Airmar TDT1000 Quick Start Manuals

Type
Quick Start Manuals

Airmar TDT1000 is a portable, Bluetooth-enabled transducer diagnostic tester that allows boat owners, dealers, and installers to quickly and easily test the performance of transducers, right on the boat.

Airmar TDT1000 is a portable, Bluetooth-enabled transducer diagnostic tester that allows boat owners, dealers, and installers to quickly and easily test the performance of transducers, right on the boat.

©2018 Airmar Technology Corporation 17-632-01_rev03 TDT1000_QuickStart 11/01/18
As Airmar constantly improves its products, all specications are subject to change without notice. All Airmar products are designed
to provide high levels of accuracy and reliability, however they should only be used as aids to navigation and not as a replacement for
traditional navigation aids and techniques. Xducer ID® is a registered trademark and SensorCheck™ is a trademark of Airmar Technology
Corporation. Other company or product names mentioned in this document may be trademarks or registered trademarks of their
respective companies, which are not aliated with Airmar.
TDT1000 will not turn on
Make sure unit has been fully charged.
Conrm charging light is lit.
It may take a full charge cycle before the unit will power on.
SensorCheck app cannot nd/connect to the TDT1000
Make sure Bluetooth is LE. Older phones may not have Bluetooth LE.
Only one app/Bluetooth device can connect to TDT1000 at a time. Make sure
no other devices are already connected. Power o the TDT1000 and restart the
Bluetooth search.
Test results indicate the transducer is out of range, but I am not sure it is.
Consult the Owners Guide. Results may vary based on the test environment.
Vary the test environment and see if the results bring the transducer into range.
Verify that you are using the correct adapter cable.
If using the test block, ensure there is no air between block and transducer.
Training and support services can be found at the following:
Gemeco (USA) Airmar EMEA (Europe, Middle East, Africa)
Tel: 803-693-0777 Tel: +33.(0)2.23.52.06.48
email: sales@gemeco.com email: sales@airmar-emea.com
Troubleshooting
Download SensorCheck on the
App Store or Google Play
At the completion of the test, one of
two screens will appear. If the results are
In Range, email results tothe boat owner,
dealer, and/or installer (Screen A).
If the results are Out of Range, email test
results with your contact information to
tdt1000@airmar.com before removing or
replacing the transducer (Screen B).
Step 3
Review your results
Screen BScreen A
TDT1000
Transducer Diagnostic Tester
QUICK START GUIDE
Kit Includes
TDT1000
Adapter cable with terminal box for transducers with NO connector
Power charger with USB to Micro USBadapter
Carrying case
International wall-plug adapter kit
(UK, Australia, and Europe)
OEM adapter cables
(if purchased)
TDT Test Block
1. Power on the TDT1000. The LED will glow green.
2. Open the SensorCheck app on your device and connect
to the TDT1000 via Bluetooth.
3. Press the Start Test icon on the SensorCheck app
to begin the test.
NOTE: If the SensorCheck app does not connect to TDT1000, see
the back panel of this Quick Start Guide, Troubleshooting.
Step 2
Start the test
4. SensorCheck automatically checks for
Xducer ID® (Screen A). If found, the test
will begin.
If not found, youwill haveto enter the
information requested onthe screen
(Screen B).
1. Read the entire Owners Guide, review product specications,
andregister your product at www.airmar.com/tdt1000.
2. The SensorCheck™ app must be installed on a Bluetooth®
LE-enabled iOS or Android device to connect to the TDT1000.
CAUTION: The transducer must be connected to the TDT1000
through an OEM adapter cable. Do not connect the transducer directly to the TDT1000.
CAUTION: The transducer and OEM adapter cable must be connected to the
TDT1000 before starting a test. Do not connect or disconnect a transducer while
testing is in progress. Doing so may damage the TDT1000.
Before you start
Diagram 1
Screen BScreen A
transducer
battery-status
light (3)
Te
st in Progress
indicator light
Charging
indicator light
Power
indicator light
Function
indicator light
test cable
port
transducer
connector
transducer
adapter cable
(purchased separately)
cable
1. The transducer being tested must be done one of the following ways:
Installed in a boat while the boat is in the water.
Tested utilizing the TDT tester block.
2. Utilizing the correct OEM adapter cable (sold separately), connect the TDT1000 to the
transducer cable (Diagram 1). If the transducer does not have a connector, it must
be connected through the terminal box. Follow the color-coded instructions on the
terminal box.
Step 1
Prepare the transducer for testing
Available OEM Adapter Cables: Part Number
Furuno Adapter Cable, 10M - FU connector 33-1328-01
Furuno/Si-tex Adapter Cable, 8M - F (Fuji) connector 33-1327-01
Garmin Adapter Cable, 6M - A connector 33-1324-01
Garmin Adapter Cable, 8M - G connector 33-1325-01
Garmin Adapter Cable, 12M - G connector 33-1326-01
Koden Adapter Cable, 8M - A connector 33-1338-01
Lowrance Chirp Adapter Cable, dual 7FB - LR connector 33-1333-01
Lowrance Conventional Adapter Cable, 7FB - LR connector 33-1332-01
Mix & Match Adapter Cable, 1kW, 9F - A connector 33-1323-01
Mix & Match Adapter Cable, 600W, 5F - A connector 33-1389-01
Mix & Match Chirp Adapter Cable, 12M - MM connector 33-1390-01
Navico Adapter Cable, dual 9F - A connectors 33-1388-01
Navman Adapter Cable, 6M - A connector 33-1335-01
Simrad Adapter Cable, 7M - A connector 33-1334-01
Si-tex Adapter Cable, 8F - A connector 33-1337-01
Raymarine Adapter Cable, 6/9F - A connector 33-1330-01/1310-01
(Sense Resistor Ident.)
Raymarine Adapter Cable, 11M - LTW connector 33-1331-01/1312-01 (Sense Resistor Ident.)
Raymarine Adapter Cable, 8M - RR connector 33-1329-01/1311-01 (Sense Resistor Ident.)
Visit AIRMAR.COM/TDT1000 for the most updated OEM Adapter list.
1. Power on the TDT1000. The LED will glow green.
2. Open the SensorCheck app on your device and connect
to the TDT1000 via Bluetooth.
3. Press the Start Test icon on the SensorCheck app
to begin the test.
NOTE: If the SensorCheck app does not connect to TDT1000, see
the back panel of this Quick Start Guide, Troubleshooting.
Step 2
Start the test
4. SensorCheck automatically checks for
Xducer ID® (Screen A). If found, the test
will begin.
If not found, youwill haveto enter the
information requested onthe screen
(Screen B).
1. Read the entire Owners Guide, review product specications,
andregister your product at www.airmar.com/tdt1000.
2. The SensorCheck™ app must be installed on a Bluetooth®
LE-enabled iOS or Android device to connect to the TDT1000.
CAUTION: The transducer must be connected to the TDT1000
through an OEM adapter cable. Do not connect the transducer directly to the TDT1000.
CAUTION: The transducer and OEM adapter cable must be connected to the
TDT1000 before starting a test. Do not connect or disconnect a transducer while
testing is in progress. Doing so may damage the TDT1000.
Before you start
Diagram 1
Screen BScreen A
transducer
battery-status
light (3)
Te
st in Progress
indicator light
Charging
indicator light
Power
indicator light
Function
indicator light
test cable
port
transducer
connector
transducer
adapter cable
(purchased separately)
cable
1. The transducer being tested must be done one of the following ways:
Installed in a boat while the boat is in the water.
Tested utilizing the TDT tester block.
2. Utilizing the correct OEM adapter cable (sold separately), connect the TDT1000 to the
transducer cable (Diagram 1). If the transducer does not have a connector, it must
be connected through the terminal box. Follow the color-coded instructions on the
terminal box.
Step 1
Prepare the transducer for testing
Available OEM Adapter Cables: Part Number
Furuno Adapter Cable, 10M - FU connector 33-1328-01
Furuno/Si-tex Adapter Cable, 8M - F (Fuji) connector 33-1327-01
Garmin Adapter Cable, 6M - A connector 33-1324-01
Garmin Adapter Cable, 8M - G connector 33-1325-01
Garmin Adapter Cable, 12M - G connector 33-1326-01
Koden Adapter Cable, 8M - A connector 33-1338-01
Lowrance Chirp Adapter Cable, dual 7FB - LR connector 33-1333-01
Lowrance Conventional Adapter Cable, 7FB - LR connector 33-1332-01
Mix & Match Adapter Cable, 1kW, 9F - A connector 33-1323-01
Mix & Match Adapter Cable, 600W, 5F - A connector 33-1389-01
Mix & Match Chirp Adapter Cable, 12M - MM connector 33-1390-01
Navico Adapter Cable, dual 9F - A connectors 33-1388-01
Navman Adapter Cable, 6M - A connector 33-1335-01
Simrad Adapter Cable, 7M - A connector 33-1334-01
Si-tex Adapter Cable, 8F - A connector 33-1337-01
Raymarine Adapter Cable, 6/9F - A connector 33-1330-01/1310-01
(Sense Resistor Ident.)
Raymarine Adapter Cable, 11M - LTW connector 33-1331-01/1312-01 (Sense Resistor Ident.)
Raymarine Adapter Cable, 8M - RR connector 33-1329-01/1311-01 (Sense Resistor Ident.)
Visit AIRMAR.COM/TDT1000 for the most updated OEM Adapter list.
1. Power on the TDT1000. The LED will glow green.
2. Open the SensorCheck app on your device and connect
to the TDT1000 via Bluetooth.
3. Press the Start Test icon on the SensorCheck app
to begin the test.
NOTE: If the SensorCheck app does not connect to TDT1000, see
the back panel of this Quick Start Guide, Troubleshooting.
Step 2
Start the test
4. SensorCheck automatically checks for
Xducer ID® (Screen A). If found, the test
will begin.
If not found, youwill haveto enter the
information requested onthe screen
(Screen B).
1. Read the entire Owners Guide, review product specications,
andregister your product at www.airmar.com/tdt1000.
2. The SensorCheck™ app must be installed on a Bluetooth®
LE-enabled iOS or Android device to connect to the TDT1000.
CAUTION: The transducer must be connected to the TDT1000
through an OEM adapter cable. Do not connect the transducer directly to the TDT1000.
CAUTION: The transducer and OEM adapter cable must be connected to the
TDT1000 before starting a test. Do not connect or disconnect a transducer while
testing is in progress. Doing so may damage the TDT1000.
Before you start
Diagram 1
Screen BScreen A
transducer
battery-status
light (3)
Te
st in Progress
indicator light
Charging
indicator light
Power
indicator light
Function
indicator light
test cable
port
transducer
connector
transducer
adapter cable
(purchased separately)
cable
1. The transducer being tested must be done one of the following ways:
Installed in a boat while the boat is in the water.
Tested utilizing the TDT tester block.
2. Utilizing the correct OEM adapter cable (sold separately), connect the TDT1000 to the
transducer cable (Diagram 1). If the transducer does not have a connector, it must
be connected through the terminal box. Follow the color-coded instructions on the
terminal box.
Step 1
Prepare the transducer for testing
Available OEM Adapter Cables: Part Number
Furuno Adapter Cable, 10M - FU connector 33-1328-01
Furuno/Si-tex Adapter Cable, 8M - F (Fuji) connector 33-1327-01
Garmin Adapter Cable, 6M - A connector 33-1324-01
Garmin Adapter Cable, 8M - G connector 33-1325-01
Garmin Adapter Cable, 12M - G connector 33-1326-01
Koden Adapter Cable, 8M - A connector 33-1338-01
Lowrance Chirp Adapter Cable, dual 7FB - LR connector 33-1333-01
Lowrance Conventional Adapter Cable, 7FB - LR connector 33-1332-01
Mix & Match Adapter Cable, 1kW, 9F - A connector 33-1323-01
Mix & Match Adapter Cable, 600W, 5F - A connector 33-1389-01
Mix & Match Chirp Adapter Cable, 12M - MM connector 33-1390-01
Navico Adapter Cable, dual 9F - A connectors 33-1388-01
Navman Adapter Cable, 6M - A connector 33-1335-01
Simrad Adapter Cable, 7M - A connector 33-1334-01
Si-tex Adapter Cable, 8F - A connector 33-1337-01
Raymarine Adapter Cable, 6/9F - A connector 33-1330-01/1310-01
(Sense Resistor Ident.)
Raymarine Adapter Cable, 11M - LTW connector 33-1331-01/1312-01 (Sense Resistor Ident.)
Raymarine Adapter Cable, 8M - RR connector 33-1329-01/1311-01 (Sense Resistor Ident.)
Visit AIRMAR.COM/TDT1000 for the most updated OEM Adapter list.
©2018 Airmar Technology Corporation 17-632-01_rev03 TDT1000_QuickStart 11/01/18
As Airmar constantly improves its products, all specications are subject to change without notice. All Airmar products are designed
to provide high levels of accuracy and reliability, however they should only be used as aids to navigation and not as a replacement for
traditional navigation aids and techniques. Xducer ID® is a registered trademark and SensorCheck™ is a trademark of Airmar Technology
Corporation. Other company or product names mentioned in this document may be trademarks or registered trademarks of their
respective companies, which are not aliated with Airmar.
TDT1000 will not turn on
Make sure unit has been fully charged.
Conrm charging light is lit.
It may take a full charge cycle before the unit will power on.
SensorCheck app cannot nd/connect to the TDT1000
Make sure Bluetooth is LE. Older phones may not have Bluetooth LE.
Only one app/Bluetooth device can connect to TDT1000 at a time. Make sure
no other devices are already connected. Power o the TDT1000 and restart the
Bluetooth search.
Test results indicate the transducer is out of range, but I am not sure it is.
Consult the Owners Guide. Results may vary based on the test environment.
Vary the test environment and see if the results bring the transducer into range.
Verify that you are using the correct adapter cable.
If using the test block, ensure there is no air between block and transducer.
Training and support services can be found at the following:
Gemeco (USA) Airmar EMEA (Europe, Middle East, Africa)
Tel: 803-693-0777 Tel: +33.(0)2.23.52.06.48
email: sales@gemeco.com email: sales@airmar-emea.com
Troubleshooting
Download SensorCheck on the
App Store or Google Play
At the completion of the test, one of
two screens will appear. If the results are
In Range, email results tothe boat owner,
dealer, and/or installer (Screen A).
If the results are Out of Range, email test
results with your contact information to
tdt1000@airmar.com before removing or
replacing the transducer (Screen B).
Step 3
Review your results
Screen BScreen A
TDT1000
Transducer Diagnostic Tester
QUICK START GUIDE
Kit Includes
TDT1000
Adapter cable with terminal box for transducers with NO connector
Power charger with USB to Micro USBadapter
Carrying case
International wall-plug adapter kit
(UK, Australia, and Europe)
OEM adapter cables
(if purchased)
TDT Test Block
©2018 Airmar Technology Corporation 17-632-01_rev03 TDT1000_QuickStart 11/01/18
As Airmar constantly improves its products, all specications are subject to change without notice. All Airmar products are designed
to provide high levels of accuracy and reliability, however they should only be used as aids to navigation and not as a replacement for
traditional navigation aids and techniques. Xducer ID® is a registered trademark and SensorCheck™ is a trademark of Airmar Technology
Corporation. Other company or product names mentioned in this document may be trademarks or registered trademarks of their
respective companies, which are not aliated with Airmar.
TDT1000 will not turn on
Make sure unit has been fully charged.
Conrm charging light is lit.
It may take a full charge cycle before the unit will power on.
SensorCheck app cannot nd/connect to the TDT1000
Make sure Bluetooth is LE. Older phones may not have Bluetooth LE.
Only one app/Bluetooth device can connect to TDT1000 at a time. Make sure
no other devices are already connected. Power o the TDT1000 and restart the
Bluetooth search.
Test results indicate the transducer is out of range, but I am not sure it is.
Consult the Owners Guide. Results may vary based on the test environment.
Vary the test environment and see if the results bring the transducer into range.
Verify that you are using the correct adapter cable.
If using the test block, ensure there is no air between block and transducer.
Training and support services can be found at the following:
Gemeco (USA) Airmar EMEA (Europe, Middle East, Africa)
Tel: 803-693-0777 Tel: +33.(0)2.23.52.06.48
email: sales@gemeco.com email: sales@airmar-emea.com
Troubleshooting
Download SensorCheck on the
App Store or Google Play
At the completion of the test, one of
two screens will appear. If the results are
In Range, email results tothe boat owner,
dealer, and/or installer (Screen A).
If the results are Out of Range, email test
results with your contact information to
tdt1000@airmar.com before removing or
replacing the transducer (Screen B).
Step 3
Review your results
Screen BScreen A
TDT1000
Transducer Diagnostic Tester
QUICK START GUIDE
Kit Includes
TDT1000
Adapter cable with terminal box for transducers with NO connector
Power charger with USB to Micro USBadapter
Carrying case
International wall-plug adapter kit
(UK, Australia, and Europe)
OEM adapter cables
(if purchased)
TDT Test Block
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Airmar TDT1000 Quick Start Manuals

Type
Quick Start Manuals

Airmar TDT1000 is a portable, Bluetooth-enabled transducer diagnostic tester that allows boat owners, dealers, and installers to quickly and easily test the performance of transducers, right on the boat.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI