Extron TLP Pro 1022M Adapter User manual

Type
User manual
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
t
ouchpa
nel to the power source.
TLP Pro 1022M Adapter Mount • Installation Guide
Overview
The adapter mount enables the TLP Pro 1022M touchpanel to be retrotted into accessories (BB 1000M, EWB 1000, and
RM 1000M) and openings in drywall and furniture that were created for the TLP 1000MV or TLP Pro 1020M touchpanels.
This guide describes:
Attaching the Adapter Mount to an Existing Hole in Drywall or a BB 1000M
Attaching the Adapter Mount to an Existing RM 1000M or EWB 1000
Mounting the Touchpanel
For complete information about preparing the installation site, see the user guide for the TLP 1000MV, TLP Pro 1020M, or
mounting accessory at www.extron.com.
Attaching the Adapter Mount to an Existing Hole in Drywall or a BB 1000M
2
Adapter Mount
Front View
Rear View
(showing Locking Arms)
3
4
Drywall
Locking Ar
m
1
#8-32 screws (4)
TOP
Figure 1. Attaching the Adapter Mount to an Existing Hole.
1. Loosely insert the four provided #8-32 mounting plate screws into the adapter mount (see gure 1,
1
).
2. Insert the adapter mount over the opening. Tighten the screws (
2
) that hold the locking arms (
3
).
The arms turn (
4
) and hold the adapter mount loosely in place.
3. Align the adapter mount so that it is level.
4. Tighten the locking arms so that the adapter mount is held securely. Do not overtighten.
www.extron.com
2
68-3133-01 Rev. A
05 17
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Attaching the Adapter Mount to an Existing RM 1000M or EWB 1000
The adapter mount slightly overhangs the EWB 1000.
EWB 1000
Rear View
A
dapter Mount
Inside View
(showing Locking Arms)
Apply
anti-slip
rubber
Locking Ar
m
TOP
Figure 2. Attaching the Adapter Mount to an Existing RM 1000M or EWB 1000
1. If you are using this kit to adapt an existing
RM 1000M or EWB 1000, place the four provided 2 inch
strips of anti-slip rubber on the inside clamping surface of the
mounting accessory (see gure 2).
2. Follow steps 1-3 on the previous page to secure the mounting
adapter.
Mounting the Touchpanel
1. Attach the touchpanel mounting plate to the adapter mount
(see gure 3,
1
). Ensure the mounting plate is in the
correct orientation with the hooks at the top and facing out
from the wall (
2
).
2. Tighten the four #8-32 mounting plate screws (
1
) so that
the mounting plate is held securely.
3. Run cables to the opening and connect them to the rear
panel of the TLP Pro 1022M.
4. If necessary, insert the provided pan head screws and
washers into the mounting screw slots on the bottom of the
touchpanel (see the bottom inset of gure 3,
3
).
5. Hold the touchpanel at a slight angle and lower the notches
at the top of the back panel over the hooks of the mounting
plate (
2
).
6. Swing the bottom of the touchpanel inwards.
7. Fasten the touchpanel to the mounting plate by tightening
the pan head screws (
4
).
Fasten the touchpanel
to the mounting plate
w/ pan head screws (2) in
base of touchpanel.
1
2
3
Rear View
3
Insert pan head screws
with washers (2) into the
mounting screw slot.
TLP PRO 1022M
TLP Pro 1022M
Mounting Pate
4
TOP
Figure 3. Mounting the Touchpanel
  • Page 1 1
  • Page 2 2

Extron TLP Pro 1022M Adapter User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI