Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

Page is loading ...

2

3

Inhalt

1. Allgemeine Beschreibung...................................................................................................................................4

2. Sicherheitshinweise........................................................................................................................................... 4

3. Montage des WDDG1-Gehäuses ........................................................................................................................ 5

4. Montage des WDDG2-Gehäuses ........................................................................................................................ 5

5. Anschluss.......................................................................................................................................................... 6

6. Beschreibung der Einstellmöglichkeiten bei unterschiedlichen Kamerapaketen................................................. 7

7. Fehlersuche und Fehlerbehebung ....................................................................................................................10

8. Spezikationen und Zubehör............................................................................................................................ 10

9. Maßzeichnungen ............................................................................................................................................. 44

Contents

1. Safety Instructions ........................................................................................................................................... 14

2. General Descriptions........................................................................................................................................ 14

3. Mounting the WDDG1 Housing .........................................................................................................................15

4. Mounting the WDDG2 Housing .........................................................................................................................15

5. Connection ......................................................................................................................................................16

6. Description of the Possible Settings for Various Camera Packages ................................................................... 17

7. Troubleshooting and Rectication of Faults ...................................................................................................... 20

8. Specications and Accessories ........................................................................................................................ 20

9. Dimensional Drawings ..................................................................................................................................... 44

Sommaire

1. Consignes de sécurité...................................................................................................................................... 24

2. Description générale........................................................................................................................................24

3. Montage du boîtier WDDG1.............................................................................................................................. 25

4. Montage du boîtier WDDG2.............................................................................................................................. 25

5. Connexion........................................................................................................................................................ 26

6. Description des possibilités de réglage pour les différents ensembles de caméras........................................... 27

7. Recherche de défauts et remèdes.................................................................................................................... 30

8. Spécications et accessoires ........................................................................................................................... 30

9. Croquis............................................................................................................................................................ 44

Page is loading ...

14

15

1. General Description

• For ceiling and wall mounting

• Weatherproof and vandal-resistant design

• Clear polycarbonate dome with black interior insert

• 1/4” or 1/3” CCD B/W or colour board camera with various functions

• Easy to mount for interior or exterior use

2. Safety Instructions

• The instructions below must be followed for your own safety.

• Please read the safety instructions and operating instructions before connecting the device and putting it into

operation.

• Keep the operating instructions safe for use at a later date.

• Never operate the camera outside of the specications as this may prevent the camera functioning.

• Never point the camera towards the sun with the lens open as this may prevent the sensor functioning.

• When laying the connection cable, it is essential to follow the instructions below: the cable must be laid in such

a way that it is not strained, bent or damaged and no moisture can penetrate.

• Installation and maintenance of the system may only be carried out by persons with appropriate authorisation

for this and in accordance with the installation instructions – taking into account all the applicable standards and

guidelines.

• The installer is responsible for maintaining IP 66/67.

• Only use rust-proof screws should be used to mount the housing and camera outside.

• Only original spare parts from the manufacturer may be used with the „eneo camera package”.

Maintenance:

• In order to get a clear picture, it is necessary to clean the dome regularly.

• Wipe it with a soft, damp cloth.

• Never clean the housing and dome with thinner, petrol or a scourer as this could cause permanent damage

to the surface.

14

15

3. Mounting the WDDG1 Housing

Wall and ceiling mounting

4. Mounting the WDDG2 Housing

W

G

A

Wall / ceiling

K

B

W

G

Wall / ceiling

K

Teon

strip

Note The operational side of the camera is mounted in the housing.

Prepare the mounting site for installation.

Loosen the 4 Torx screws on the housing, but do not completely remove them,

and remove the cap.

A Screw holes Mark the position of the back of the housing W on the surface on which the

device is to be mounted. The screw holes A in the attached plate and/or on the

back of the housing W may be used as a template.

W Back of housing Fix the back of the housing W on the desired surface (plug and cross-head

screws are enclosed) and feed through the cable. 1/3” or 1/2” opening.

Note When mounting on a ceiling, the camera must be installed within the housing.

G Housing cap Fasten housing cap G on the back of the housing.

Connection cable After connecting the power supply and attaching the coaxial cable to an

appropriate monitor, the camera is operational.

K Cable feed Rubber washer for cable feed

16

17

5. Connection Assignment

a) The cables should be assigned as follows for the ‚eneo camera package’ which is supplied with a connection cable

with open ends:

Model VK-1318/WDDG1/2, VKC-1413WDDG1/2,

VKC-144/WDDG1/2

VKC-148/WDDG1/2

Video output

white/yellow white

V earth

black screen

Power supply

red white/yellow

Note

Take note of the signal and voltage polarity !

Comments

The multi-wire connector cable with EDP No. 70226 is recommended for the

„eneo camera packages”, which are supplied with a connection cable with open ends.

b) The following connectors are mounted on the „eneo camera packages”, which are supplied with system cables

(video/DC):

Model VK-1320WDDG1/2, VKC-1414/WDDG1/2,

VKC-1324WDDG1/2, VKC-1326WDDG1/2

VKC-1327

Video output

BNC jack (white)

Power supply

A) Stereo jack connector (black) B) Adapter bushing (green), for 12VDC/24VAC

A)

B)

Note The operational side of the camera is mounted in the housing.

Prepare the mounting site for installation.

Loosen the 4 Torx screws on the housing, but do not completely remove them,

and remove the cap.

B Screw holes Mark the position of the back of the housing W on the surface on which the

device is to be mounted. The screw holes B in the back of the housing W may

be used as a template.

W Back of housing Fix the back of the housing W on the desired surface (plug and cross-head

screws are enclosed) and feed through the cable. 1/3” or 1/2” opening.

Note When mounting on a ceiling, the camera must be installed within the housing.

G Housing cap Fasten housing cap G on the back of the housing.

Connection cable After connecting the power supply and attaching the coaxial cable to an

appropriate monitor, the camera is operational.

K Cable feed 1/3” and 1/2” socket. The 1/2” high-strength cable gland is included in the

accessories. A dummy plug for the 1/3” socket is included.

16

17

6. Description of the Possible Settings for Various Camera Packages

SW1 and SW2LEVEL PHASE

SW1 / SW2

DSS / DN / IR / NOR

Level and phase

control (A, B)

For

camera package

LEVEL potentio-

meter control

IRIS VKC-1324/WDDG1/2

VKC-1326/WDDG1/2

VKC-1327/WDDG1/2

VKC-1414/WDDG1/2

Iris control. Correct using potentiometer control for very

over-exposed images or where the contrast is too low.

Adjust using test image (min. 3,000Lux) and oscilloscope

to 1Vp-p signal.

PHASE potentio-

meter control for

vertical phase

PHASE VKC-1326/WDDG1/2

VKC-1327/WDDG1/2

Potentiometer control to adjust the phase for mains

synchronisation.

Adjustment to the same phasing when using several

cameras avoids disruptive post-synchronisation of the

monitor when using video change-over switches

(only possible with models with AC supply voltage).

DSS, digital slow

shutter and

integrated picture

store (C)

For

camera package:

VKC-1326/WDDG1/2

The DSS (Digital Slow Shutter) can be activated or

deactivated using SW1. When the DSS is activated, the

number of pictures to be saved (x 8/x 16, integrated

picture store) can be set using SW2.

SW1 up (NOR) NOR (off) DSS deactivated, i.e. the dome camera acts like a normal

camera.

SW1 down (ON) DSS (ON) In this DIP switch position, the digital slow shutter is

activated (i.e. when the light intensity decreases, the slow

shutter is started (the video level rises).

SW2 up (SW1

must be at DSS)

x32 Digital slow shutter with 16 x picture store

SW2 down (SW1

must be at DSS)

x16 Digital slow shutter with 8 x picture store

DN, day/night

switch, IR mode

(C)

For

camera package:

VKC-1326WDDG1/2

Day/night switch SW1 can be set to ON (DN) or OFF (NOR).

The IR cut lter SW2 may be moved to ON (IR) or OFF

(NOR).

SW1 up (NOR) NOR (off) In the NOR (up) setting, the camera works like a normal

camera and does not change to night mode.

A B C

18

19

SW1 down to ON

(DN)

DN (on) In the ON setting, the day/night mode is deactivated and

the camera automatically switches between day and night

mode depending on the light intensity. If the light intensity

is less than half the video level, the camera switches to

night mode, removes the optic lter (to obtain a higher

video level) and switches to black/white mode.

In night mode, the camera uses realtime black/white

video and also absorbs IR light. When the light becomes

brighter again, the camera automatically changes back to

day mode, replaces the optic lter again and switches to

colour mode.

IR, IR operation

(C)

For

camera package:

VKC-1326/WDDG1/2

SW2 up (NOR) NOR The IR operation switch is a very special feature in

comparison with other cameras.

If the IR operation switch is set to NOR (up), the camera

switches from night to day mode and replaces the IR cut

lter if the video level exceeds a value of approximately

70 IRE.

This is the normal state and it is assumed that NO IR light

is used and a video level exceeding 70 IRE is reached with

natural light only.

SW2 down to ON

(IR)

IR (on) If the IR operation switch is set to IR (ON), the camera

switches from night to day mode and replaces the IR cut

lter as soon as a video level exceeding 85 IRE is reached.

This is the IR operation and it is assumed that IR lighting

is used and a video level exceeding 85 IRE is reached with

a combination of IR light and natural light.

The purpose of the IR operation switch is to prevent the

camera constantly switching between day and night mode.

18

19

Vertical

Phase

8 Position

DIP switch

D E

IRIS

LEVEL

Vertical

Phase

8 Position

Piano switch

IRIS

LEVEL

D, E For camera package:

VKC-1327/WDDG1/2

DIP switch

(SW)

Function DIP switch ON DIP switch OFF

SW 1

NT/LL

Synchronisation

Internal Line lock The synchronisation

changes automatically,

depending on the mains

voltage. However, if SW1

is set to ON at 24VAC,

the camera operates in

internal synchronisation

mode.

SW 2

ELC/ALC Electronic shutter

activated

Manual shutter (1/50sec).

Only when using a video

signal controlled lens.

SW 3

BLC Backlight compensation

activated.

Backlight compensation is

deactivated.

SW 4

AGC Turbo AGC turbo mode is

activated.

Normal AGC operation

SW 5

FL Flickerless Flicker-free operation

is activated. Electronic

shutter at 1/50sec

Flicker-free operation is

deactivated. For shutter

operation, see SW2.

Only when operated at

50Hz.

SW 6

Sharpness Sharpness Standard setting

SW 7

Day/night If the lighting is

insufcient, the camera

switches to night mode.

The camera constantly

operates in normal mode.

SW 8

IR mode The IR mode prevents

constant switching

between day and night

mode.

IR mode deactivated.

(Switches to B/W

operation)

20

21

Fault Reason Action

The system is not functioning. No power supply Check and remedy if applicable.

No picture Incorrect connection

alignment

Check and correct if applicable.

Check and connect correctly if applicable.

No signal

Grainy or broken image Video connection to camera

damaged

Check and connect correctly if applicable.

Increase lighting

Poor lighting

Weak, milky image Light from the side Change camera position or possibly eliminate light

by tilting the housing using the integrated sun roof

or by screening, e.g. with a board. Then correct the

tilted image by turning the camera bracket in the

housing.

Service Maintenance and instal-

lation

May only be carried out by authorised persons.

7. Troubleshooting and Rectication of Faults

8. Specications and Accessories

Cameras with 1/3” chip

Model VK-1320/WDDG1

VK-1320/WDDG2

VK-1318/WDDG1

VK-1318/WDDG2

VKC-1324/WDDG1

VKC-1324/WDDG2

VKC-1326/WDDG1

VKC-1326/WDDG2

VKC-1327/WDDG1

VKC-1327/WDDG2

EDP No.

91971 / 91972 91944 / 91897 91947 / 91948 91949 / 91954 91955 / 91956

Camera

B/W camera, stan-

dard resolution

B/W camera,

high resolution

Colour camera, high resolution

Description

Integrated varifocal lens Integrated

varifocal lens,

low speed shutter,

picture store

(DSS) up to 16x

integration

Integrated

varifocal lens,

DIP switch for

8 functions, IR

pivoting lter

Imager

1/3” Interline

Transfer CCD

1/3” Sony Super HAD Interline Transfer CCD

Active

picture

elements

Approx. 300,000,

(H) 512 x (V) 582

pixels

Approx. 440,000, (H) 752 x (V) 582 pixels

System

CCIR CCIR/PAL

Synchroni-

sation

Internal

Sensitivity

at 50%

video signal

0.14Lux at F1.2 2.1Lux at F2.0 /

0.75Lux at F1.2

0.6Lux at F1.2 0.005Lux at F1.2

(and with maxi-

mum integration)

B/W: 0.24Lux

at F1.2; Colour:

0.55Lux at F1.2

(w. AGC - normal)

20

21

Model VK-1320/WDDG1

VK-1320/WDDG2

VK-1318/WDDG1

VK-1318/WDDG2

VKC-1324/WDDG1

VKC-1324/WDDG2

VKC-1326/WDDG1

VKC-1326/WDDG2

VKC-1327/WDDG1

VKC-1327/WDDG2

EDP No.

91971 / 91972 91944 / 91897 91947 / 91948 91949 / 91954 91955 / 91956

Horizontal

resolution

380TV lines 600TV lines 480TV lines

Gain control

(AGC)

On (x) 28dB Normal, turbo

Automatic

shutter (AES)

1/50 to 1/100,000sec.

White balance

(AWB)

– Automatic

Backlight

compen-

sation (BLC)

Yes No Yes

Gamma

correction

0.45

Lens

F1.6-2.4/4-8mm

without iris

F2.0-2.8/4-8mm

without iris

F1.3-2.0 / 3.8-9.5mm

F1.3/F2.0-360/3.8-9.5mm

Horizontal

angle of view

63°-34° 65°-29°

Gland

WDDG2: 1x 1/2” glands (dummy plugs for 1/2” und 1/3” are included)

WDDG1: 2x 8mm holes with rubber glands

Cable

connection

Connection cable

with BNC and

DC jack

Multi-wire cable

with open ends

Connection cable

with BNC and DC

jack

Connection cable

with BNC and DC

jack

Connection cable

with BNC jack and

2 pin connector

Video output

1Vp-p, BAS, 75ohms 1Vp-p, FBAS, 75ohms 1Vp-p, BAS/FBAS,

75ohms

Operating

voltage

12VDC (±10%) 12V (9-18VDC) 12VDC / 24VAC

Power

consumption

Approx. 2W Approx. 1.4W Approx. 3W

Temperature

range

-10°C to +45°C -10°C to +50°C (operation)

Housing

version

Integrated version: WDDG1, for ceiling and wall mounting

Mounted version: WDDG2, for mounting on ceilings and walls

Housing

Aluminium cast with polycarbonate dome

Index

of protection

IP X5 (IP 65 with correct mounting, e.g. use of the included xing screws sealant and appropriate

grommets)

Dome

3mm polycarbonate – clear – with black internal cover and front glass, excellent durability

Dimensions

See dimensioned drawings

Weight

Approx. 750g

Accessories

supplied

WDDG2: Kit for mounting, 1/2” gland, dummy plugs, Torx key

WDDG1: Kit for mounting, Torx key

Accessories

EDP No. 70447, mains connector, 12VDC (for cameras with open connection cable ends)

EDP No. 70448, mains connector 230VAC/12VDC/1.0A (f. cameras w. plug type connection)

EDP No. 77779, mains connector 12VDC/0.5A

(UK version, f. cameras with open connection cable ends)

EDP No. 77772, power supply 12VDC/0.5A, desk version (f. cameras w. plug type connection)

EDP No. 70226, connection cable (cut goods)

22

23

Cameras with 1/4” chip

Model VKC-1414/WDDG1

VKC-1414/WDDG2

VKC-1413/WDDG1

VKC-1413/WDDG2

VKC-144/WDDG1

VKC-144/WDDG2

VKC-148/WDDG1

VKC-148/WDDG2

EDP No.

91945 / 91946 91895 / 91896 91893 / 91854 91894 / 91861

Camera

Colour camera, standard resolution Colour camera,

high resolution

Description

Integrated varifocal lens Integrated lens

Imager

1/4” Sony Super HAD Interline Transfer CCD

Active

picture elements

Approx. 290,000, 500 (H) x 582 (V) Approx. 440,000;

752 (H) x 582 (V)

System

CCIR/PAL

Synchronisation

Internal

Sensitivity at 50%

video signal

0.95Lux at F1.4

(measured) /

0.7Lux at F1.2

3,5Lux at F2.0 (measured) /

1.25Lux at F1.2

1.75Lux at F2.0

(measured) /

0.63Lux at F1.2

Horiz. resolution

330TV lines 380TV lines 470TV lines

Gain control (AGC)

28dB 41dB Can be switched

on and off

Automatic shutter

(AES)

1/50 to 1/100,000sec. Can be switched

on and off

White balance

(AWB)

Automatic Can be switched

on and off

Backlight compen-

sation (BLC)

Yes Can be switched

on and off

Gamma correction

Approx. 0.45

Lens

F1.6-360/3-6mm F2.0-2.7/2.6-5.6mm

without iris

F2.0/3.6mm

without iris

F2.0/2.9mm

without iris

Horizontal angle

of view

Approx. 65°-34° Ca. 69°-35° 52° 63°

Gland

WDDG2: 1x 1/2” glands (dummy plugs for 1/2” und 1/3” are included)

WDDG1: 2x 8mm holes with rubber glands

Cable connection

Connection cable

with BNC jack and

hollow connector

Multi-wire cable with open ends

Video output

1Vp-p, FBAS, 75Ohm

Operating voltage

9-18VDC 12VDC (±10%)

Power consumption

Approx. 1.5W

Temperature range

-10°C to +50°C (operation)

Housing

Aluminium cast with polycarbonate dome

Housing version

Integrated version: WDDG1, for ceiling and wall installation

Mounted version: WDDG2, for mounting on ceilings and walls

22

23

9. Dimensional Drawings

See page 44

Model VKC-1414/WDDG1

VKC-1414/WDDG2

VKC-1413/WDDG1

VKC-1413/WDDG2

VKC-144/WDDG1

VKC-144/WDDG2

VKC-148/WDDG1

VKC-148/WDDG2

EDP No.

91945 / 91946 91895 / 91896 91893 / 91854 91894 / 91861

Index of protection

WDDG2: (IP 65 with correct mounting, e.g. use of the included xing screws sealant and

appropriate grommets)

WDDG1: IP50

Dome

3mm polycarbonate – clear – with black internal cover and front glass, excellent durability

Dimensions

See dimensioned drawings

Weight

Approx. 750g

Accessories

supplied

WDDG2: Kit for mounting, 1/2” gland, dummy plugs, Torx key

WDDG1: Kit for mounting, Torx key

Accessories

EDP No. 70447, mains connector, 12VDC (for cameras with open connection cable ends)

EDP No. 70448, mains connector 230VAC/12VDC/1.0A (f. cameras w. plug type connection)

EDP No. 77779, mains connector 12VDC/0.5A

(UK version, f. cameras with open connection cable ends)

EDP No. 77772, power supply 12VDC/0.5A, desk version (f. cameras w. plug type connection)

EDP No. 70226, connection cable (cut goods)

Lenses (optional)

for the EDP No.

91893/91854 only

EDP No. 40072, F2.0/6mm 1/3” lens for board cameras

EDP No. 40061, F2.0/8mm 1/3” lens for board cameras

EDP No. 40065, F2.5/12mm 1/3” lens for board cameras

Page is loading ...

9. Maßzeichnungen – Dimensional drawings – Croquis – Medidas

Maße - Dimensions - Medidas: mm

WDDG1 WDDG2

86 ∅

52.5 ± 1

91.5 ± 1

40

8 ∅

85 ∅

64

86 ∅

91.5 ± 1

PT 3/4"

120

SLD Security & Communications

The Old Forge, Ockham Lane, Ockham, Surrey GU23 6PH England

Phone +44.1483225633 · Fax +44.1483225634

[email protected] · www.sld.co.uk

Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

in other languages

Related papers

Other documents