i3 International i3F417U User manual

Brand: i3 International

Model: i3F417U

Category: Security cameras

Type: User manual

i3F417U (with UTP Balun)

3-Axis Vandal Dome User Guide

CONTENTS

PRECAUTIONS

NOTES OF USE

CEILING MOUNT I

NSTALLATION

WALL MOUNT I

NSTALLATION

SPECIFICATIONS

WARNING:

Before attempting to connect or operate this product, read these instructions carefully.

Save this manual for future use.

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera.

Refer servicing to qualified personnel only.

PRECAUTIONS

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference, in which case users will be required to correct the

interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables

when connecting to computer or peripheral devices. Any changes

or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on top of the unit. It is

recommended that you note the serial number of this unit in the space

provided and retain this book as a permanent record of your purchase to

aid identication in the event of theft.

Model No.

Serial No.

Date of Purchase:

Power Supply

You can use either AC 24V or DC 12V power input. The camera automatically

detects the power. When connecting the transformer, be sure to connect each

lead to the appropriate terminal. Incorrect connection may cause malfunction

and/or damage to the video camera. You must ground the unit in order to avoid

an irregular voltage, which may be generated in the AC power cable and may

cause malfunction and/or damage to the video camera.

Operating or storage location

Avoid shooting very bright objects (such as light ttings) for an extended period.

Avoid operating or storing the unit in the following locations:

• Extremely hot or cold places (operating temperature: -10

C to +50

• Close to sources of strong magnetism

• Close to sources of powerful electromagnetic radiation, such as radios

or TV transmitters

• Close to humid or excessively dusty places

• Where exposed to mechanical vibrations

• Close to uorescent lamps or objects reecting light

• Under unstable light sources (may cause ickering)

Attaching the dome casing

Attach the dome casing with the screw provided.

Transportation

When transporting the camera, repack it as originally packed at the factory,

or in materials equal in quality.

Cleaning

• For maximum optical clarity, the dome cover must remain clean. Use a

soft, dry cloth to remove nger prints or dust from the dome cover.

• Use a blower to remove dust from the lens.

• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth

dampened with a small quantity of neutral detergent, then wipe dry.

• Do not use volatile solvents such as alcohol, benzene, or thinners, as

they may damage the surface nishes.

Ensuring Water Resistance

Wrap the connections (threads) between pipes with waterproof adhesive/tape to

prevent water/moisture from entering.

PRECAUTIONS

Using the Camera Outdoors

To prevent moisture from getting inside the casing, use sealant (e.g., silicon

sealant) to seal the following areas:

• The holes under the unit casing that is attached to a ceiling or wall.

• Conduit holes on the side and bottom of the unit casing. Seal using a water-

proof accessory.

• Joint surface of the camera casing gasket and unit casing.

Location and Function of Parts

456

NOTES OF USE

1. Unit casing

The unit casing is made of die-cast aluminum and has conduit holes on

the side and bottom.

2. Safety cord

The safety cord prevents the dome casing from falling. To avoid personal

injury and liability, do not remove the safety cord from the unit. If it is

necessary to remove the cord, remember to fasten the screws provided.

3. Zoom & Focus lever

Adjusts the camera range and focus. The lever itself is a screw and can be

removed. Turning this screw completely clockwise locks the position.

4. UTP-Unshield Twisted Pair (white/black wire)

Twisted Pair (TP) terminal (CAT.5E) for video signal. Usage of TP output

requires a TP receiver at the other end of the TP line.

5. Power connector (red/black wire)

Connects to the external power source. (DC12V/AC24V)

6. BNC connector

Connects to the VIDEO IN connector of the Monitor Video Connector

7. Level adjustment switch

Use to compensate for the Iris Level. Turn towards L (low)/ H (high) to make

the picture appear darker/brighter.

8. DIP Switches for Mode setting

BLC (Back Light Compensation). Factory setting: OFF

When switched ON, this function compensates the exposure for the scenes,

where the subject is lit from behind.

AGC (Automatic Gain Control). Factory setting: ON

This function automatically adjusts the picture in accordance with the subject

brightness.

DC/AES switch. Non-functional switch. Reserved for future development

Flickerless. Factory setting: OFF

When switched ON, this function reduces ickers on a NTSC/PAL cameras

used with 50Hz/60Hz power frequency.

NOTES OF USE

This camera features the SONY® CCD combined with SONY’s latest

advances in digital signal processing (DSP) technology to enable day/

night monitoring and surveillance applications, as well as effectively

handle other challenging lighting conditions including backlighting, bright

sunlight and deep shadows.

SONY CCD & DSP

Step 3:

Press the grip portion to

remove the mask and

rotate the main bracket to

adjust the pan angle.

CEILING MOUNT INSTALLATION

Ceiling Mount Installation

Step 1:

Adhere the guide pattern to the

installation surface. Drill one big

and three small holes, using the

template as a guide.

Step 2:

Install the camera onto the ceiling

and fasten securely using the

screws provided.

Ceiling Mount Installation (Continued)

CEILING MOUNT INSTALLATION

Step 4:

Loosen the screw on the main

bracket, adjust the tilt angle, then

tighten the screw to maintain

setting.

Step 6:

Return mask to its original position

on the camera. Screw the top cover

to the camera securely.

Step 5:

Adjust the camera zoom to a suitable

position.

WALL MOUNT INSTALLATION

Wall Mount Installation

Step 1:

Adhere the guide pattern to the

installation surface. Drill four

small holes for the plastic drywall

anchors.

Step 2:

Fasten the bottom casing to the

wall by securely tightening the four

screws provided.

Step 3:

Install the camera onto the bottom

casing and secure tightly with

screws.

WALL MOUNT INSTALLATION

Step 4:

Press the grip portion to remove

the mask and rotate the main

bracket to adjust the pan angle.

Step 5:

Loosen the screw on the main bracket,

adjust the tilt angle, then tighten the

screw to maintain setting.

Step 6:

Adjust the camera zoom to a suitable

position.

Wall Mount Installation (Continued)

WALL MOUNT INSTALLATION

Wall Mount Installation (Continued)

Step 7:

Return mask to its original position

on the camera.

Step 8:

Screw the top cover to the camera

securely.

SPECIFICATIONS

The specifications are subjects to be change without notice

Camera

Signal system NTSC PAL

Scanning system 2:1 Interlace

Sync system Internal

Scanning frequency (H) 15.734 KHz 15.625 KHz

Scanning Frequency (V) 59.94 Hz 50 Hz

Day & Night (IICR) Easy D/N ; Auto

Imaging area 4.9 mm x 3.7 mm

Image sensor 1/3” SONY CCD

Horizontal Resolution 560 TV lines

Effective pixels (HxV) 768 x 494 752 x 582

Lens f=2.8~10mm,4X, F1.3 vari-focal lens

Min. illumination 0.02 lux

(F1.3, AGC on, 10 IRE)

0.35 lux

(F1.3, AGC on, 50 IRE)

AGC, BLC, Flickerless ON/OFF

White balance Auto: (2500°K~9500°K)

S/N ratio > 50dB (AGC off)

View angle Horizontal:76.92°(wide) ~ 22.73°(tele), Vertical:56.89°(wide) ~

17.07°(tele)

Video output 1Vpp composite output, 75 ohm

Gamma correction 0.45

Weight 1150g (2.54 lbs) approx.

Dimensions 150mm x 132mm (5.91” x 5.20”)

Vandal Resistant 1000kg (2,204.62lbs) impact resistance

Environment

Operating temperature -10º ~ 50º C (14º~122º F)

Storage temperature -20ºC ~ 60ºC (-4º ~ 140º F)

Humidity 30% ~ 90% RH

Electrical

Power requirement 12 VDC/24 VAC ±10%

Power consumption 4.5W (max.)

UTP Yes - 300m (985 ft.)

Warranty

Product warranty 3 years

i³ INTERNATIONAL INC.

1.866.840.0004

www.i3international.com

Canada 780 Birchmount Road,

Unit 16, Scarborough,

ON, M1K 5H4

U.S.A. 440 Lawrence Bell Drive,

Suite 16, Williamsville

NY, 14221

i3 International i3F417U User manual

Brand: i3 International

Model: i3F417U

Category: Security cameras

Type: User manual

Download PDF

report

i3 International i3F417U User manual

i3 International i3F417U User manual

Related papers

Other documents