No Brand CKG5060S User manual

Mixed fuel cooker

INSTRUCTION BOOK

CKG5060W

CKG5060S

A

U

3

Important Safety Information

These warnings are provided in the interest of safety. You MUST read

them carefully before installing or using the appliance.

Keep this instruction book for future reference and ensure it is passed on

to any new owner.

This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

Installation

• The work of installation must

be carried out by competent and

qualified installers according

to the regulations in force.

• The appliance must be installed

at a minimum distance of 50 cm

from curtains or other combustible

material.

• Any modifications to the domestic

electric mains, which may be

necessary for the installation of the

appliance, should only be carried

out by qualified electrician.

• This cooker is heavy. Take care

when moving it.

• Remove all packaging before using

the cooker.

• Ensure that the electrical supply

complies with the type stated

on the rating plate, located

near the gas supply pipe.

• It is dangerous to modify, or

attempt to modify, the

characteristics of this appliance.

• This appliance cannot be

positioned on a base.

• If the supply cord is damaged, it

shall be replaced by a special

cord or assembly available from

Authorised Electrolux Service Centre.

• The NON-TIP DEVICE must be

fitted according to instructions to

prevent the cooker from tipping,

for example by a child climbing

onto the open oven door.

Child Safety

• This appliance has been designed

for use by adults. Supervise

children to ensure they do not

attempt to play with it.

• This appliance is not intended for

use by young children of infirm

persons unless they have been

adequately supervised to ensure

they can use the appliance safely.

• The cooker gets hot when it is in

use and retains heat for a long

period after use. Children should

be kept away until it has cooled.

• Children can also injure

themselves by pulling pans or

pots off the cooker, they should

be supervised at all times to

ensure their safety.

• Burners, plates, grills and pans

remain hot for a long time after

being switched off. Supervise

children at all times when in use

paying attention that they do not

touch surfaces or remain in the

vicinity of the appliance when in

use or when not completely

cooled.

4

During use

• This cooker is intended for domestic

cooking only. It is not designed for

commercial or industrial purposes.

This appliance is not connected to

a combustion products evacuation

device. It shall be installed and

connected in accordance with

current installation regulations.

Particular attention shall be given

to the relevant requirements

regarding ventilation.

• When in uses a gas cooker will

produce heat and moisture in the

room in which it has been

installed. Ensure there is a

continuous air supply, keeping air

vents in good condition or

installing a cooker hood with a

venting hose.

• Ensure that air can circulate

around the gas appliance. Poor

ventilation can produce a lack of

oxygen.

• Do not use this cooker if it is in

contact with water. Do not operate

the cooker with wet hands.

• Always grill with the oven door

closed.

• The grill pan will become hot

during use, always use oven

gloves when removing or

replacing a hot grill pan.

• During use the appliance

becomes hot. Care should be

taken to avoid touching heating

elements inside the oven.

• DO NOT store or use gasoline or

other flammable vapours, liquids

or items in the vicinity of this or

any other appliance.

• Do not spray aerosols in the

vicinity of this appliance while

it is in operation.

• To facilitate ignition, light the

burner before placing the pan

on the grill.

• After having lit the burner check

that the flame is regular.

• Always lower the flame or turn it

off before removing the pan.

• Unstable or deformed pans

should not be placed on the

burners in order to avoid

accidents caused by upsetting or

boiling over.

• Ensure the control knobs are in

the ‘OFF’ position when not in use.

• When using other electrical

appliances, ensure the cable

does not come into contact with

the hot surfaces of the cooker.

• Unstable or misshapen pans

should not be used on the hob

hotplates as unstable pans can

cause an accident by tipping or

spillage.

• Never leave the cooker

unattended when cooking with

oil and fats.

• This cooker should be kept

clean at all times. A build-up of

fats or foodstuffs could result in

a fire.

• Only clean this oven in

accordance with the instructions.

• In case of repairs, do not attempt

to correct yourself. Repairs

carried out by unqualified persons

can cause damage. Contact the

nearest Assistance Centre and

use only original spare parts.

5

• WARNING – Ensure that the

appliance is switched off before

replacing the lamp to avoid the

possibility of electric shock.

• Always stand back from the oven

when opening the oven door, to

allow any build-up of steam or heat

to release.

• • Where this appliance is installed

in marine craft or in caravans, it

shall NOT be used as a space

heater.

• Always ensure that the oven vent,

which is located at the centre back

of the hob, is left unobstructed to

ensure ventilation of the oven

cavity.

• Perishable food, plastic items and

aerosols may be affected by heat

and should not be stored above the

cooker.

• Before maintenance or cleaning

disconnect the appliance and allow

cooling.

• Never use steam or high-pressure

steam cleaners to clean the

appliance.

• Do no store flammable materials

(e.g. aerosols, plastic aprons,

paper baking sheets etc) in the

warming drawer, it is only intended

for warming of plates and baking

trays.

• Be careful when removing items

from the warming drawer, as they

may be hot.

Service

• This cooker should only be

repaired or serviced by an

authorised Electrolux Service

Engineer and only genuine

approved spare parts should be

used.

Environmental Information

• After installation, please

dispose of the packaging with

due regard to safety and the

environment.

• When disposing of an old

appliance, make it unusable, by

cutting off the cable.

Your safety is of paramount

importance. Therefore, if you are

unsure about any of the meanings

of these WARNINGS, contact the

Customer Care Department.

These instructions are only valid

in the country whose symbol

appears on this instruction’s

cover.

This product should not be treated

as household waste. Instead it

should be handed over to the

applicable collection point for the

recycling of electrical and

electronic equipment. By ensuring

this product is disposed of

correctly, you will help prevent

potential negative consequences

for the environment and human

health, which could otherwise be

caused by inappropriate waste

handling of this product. For more

detailed information about recycling

of this product, please contact your

local city office, your household

waste disposal service or the shop

where you purchased the product.

6

Contents

Instructions for the Installer

Technical features

Location

The safety equipment

Installation

Adaptation to different type of gas

Electrical connections

Instructions for the User

Use and care

Use of appliance

Before the first use of the oven

Electric oven

Oven function control knob

Using the Conventional Oven

Hints and Tips

Grilling

Using the Fan Oven

Defrosting

Oven Cooking Chart

Roasting/Grilling Chart

Using the Hob

Maintenance and Cleaning

Oven bulb replacement

Something Not Working

Electrolux Warranty

7

8

9

11

13

16

18

19

20

21

22

23

24

25

26

30

33

34

36

Guide to Use the Instructions

The symbols below will guide you when

reading the instruction book

Safety instructions

Step by Step Operation

Advice and recommendations

Environmental Information

7

Instructions for the Installer

Technical features

Dimensions Height

Width

Depth

Oven Capacity

900 mm

500 mm

600 mm

45 l

Natural Gas

(1.00kPa)

U-LPG,

(2.60kPa)

Front Left Rapid 10.5 10.5

Back Left Aux 4.2 4.0

Front Right Semi-rapid 7.0 6.5

Back Right Semi-rapid 7.0 6.5

Hob

Total 28.7 27.5

Oven Top element

Bottom element

Grill element

Convection fan

Light in the oven

Cleaning

1000 W

925 W

1925 W

60 W

Lamp 25W type E14

manual

Total oven rating 1960 W

Supply Rated voltage

Rated frequency

230-240 V

50 Hz

Accessories Oven grid (2 pieces)

Roasting tray + roasting grid

Total cooker rating

1960,6 W

This appliance is manufactured

according to the following EEC directives:

73/23/EEC; 90/683 EEC; 89/336/EEC;

93/68/EEC; 90/396 EEC, current edition.

8

Location

Qualified tradespersons must

carry out installation work on the

cooker. The cooker is heavy.

Certain edges and corners, which

will not normally be exposed, may

be sharp. USE GLOVES when

moving the cooker.

Before installing the cooker, you

should check that its dimensions

correspond to the rest of your kitchen

units. Measure the height of the

worktop from floor to top surface of

the worktop, and the cooker depth

from the wall to the front edge of the

cooker (see picture). The cooker

must also be installed in conformity

with the following standards.

If a 10A power socket or hard wiring

is required for installation, a licenced

electrician must install it.

Carry out installation as

described in the Installation

Requirement chapter – paragraph

2.4 of AG101-2000.

Gas installation must be carried out by

a qualified gas fitter in accordance with

AG101-2000. Choose a location free of

draughts and open doors and clear of

combustible materials or other fire

hazards such as curtains, etc.

The location should ensure

convenience of operation and service.

Any adjacent cabinets or walls must

not exceed the cooker’s sides height

(see fig.).

The cooker may be located in a

kitchen or dining room, but not in a

bathroom or shower room. The

levelling feet fitted to the appliance

can be adjusted to achieve a nominal

height to hotplate of 900mm + 10mm.

min

600

max

400

min

570

690

500

150

The cooker should be

installed only on the floor, it is

not suitable for installation on a

base.

9

The safety equipment

Leveling the cooker

The appliance is provided with

adjustable small feet placed in the

back and front corners of the base.

Never pull the appliance by the oven

handle.

By adjusting the small feet it is

possible to change the height of the

appliance so as to ensure a better

leveling with other surfaces and a

uniform distribution of the liquids

contained in pans or pots.

To check whether the cooker is level,

use a spirit level on the hob

surround. Check the level first front

to back and then side to side.

Non-tip device

When installing the cooker it

is compulsory to install the non-

tip device. The non-tip device

should be fitted, to prevent the

cooker from tipping if subjected to

an abnormal loading, for example

by a child climbing on to an open

oven door. The non-tip device can

only provide protection when the

cooker is pushed into its normal

position.

Before fitting the non-tip device, make

sure the cooker has been leveled.

Draw a line on the wall – after

leveling the cooker – along the top

edge of the hob (see illustration).

The measurements shown can be

applied when the non-tip device is

fitted on the left (see illustration).

Measure and mark where the non-tip

device is to be placed. Attach the

bracket to the wall with the fixings

that are recommended for your wall

type and then check that the bracket

is secure enough to hold the cooker

in place with weight applied to the

open cooker door.

10

Due to the large range of wall types

and different fixings required for each

type, the fixings are not supplied, so

the appropriate fixings should be

obtained from a hardware store.

NOTE! If the space between

kitchen units is wider than the

cooker, you will need to alter the

measurements shown in the

illustration if the cooker is to be

centered.

If you alter the measurements,

remember to align the cooker correctly

when pushing it into place, so that the

non-tip device enters the hole on the

cooker rear.

Instructions for locating and

installation of safety locating

bolt.

When installed, the safety locating

bolt will prevent the cooker from being

moved forward causing the anti tilt

bracket to become disengaged from

the rear of the cooker.

In order to install the safety locating

bolt you will have to drill a hole in the

floor.

With the cooker in position it will

permanently occupy and the anti tilt

bracket fully engaged in the slot in the

back panel of the cooker, remove the

bottom drawer from the cooker,

reach inside and locate the safety

locating bolt located at the half of

distance between the 2 front feet of

the cooker and screw the safety

locating bolt until it gently touches

the floor.

After you have marked the hole

position move the cooker in order to

drill a 5mm diameter hole 20 mm

deep.

Move the cooker back into its

permanent position with anti-tilt

bracket engaged and screw the

safety locating bolt into the hole in

the floor.

Try to pull the cooker forward to

confirm that the screw is sufficiently

engaged in the floor hole.

Confirm that the anti tilt bracket is

sufficiently engaged into the rear of

the cooker by putting some weight

on the open oven door. (not so much

that it causes damage…)

11

Installation

Important

Qualified personnel must install

this cooker. The manufacturer will

not accept liability, should the

above instructions or any of the

other safety instructions

incorporated in this book be

ignored.

Regulations

This appliance shall be installed in

accordance with the manufacturer’s

installation instructions, local gas

fitting regulations, municipal

building codes, AS5601 (AG601)

and any other relevant statutory

regulations.

Rating label

The rating label is located on the

lower front frame of the cooker upon

opening the door. This appliance is

suitable for Natural and Universal

LPG. Ensure that the gas supply

matches the rating label. A duplicate

data label has been supplied with

this appliance, which must be

attached to readily available adjacent

surface on installation.

Ventilation

Ventilation must be in accordance

with AS5601 (AG601) Installation

Code. In general, the appliance

should have adequate ventilation

for complete combustion of gas

and to maintain temperature of

immediate surroundings within safe

limits.

Connection to the gas supply

Gas connection must be carried out

by a licensed gas fitter and in

conformity with the regulations in

force. The appliance leaves the factory

tested and regulated for the type of

gas indicated on the plate, which is

situated in the lower position near

the gas connection tube.

Ascertain that the type of gas with

which the appliance will be supplied

is the same as that indicated on the

plate.

If different carry out all the operations

according to the indications cited in

the paragraph “adaptation of different

types of gas”.

For a maximum output and minimum

consumption ascertain that the

pressure of the gas used the values

indicated in the table of “burners

characteristics”.

The joint is mounted on the intake

area of the pipe, fitted with a filleted

nut G1/2”, between the sealing

components. Screw the parts without

forcing, turn the joint in the direction

required and then tighten everything.

12

Connection

Carry out the connection to the gas

plant only by means of a rigid

metallic pipe conforming to the

regulations in force. This appliance

is NOT suitable for connection with

a flexible hose assembly.

The joint for the entry of the gas

into the appliance is threaded

G1/2”.

Carry out the connection avoiding

any type of stress on the appliance

or gas piping.

Natural gas appliances must be

fitted with a pressure regulator

installed at the inlet connection.

The gas pressure is pre-set and the

gas regulator non-adjustable.

For U-LPG the same pressure

regulator may be used by removing

the centre insert and setting it for

U-LPG setting (remove and re-

insert plastic insert inverted).

Alternatively it can be used without

the regulator and set by

adjustments made via the regulator

fitted at the domestic U-LPG

cylinder.

13

Important

Upon completion of installation,

always check:

- That all the joints are completely

sealed by using a soapy solution,

never a flame;

- That the gas pressure has been

regulated to 1,00 kPa for Natural

Gas and 2,60 kPa for Universal-

LPG. The pressure test point is

located on the regulator for

Natural Gas models or at the top

left hand rear of the cooker for U-

LPG models.

- That the manual ignition system

is operating satisfactory on all

burners, both individually and in

combination;

- That the burners correctly, are

stable, without yellow tipping or

excessive noise on high and low

flame.

Then demonstrate to the customer

the appliance operation and leave

these instructions.

Adaptation to different type of gas

Your cooker is designed to work with

natural gas, and is convertible for use

with propane or butane.

The U-LPG conversion kit is supplied

in the instruction manual packaging.

After completion of any repairs,

adjustments or conversion the

statutory safety tests, must be

carried out.

Stick the label corresponding

to the type of gas used.

14

Burner characteristics

Burner

Normal

power

(MJ/h)

Simmer

power

(MJ/h)

By-

pass

(mm)

Gas Type

Pressure

(kPa)

Nozzle

diameter

(mm)

RAPID

10,5

2,62

0,42

Natural Gas

U-LPG

1,00

2,60

1,39

0,90

SEMI-

RAPID

7,0

6,5

1,75

1,62

0,35

Natural Gas

U-LPG

1,00

2,60

1,11

0,71

AUXILIARY

4,2

4,0

1,05

1,00

0,29

Natural Gas

U-LPG

1,00

2,60

0,89

0,55

Before any modifications or

conversion to a kind of different

gas, you must DISCONNECT the

cooker from the electricity supply

and ensure that all control knobs

are in the OFF position, and the

appliance has cooled completely.

Replace the nozzles of the hob

burners

Hob burners

• Remove the pan supports;

• Remove the caps and the burner

crowns;

• Using a No 7 socket spanner

unscrew the nozzles and replace

them with those required for the

type of gas in use (see burners

characteristics table above).

Reassemble the parts following the

same procedure in reverse.

These burners do not need any

primary air regulation.

15

Adjustment of minimum level for

the hob burners

The burner is correctly adjusted

when the flame is stable silent and

goes out without any noise.

When changing the type of gas

check that the minimum level is

correct. The air admission is correct

when the flame is about 4 mm in

length.

The top burners do not need

adjustment of primary air.

Check that, turning the knob quickly

from the maximum position to the

minimum one, the flame does not go

out.

Hob burners

To adjust the minimum level:

• Light the burner

• Turn the knob to the position of

the minimum flame;

• Remove the knob;

• Unscrew or screw the by-pass

screw until a regular small flame

is reached.

• For U-LPG screw completely the

by-pass screw.

Reassemble the parts following the

same procedure in reverse.

Check that, when turning the knob

quickly from the maximum position to

the minimum one, the flame does not

go out.

no air

correct

adjustment

excess of

air

16

Electrical connections

Any electrical work required

to install this cooker and the

supply cable should be carried out

by a qualified licensed electrician,

in accordance with the current

regulations.

This cooker must be earthed.

The manufacturer disclaims

any responsibility should these

safety instructions not be carried

out.

Before any maintenance or

cleaning can be carried out, you

must DISCONNECT the cooker

from the electricity supply.

This cooker is designed to be

connected to a 230-240V AC, 50Hz

electrical supply.

To connect to the electricity supply,

use cable type H05 RR-F.

Before connection, make sure the

electricity supply voltage is the same

as that indicated on the rating plate.

The cooker is supplied with supply

cable incorporating a 10A plug.

Connect the plug to an appropriate

10A socket. Any electrical work for

example to install a 10A socket must

be completed by a licensed

electrician.

If hard wiring to the mains is

required, an omnipolar interrupter

with a minimum opening of 3 mm

between contacts dimensioned to

the voltage and corresponding to

the regulations in force, should be

interposed between the appliance

and the supply.

The interrupter must not interrupt

the yellow-green earth cable.

After installation and connecting,

the cable must be placed so that it

cannot at any point reach a

temperature of more than 50°C

above the ambient temperature.

supply

cable

NO

After connection try out the heating

elements allowing them to function

for approximately 3 minutes.

If the supply cable is

damaged, the manufacturer or its

service agent or a similarly

qualified person must replace it

in order to avoid a hazard.

17

18

Instructions for the User

Use and care

Control panel

3

2 4 6

9

1

7

8

TEMPERATURE FUNCTION

5

1. Back left burner control knob

2. Front left burner control knob

3. Front right burner control knob

4. Back right burner control knob

5. Ignition switch

6. Oven thermostat

7. Oven thermostat pilot light

8. Function pilot light

9. Oven function control knob (selector)

Hob

1

2

4

3

1. Back left burner (auxiliary)

2. Front left burner (rapid)

3. Front right burner (semi-rapid)

4. Back right burner (semi-rapid)

19

Use of Appliance

Before the First Use of the Oven

Before the first use ensure

that the room is well ventilated:

V.M.C. (Mechanic ventilation) or

opened window.

Remove all packaging, both

inside and outside the oven,

before using the oven.

Before first use, the oven should be

heated without food. During this

time, an unpleasant odour may be

emitted. This is quite normal.

1. Remove the oven accessories.

2. Remove any adhesive labels or

protective films, if there are any.

3. Heat the oven the corresponding

knob on position “250” for about

45 min.

This procedure should be repeated

with the grill function for approximately

5-10 minutes.

Clean the accessories with a soft

detergent. Rinse and dry carefully.

About condensation and steam

When food is heated it produces

steam in the same way as a boiling

kettle. The oven vents allow some of

this steam to escape. However,

always stand back from the oven

when opening the oven door to

allow any build up of steam or heat to

release.

If the steam comes into contact with

a cool surface on the outside of the

oven, e.g. a trim, it will condense and

produce water droplets. This is quite

normal and is not a fault with the oven.

To prevent discolouration, regularly

wipe away condensation and also

spillage from surfaces.

Cookware

Use any ovenproof cookware,

which will withstand temperatures

of 250

°

C.

Oven dishes, etc. should not be

placed directly on the oven base.

During cooking the oven

door becomes hot. Take care

that children do not play near it.

20

Electric Oven

Oven Function Control Knob

Oven switched off

Bake

Conventional cooking –

The heat comes from both

the top and bottom element,

ensuring even heating inside

the oven

Grill The grill cannot be used at

the same time as the oven.

The oven door must be

closed when grilling.

Base

Heat

Bottom heating element –

The heat comes from the

bottom of the oven only.

Fan

Bake

Fan cooking – Heat is

transmitted to food by means

of pre-heated air throughout

a fan located on the back

wall of the oven.

Defrost

This setting is intended to

assist in thawing of frozen

foods.

Thermostat Control Knob

By turning the oven control knob

clockwise, you select the cooking

temperature.

The temperatures shown here are on

the actual control knob.

Temperature selection starts at 50C

and will reach approximately 250C at

the centre of the oven.

The thermostat controlling the

temperature is variable so it is possible

to select temperatures between those

marked.

The maximum setting is particularly

suitable for grilling.

Page is loading ...

No Brand CKG5060S User manual

No Brand CKG5060S User manual

Related papers

Other documents