Panasonic TYWK42PV2W Operating instructions

Plasma display wall hanging bracket

(Vertical mounting type)

Fitting Instructions

Before commencing work, carefully read these Instructions and the Manual

for the wide plasma display to ensure that fitting is performed correctly.

(Please save these instructions. You may need them when maintaining or moving the bracket.)

Wandhalterung zum Anbringen des Plasmadisplays

(Typ für vertikale Anbringung)

Anleitung zur Anbringung

Vor der Ausführung lesen Sie bitte diese Anleitung und die Bedienungsanleitung für

das Plasmadisplay sorgfältig durch, damit die Anbringung richtig ausgeführt wird.

(Bitte bewahren Sie diese Anleitung auf. Sie kann bei der Wartung oder der

erneuten Anbringung der Halterung benötigt werden.)

Muurbevestigingssteun voor plasmascherm (voor

verticale montage)

Montage-instructies

Lees deze installatiehandleiding en de bedieningshandleiding voor het breedbeeld-plasmascherm

zorgvuldig door voordat u begint, zodat de montagewerkzaamheden op de juiste wijze worden uitgevoerd.

(Bewaar deze handleiding. U hebt de handleiding weer nodig wanneer u de

bevestigingssteun verwijdert of verplaatst.)

Staffa per montaggio alla parete dello schermo al

plasma (tipo per montaggio verticale)

Istruzioni per il montaggio

Prima di iniziare il montaggio leggere attentamente queste istruzioni ed il manuale

dello schermo al plasma allargato per poter procedere al montaggio in modo corretto.

(Conservare poi queste istruzioni che si renderanno necessarie per la

manutenzione e l’eventuale spostamento della staffa.)

Applique de fixation au mur

(type pour montage vertical)

Instructions de montage

Avant de commencer le travail, lisez attentivement ces instructions ainsi que le mode

d'emploi de l'écran large à plasma de manière à réaliser un montage convenable.

(Conservez soigneusement les présentes instructions. Vous pouvez en avoir

besoin pour effectuer un entretien ou si vous désirez déplacer l'applique.)

Soporte para colgar la pantalla de plasma en una

pared (Tipo de montaje vertical)

Instrucciones de instalación

Antes de empezar el trabajo, lea atentamente estas instrucciones y el manual

de la pantalla panorámica de plasma para asegurar una instalación correcta.

(Guarde estas instrucciones. Podrá necesitarlas cuando haga trabajos de

mantenimiento o mueva el soporte.)

Väggupphängningshållare för plasmaskärm

(vertikal monteringstyp)

Monteringsanvisningar

Innan arbetet påbörjas ska du noga läsa dessa anvisningar och bruksanvisningen

som medföljer plasmaskärmen för att försäkra att arbetet utförs på rätt sätt.

(Bevara dessa anvisningar. Du kan behöva anlita dem på nytt för underhåll

eller flyttning av hållaren.)

Vægophæng til plasmaskærm

(Type til lodret montering)

Opsætningsinstruktioner

Før arbejdet påbegyndes, skal De omhyggeligt læse disse instruktioner og betjeningsvejledningen

til widescreen-plasmaskærmen for at sikre at opsætningsarbejdet udføres korrekt.

(Gen disse instruktioner. De kan få brug for dem ved vedligeholdelse, eller

hvis ophænget skal flyttes.)

TY-WK42PV2W

Model No.

English

Deutsch

Nederlands

Italiano

Français

Español

Svenska

Dansk

TQZH485

English

22

English

2

WARNING

Fitting work and connection equipment expansion should never be done by any other

than a qualified installation specialist.

• Incorrect fitting may cause equipment to fall, resulting in injury.

Include a safety factor when considering the strength of the proposed fitting location.

• If strength is not sufficient the equipment may fall, resulting in injury.

When expanding connection equipment, be sure to prevent lock release.

• This may cause injury.

Do not fit at a location that cannot bear the load.

• If the fitting location lacks sufficient strength the equipment may fall.

CAUTION

Do not fit at any locations subject to humidity, dust, smoke, steam or heat.

• This may have an adverse effect on the plasma TV and cause fire or electric shock.

The work of fitting or removing the plasma TV must be performed by at least two people.

• The plasma TV may fall and cause injury.

Do not fit facing upwards, sideways or upside down.

• This may cause heat to build up inside the plasma TV unit, resulting in a fire.

Provide spacing around the plasma TV of at least 100 mm (3

15

/16 inches ) to the top and

right side, at least 300 mm (11

13

/16 inches ) to the left side, at least 60 mm (2

23

/64 inches )

to the bottom and at least 42 mm (1

21

/32 inches ) to the rear.

• The plasma TV unit has air blow holes on the top, and air suction holes on the bottom and rear.

Covering these may result in a fire.

1) Exercise care when selecting the location for the TV because it may discolor or deform due to light or heat if it

is placed where it is exposed to direct sunlight, or near a heater.

2) Upkeep

Wipe with a dry cloth. If the unit is extremely soiled, first wipe off soiling with a neutral detergent diluted in

water, and then wipe with a dry cloth. Do not use cleaners such as benzene, thinner or furniture wax because

they may cause paint peeling. (If using a chemical wiping cloth, follow any precautions included.)

3) Do not affix adhesive tape or stickers to the product. Either may stain the wall hanging bracket or surface of the

wiring cover for close-to-the-wall installation.

Requests regarding handling

Safety precautions

[Always follow these precautions]

3

English

Components

Wall hanging bracket . . . x1

Insulation spacers . . . x4

Dished toothed washers . . . x4

Allen wrench (included tool)

. . . x1

Unit fastening screws (M5-35)

. . . x2

Allen head countersunk screws

(M8-55) . . . x4

TY-WK42PV2W Wall hanging bracket (Vertical mounting type)

Precautions for wall hanging bracket fitting

♦ The wall hanging bracket is for use in attaching a plasma TV unit to a vertical wall for viewing. Do not fit to

any surface other than a vertical wall.

♦ The equipment has a lock mechanism on the left side, so provide at least 300 mm (11

13

/

16 inches ) of

space from the wall surface.

♦ To ensure correct plasma TV performance and prevent trouble, do not fit at any of the following locations.

• Near sprinklers or fire/smoke detectors

• Where there is a risk of exposure to vibration or impact

• Near high-voltage wires or dynamic power supplies

• Locations exposed to air blown from heating equipment

♦ Fit using techniques suited to the structure and materials of the fitting location.

♦ Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc.)

for fitting the bracket to the wall.

♦ Fit so there is no contact between the attachment screws or power cord and any metal inside the wall.

♦ For the TV power supply plug, use a power supply outlet that can be reached easily.

♦ Ensure good air flow so that the equipment ambient temperature does not exceed 40°C. Failure to do this

may cause heat to build up inside the plasma TV, resulting in malfunction.

44

English

Fitting procedure

(

TY

-

WK42PV2W

)

1. Confirm the strength of the proposed fitting location

The weight of the wall hanging bracket is approximately 6 kg (13 Ib.). The plasma TV unit attached

to the wall hanging bracket weighs approximately 29.5 (65 Ib.) to 35 kg (77 Ib.).

Check the wall strength at the 6 attachment locations by referring to the dimension drawing of the

wall hanging bracket (given below), and provide adequate reinforcement if strength is not sufficient.

2. Fit wall hanging bracket to wall

• Fit so that the arrow marks on the wall hanging bracket point upward.

• If the wall consists of a material such as concrete and bolts or nuts must be embedded beforehand,

determine the hole positions by aligning using the actual wall hanging bracket, or calculate hole positions

based on the dimension drawing, and then embed "M6" bolts or nuts.

When embedding bolts, locate so that the bolts protrude from the wall

by 10 mm

(

25

/64 inches

)

to 15 mm

(

19

/32 inches

)

.

Fitting procedure

(1) Fasten the screw at the top center hole first.

(2) Using a level, correct any bracket inclination, and then fasten screws

at the remaining 5 locations.

• There are 22 holes in the wall hanging bracket. If the wall material is wood, and adequate attachment

strength cannot be ensured by fastening at the 6 points at right, use as many spare holes as necessary.

However, exercise care because some wall materials may crack if screws are located too close together.

The following dimensions are important. Do not fit at any location where these dimensions cannot be

secured.

• Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc.)

for fitting the bracket to the wall.

Display outer profile

320

(

12

19

/32

)

11.0

(

7

/16

)

415

(

16

11

/32

)

C

B

370

(

14

9

/16

)

22.5

(

57

/64

)

775

(

30

33

/64

)

A

735

(

28

15

/16

)

660

(

25

63

/64

)

Wall attachment holes

(at 6 points)

Wall hanging bracket unit

Dimensions of clearance required

around wall hanging bracket

* Provide spacing for the plasma TV of at least 100 mm (11

13

/16 inches ) to the top and right side, at

least 300 mm (3

15

/16 inches ) to the left side, at least 60 mm (2

23

/64 inches ) to the bottom and at

least 42 mm (1

21

/32 inches ) to the rear.

Note

Unit: mm (inches)

Notes

AB

C

For 37-inch

For 42-inch

1070 (42

1

/

8

)

1170 (46

1

/

16

)

596 (23

15

/

32

)

656 (25

53

/

64

)

120 ( 4

47

/

64

)

150

( 5

29

/

32

)

5

English

3. Prepare the plasma TV

Fit the insulation spacers to the plasma TV.

Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and

follow the procedure below.

4.

Fit and fasten the plasma TV unit to the wall hanging

bracket

Caps

Flathead

screwdriver

(1) Using a flathead screwdriver,

remove the caps (x4) from the

plasma TV.

(2)

At the points where the caps have

been removed, fit the included Allen

head countersunk screws, dished

toothed washers and insulation

spacers (x4 each) as indicated in

the diagram at left. Fasten with the

included Allen wrench.

Allen head countersunk screw

Dished toothed washer

Insulation spacer

Allen wrench

Upper notchUpper notch

Lower hole

Insulation

spacer

(1)

(3)

(2)

Screw securing

hole for plasma

TV unit fastening

Screw for plasma

TV unit fastening

Wall hanging

bracket

Wall

Insulation spacer

Plasma TV

•

Always fit the unit fastening screws to ensure that the plasma TV unit

cannot be accidentally dislodged from the wall hanging bracket.

Note

6. Removal of plasma TV unit

Removal procedure

(1) Remove the screws for unit fastening (1 each on the left and

right) that are fitted to the wall hanging bracket sides.

(2) While lifting the bottom of the plasma TV unit, pull it towards

yourself.

(3) When the lower insulation spacers are freed, keep lifting upward.

• Always fit the red screws for open/close fastening to ensure that

the plasma TV unit cannot be accidentally dislodged.

Note

Wall

Wall handing

bracket

Fitting hole for red screw

for open / close fastening

Red screw for

open / close

fastening

Insulation spacer

Wall

(3)

(2)

Wall

hanging

bracket

(1)

Screw for

plasma TV

unit

fastening

(1)

Screw for

plasma TV

unit

fastening

5. Fasten wall hanging bracket

procedure

(1) After wiring, remove the red screw for open/close fastening (on

the left side), lift the TV unit towards yourself once, and then

slowly lower it. The lock will release.

(2) Securely tighten the red screws for open/close fastening (1 each

on the left and right) on the sides of the wall hanging bracket.

Fitting procedure

(1) Locate the insulation spacers on the top of the

plasma TV unit into the notch on the top of the

wall hanging bracket, and slide down.

(2) Lift the plasma TV unit a little, insert the bottom

insulation spacers into the holes on the bottom of

the wall hanging bracket, and slide the unit down.

(3) Attach securely using the included unit fastening

screws (1 each for left and right).

English

6

Warranty

Panasonic Consumer Electronics Company

Division of Matsushita Electric Corporation

of America

One Panasonic Way

Secaucaus, NJ

07094

RACKS AND STANDS

Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the

warrantor” ), will replace parts in case of defects in materials or workmanship, free of change, in the USA or

Puerto Rico, for ten (10) days from the date of the original purchase.

In-warranty parts in the USA can be obtained during the warranty period be contacting:

Panasonic Services Company (PASC)

20421 84th Avenue South

Kent, Washington 98032

Tel.:1-800-833-9626

Fax.:1-800-237-9080

(6 am to 5 pm Monday-Friday; 6 am to 10:30 am Saturday; PST)

Service in Puerto Rico can be obtained during the warranty period by calling the telephone number listed above.

This warranty is extended only to the original purchaser. A purchase receipt or other proof of the original

purchase is required for replacement parts under the warranty.

This warranty only covers failures due to materials and workmanship and does not cover normal wear. The

warranty does not cover damages which occurred in shipment or failures which result from accidents, misuse,

abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustments, improper maintenance,

alteration, line power surge, lightning damage, modification,or commercial use, such as hotel, office,

restaurant, or other business or rental use of the product, or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

PANASONIC SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE RESULTING

FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL

EXPRESS AND IMPLIED WARRANTIES. INCLUDING THE WARRANTIES OF MERCHANTABILITY, ARE

LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on

how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

If a problem with this product develops during or after the warranty period, you may contact your dealer or call

the number listed above.

If the problem is not handled to your satisfaction, then write to the Customer Satisfaction Center at the

Panasonic Consumer Electronics Company address indicated above.

Panasonic Sales Company, Division of

Matsushita Electric of Puerto Rico, Inc.

AVE. 65 de Infanteria, Km 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

Page is loading ...

Printed in Japan

SS

0503A0053

(

MBS

)

(

Recycled paper

)

Matsushita Electric Industrial Co., Ltd

Web Site : http://www.panasonic.co.jp/global/

Panasonic TYWK42PV2W Operating instructions

Panasonic TYWK42PV2W Operating instructions

in other languages

Related papers

Other documents