the bottom.
z The TLP Pro 1020M has ve locking arms,
three at the top and two at the bottom.
10. If required, perform the initial conguration, using
the Setup Menu (see page 4).
Bezel snaps to unit
(2 tabs on each side).
Tighten screws to
rotate locking arms.
2
3
Insert r
emoval tool
into slots to
r
emove bezel.
1
Figure 1. Mounting the TLP Pro 720M
11. Press the bezel onto the touchpanel by pushing
the catches on the bezel into the corresponding
holes on the front of the panel (
3
).
3
Product Category
Front Panel Features
The TLP Pro 720M and TLP Pro 1020M ship with the bezels attached.
The units (not to scale) are shown in the diagram to the right.
Figure 2 shows the front panel features with the bezel removed. (To
remove the bezel see step 4 on the previous page.)
Extron
TLP Pro 720M TLP Pro 1020M
C
C
F
FH
IJ
J
D
A
G
G
B
B
AA
A
D
E E
E I
H
Figure 2. TLP Pro 720M (left) and TLP Pro 1020M (right) Front Panels (not to scale)
A
Status lights — one on each top corner provide system feedback. They light red or green and they blink or light continuously
B
Ambient light sensor — monitors ambient light level and adjusts screen brightness, based on the settings congured using the
Setup Menu (see page 4).
C
Bezel attachment points — The TLP Pro 720M has eight attachment points (two on each side, two on the top edge, and two on
the bottom edge); the TLP Pro 1020M has ten attachment points (three on each side, two on the top edge, and two on the bottom
edge). Use the Extron removal tool to separate the front bezel from the touchpanel. Insert the tool into one of the slots found on
the bottom surface of the unit and pry the bezel away from the touchpanel.
D
LCD screen — TLP Pro 720M: 7-inch screen with 800x480 resolution. TLP Pro 1020M: 10-inch screen with 1024x600 resolution.
E
Speakers — provide audible feedback for the user. The TLP Pro 720M has one on the left side of the panel, under the screen.
The TLP Pro 1020M has two, placed under the screen, one on each side.
F
Motion sensor — detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis. When no
motion has been detected for a user-dened period of time, the touchpanel enters into sleep mode. When motion is detected by
the sensor, the screen display is restored and active.
G
Communication LED — shows the conguration and connection status of the touchpanel. The LED is unlit during normal
operation (the touchpanel is congured and connected to an IP Link Pro control processor). It blinks red if the touchpanel has
been congured but is not connected to an IP Link Pro control processor. It is permanently lit if the touchpanel has not been
congured and is not connected to an IP Link Pro control processor. The indicator can be toggled between enabled and disabled,
using the Setup Menu (see page 4)
H
Menu button — activates the Setup Menu and calibration screen (see page4).
I
Reset button — pressing the reset button allows the unit to be reset in any of three different modes (see below).
J
Reset LED — provides feedback about the reset status when the user presses the reset button.
Reset Modes: a Brief Summary
The TLP Pro 720M and TLP Pro 1020M offer the following reset modes (see the TLP Pro 720 Series and TLP Pro 1020 Series User
Guide. for complete information):
• Use factory firmware:
Press and hold the Reset button (gure 2,
I
) while applying power to the unit. Use this
mode to replace rmware in the event of rmware failure.
• Reset All IP Settings:
Press and hold the Reset button for 6 seconds. After the Reset LED (gure 2,
J
) ashes
twice, release and momentarily press the Reset button. Use this mode to reset all network
settings without affecting user-loaded les.
• Reset to Factory
Defaults:
Press and hold the Reset button for 9 seconds. After the Reset LED ashes three times,
release and momentarily press the Reset button. Use this mode to return the interface to
factory default settings.
4
68-2405-51 Rev. C
05 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
TLP PRO 720M and TLP PRO 1020M • Setup Guide (Continued)
Rear Panel Features
Extron
A
A
B
B
Figure 3. TLP Pro 720M (left) and TLP Pro 1020M (right) Rear Panels
A
Power connector — Connect a 12 VDC, 1.0 A power supply (not included) to this 2-pole captive screw connector.
ATTENTION:
• The TLP Pro 720M and TLP Pro 1020M can use a 12 VDC desktop power supply and are also Power over Ethernet
(PoE 802.3af, class3) compliant. Do not connect either power supply before reading the Attention in the Power
Supply section of the TLP Pro 720 Series and TLP Pro 1020 Series User Guide.
• Le TLP Pro 720M et le TLP Pro 1020M peut utiliser une source d’alimentation externe 12 Vcc, et sont également
compatible avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources d’alimentation
externes avant d’avoir lu les mises en garde dans la section «PowerSupply» du TLP Pro 720 Series and TLPPro
1020 Series User Guide.
NOTES:
• The TLP Pro 720M and TLP Pro 1020M ship without a power supply. Either the 12 VDC, 1.0 A power supply or the
power injector must be purchased separately.
• If a 12 VDC and a PoE power injector are both connected to the TLP Pro 720M or TLP Pro 1020M, the power
injector takes precedence. If a PoE power loss is detected, the touchpanel switches seamlessly to the 12 VDC
supply without needing a system reboot.
B
Network and Power over Ethernet connector — for the TLP Pro 720M, this is in the top surface of the recessed area (see the
arrow). Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector. The connector can
also be used with a PoE power injector (not provided).
An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.
Setup Menu
Press the menu button (
H
in gure 2, on the previous page) to open the
setup menu. Select any of the ve available screens (Status, Network,
Display, Audio, and Advanced) by pressing the appropriate button in
the navigation bar at the top of the screen (for more information, see the
TLPPro 720 Series and TLP Pro 1020 Series User Guide).
Figure 4 shows the setup menu for the TLP Pro 720M. The setup menu for
the TLP Pro 1020M is almost identical.
Press the menu button for at least 3 seconds to open the calibration
screen. Follow the on-screen instructions.
Status
Display Audio Advanced Exit
Network
Info
Model: TLP Pro 720M
Part Number: 60-1394-02
Firmware
Version:
1.00
PoE Status:On
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLP-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
800x480
N/A
5 Minutes
Audio
Master Volume:
Master Mute: Off
99
Advanced
Controller IP: N/A
Project Size: N/A
Figure 4. Setup Menu: Status page for TLP Pro 720M
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron TLP Pro 720M User manual

Extron
Brand
Extron
Model
TLP Pro 720M
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents