3com S21x User manual

Category
Networking
Type
User manual

This manual is also suitable for

3Com
®
Corporation
PathBuilder
S21x Switch
Installation Manual
Notice
©
1998 3Com Corporation
5400 Bayfront Plaza
Santa Clara, CA 95052-8145
(408) 326-5000
All rights reserved.
Printed in U.S.A.
Portions reprinted with the permission of Motorola, Inc.
Restricted Rights Notification for U.S. Government Users
The software (including firmware) addressed in this manual is provided to the U.S.
Government under agreement which grants the government the minimum “restricted rights”
in the software, as defined in the Federal Acquisition Regulation (FAR) or the Defense
Federal Acquisition Regulation Supplement (DFARS), whichever is applicable.
If the software is procured for use by the Department of Defense, the following legend
applies:
Restricted Rights Legend
Use, duplication, or disclosure by the Government
is subject to restrictions as set forth in
subparagraph (c)(1)(ii) of the
Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013.
If the software is procured for use by any U.S. Government entity other than the Department
of Defense, the following notice applies:
Notice
Notwithstanding any other lease or license agreement that may pertain to,
or accompany the delivery of, this computer software, the rights of the
Government regarding its use, reproduction, and disclosure are as set forth
in FAR 52.227-19(C).
Unpublished - rights reserved under the copyright laws of the United States.
®
Notice (continued)
Proprietary Material
Information and software in this document are proprietary to 3Com (or its Suppliers) and
without the express prior permission of an officer of 3Com, may not be copied, reproduced,
disclosed to others, published, or used, in whole or in part, for any purpose other than that for
which it is being made available. Use of software described in this document is subject to the
terms and conditions of the 3Com Software License Agreement.
This document is for information purposes only and is subject to change without notice.
Part No. T0032, Rev. C
First Printing October 1998
Manual is current for Release 5.2M.
v
About This Manual
Overview
Introduction
This manual covers features, hardware, installation, applications, and specifications
for the PathBuilder S21x switch.
Audience
This manual is intended for users of the 3Com PathBuilder S21x switch.
Software Revision
This manual is current for Release 5.2M of the Operating Network Software (ONS).
Special Notices
The following notices emphasize certain information in the manual. Each serves a
special purpose and is displayed in the format shown:
Note
Note is used to emphasize any significant information.
Caution
Caution provides you with information that, if not followed, can result in damage to
software, hardware, or data.
Mise en Garde
Une mise en garde vous fournit des informations qui, si elles ne sont pas observées,
peuvent se traduire par des dommages pour le logiciel, le matériel ou les données.
Vorsicht
Ein Vorsichtshinweis macht Sie darauf aufmerksam, daß Nichtbefolgung zu
Software-, Hardware- oder Datenschäden führen kann.
Warning
Warning is the most serious notice, indicating that you can be physically hurt.
Avertissement
Un avertissement constitue le message le plus sérieux, indiquant que vous pouvez
subir des blessures corporelles.
Warnung
Eine Warnung ist der ernsthafteste Hinweis auf Körperverletzungsgefahr.
vi
About This Manual (continued)
Trademarks
The following are trademarks or registered trademarks of their respective companies
or organizations.
Product Company/Organization
Crosstalk Digital Communications Associates, Inc.
HyperTerminal Hilgreave, Inc.
ProComm Datastorm Technologies, Inc.
Windows Microsoft Corporation
PathBuilder 3Com Corporation
vii
About This Manual (continued)
How to Use This Manual
Follow these steps to use this manual to install your PathBuilder S21x switch.
1 Familiarize yourself with the
PathBuilder S21x switch
See Chapter 1, About the PathBuilder
S21x Switch
2 Install the PathBuilder
S21x switch hardware
See Chapter 2, Installing the PathBuilder
S21x Switch Hardware
3 Power up the PathBuilder
S21x switch and access
the control terminal port
See Chapter 3, Powering on the
PathBuilder S21x Switch
viii
About This Manual (continued)
Chapter
Descriptions
This table briefly describes each chapter of this manual.
This section... Describes...
Chapter 1, About the
PathBuilder S21x Switch
the PathBuilder S21x switch.
Chapter 2, Installing the
PathBuilder S21x Switch
Hardware
the shipment contents, hardware installation
and cabling for the PathBuilder S21x switch.
Chapter 3, Powering on
the PathBuilder S21x
Switch
the power up sequence and diagnostics, and
how to access the control terminal port.
Appendix A, Specifications the physical and environmental specifications
and power requirements for the PathBuilder
S21x switch.
Appendix B, PathBuilder S21x
Switch Cabling
identification of all cabling and connections for
the PathBuilder S21x switch.
Appendix C, Troubleshooting
Your PathBuilder S21x Switch
actions you can take to correct problems you
may encounter with your PathBuilder S21x
switch.
Appendix D, Technical Support technical support.
ix
About This Manual (continued)
Related Documentation
Introduction
This section describes related documentation and where to obtain documentation.
Other
Documentation
All documentation is provided on the PathBuilder S200 Series User Guides CD-
ROM and the 3Com WWW site:
http://www.3com.com
PathBuilder S200
Series User Guides
CD-ROM
The PathBuilder S200 Series User Guides CD-ROM contains all PathBuilder S200
series switch documentation available at the time of release. The PathBuilder S200
Series User Guides CD-ROM is shipped with each PathBuilder S200 series switch
product.
WWW
Check the 3Com WWW site for the latest documentation:
http://www.3com.com
Contents
i
How to Use This Manual .............................................................................. vii
Related Documentation ................................................................................ ix
Chapter 1. About the PathBuilder S21x Switch
Features ......................................................................................................... 1-2
Daughtercard Functionality ...................................................................... 1-3
Software Functionality ............................................................................. 1-5
Target Application Environments ................................................................. 1-6
Chapter 2. Installing the PathBuilder S21x Switch Hardware
Checking Your Shipment Contents .............................................................. 2-2
Choosing a Site ............................................................................................. 2-3
Cabling the PathBuilder S21x Switch .......................................................... 2-5
Cables ....................................................................................................... 2-7
Front Panel Dip Switches ............................................................................. 2-10
Installing Optional Daughtercards ................................................................ 2-11
Installing or Removing the Lithium Battery ................................................. 2-12
Chapter 3. Powering on the PathBuilder S21x Switch
Powering On The PathBuilder S21x Switch ................................................ 3-2
Powerup Diagnostics .................................................................................... 3-3
Accessing the Control Terminal Port ............................................................ 3-5
Appendix A.Specifications
Appendix B.PathBuilder S21x Switch Cabling
CTP Access Cable ........................................................................................ B-2
Voice Relay Cable ........................................................................................ B-3
Dual FXS Voice Relay Cable ....................................................................... B-4
10BaseT Crossover Cable ............................................................................ B-5
RemoteVu Video Cables ............................................................................... B-6
DSU Daughtercard Cable ............................................................................. B-7
V.35/V.36 Cable ............................................................................................ B-8
V.11 Cable .................................................................................................... B-10
V.24 Cable .................................................................................................... B-12
Appendix C.Troubleshooting Your PathBuilder S21x Switch
While Setting Up Your Configuration .......................................................... C-2
ii
Contents (continued)
Appendix D.Technical Support
About the PathBuilder S21x Switch 1-1
Chapter 1
About the PathBuilder S21x Switch
Overview
Introduction
The 3Com PathBuilder S21x switch is a compact network access device for
connecting LAN and serial devices to public and private networks services such as
frame relay and X.25. The PathBuilder S21x switch is a desktop-size standalone
device supporting up to two optional daughtercards, as shown in Figure 1-1. Using
the optional daughtercards, the PathBuilder S21x switch offers a flexible and cost
effective solution for transporting data, voice, and video across a network.
Figure 1-1. The PathBuilder S21x Switch
®
1-2 About the PathBuilder S21x Switch
Features
Features
Standard Features
The base PathBuilder S21x switch provides the following:
External power supply
Control Terminal Port (CTP) for local and remote configuration and
management
Ethernet interface (10BaseT)
One Serial DIM Port
Two daughtercard slots
2 MB FLASH and 4 MB DRAM
CTP Port
Port 4 can be used as a Control Terminal Port (CTP) for configuration, reporting, and
troubleshooting the PathBuilder S21x switch. To set Port 4 as CTP, put the front
panel dip switch 4 into the UP position. To access the CTP you must also configure
your terminal or terminal emulation software, to VT100, 9600 bps, 8 bit, no parity, 1
stop bit.
Dual Daughtercard
Slots
The PathBuilder S21x switch comes with two slots to support optional
daughtercards. This permits easy future expansion of the product.
Operating Software
Operating software is compressed in FLASH memory and loaded into DRAM for
operation. The PathBuilder S21x switch supports these Applications Ware packages:
IP Applications Ware Package
IP & IPX Applications Ware Package
SNA Applications Ware Package
Serial Protocol Applications Ware Package
Multiservice Applications Ware Package
Multimedia Applications Ware Package
See the
Software Release Notes
accompanying your PathBuilder S200 series switch
unit for more information on the software available for the PathBuilder S21x switch.
About the PathBuilder S21x Switch 1-3
Features
Daughtercard Functionality
Introduction
The PathBuilder S21x switch is available with the optional components listed below
factory-installed or as separate add-in daughtercards.
Voice Relay Daughtercard
Dual FXS Voice Relay Daughtercard
RemoteVu Daughtercard
DSU Daughtercard
DIM Daughtercard
DRAM SIMMs
Refer to the
PathBuilder S200 Series Switch Daughtercard Installation Manual
(T0020) for information on the installation of optional daughtercards.
Voice Relay
Daughtercard
The PathBuilder S21x switch supports the Voice Relay Daughtercard. This
daughtercard supports one voice channel, using either an analog FXS or FXO
interface. Both interfaces use RJ11 connectors.
Dual FXS Voice
Relay
Daughtercard
The Dual FXS Voice Relay Daughtercard provides two FXS interface ports and
support one voice channel each. The FXS port uses RJ45 connectors.
RemoteVu
Daughtercard
The PathBuilder S21x switch supports video over Frame Relay using the RemoteVu
daughtercard. The RemoteVu Daughtercard provides two BNC connector, video
ports accepting NTSC, PAL or SECAM video signal standards and an RJ-45, RS232/
485 camera control port used for Pan/Tilt/Zoom (PTZ) camera control.
DSU Daughtercard
The DSU daughtercard functionality suits an extended range of 56 kbps
point-to- point DDS1 interfaces that conforms to AT&T 62310 or
ANSI T1E1.4/91-006.
The DSU is FCC Part 68 registered.
Diagnostic loopbacks from the telephone company are supported; local diagnostics
are activated from the CTP.
1-4 About the PathBuilder S21x Switch
Features
DIM Site
Daughtercard
The DIM Site daughtercard provides optional V.24, V.35, V.36, or V.11 electrical
interfaces through a DB25 physical connector.
DSU DIM
The PathBuilder S21x switch supports the DSU DIM.
About the PathBuilder S21x Switch 1-5
Features
Software Functionality
Introduction
Depending on the operating software AppsWare package and optional daughtercard
installed the PathBuilder S21x switch can support the following functionality and
services.
Frame Relay & X.25
Service
The PathBuilder S21x switch provides serial devices with economical Ethernet LAN
access into public or private Frame Relay WAN. Where frame relay services are not
yet available, the PathBuilder S21x switch can provide network access over X.25
services. When frame relay services becomes available, the PathBuilder S21x switch
can be easily configured and integrated to support frame relay. This fast migration
reduced network downtime and protects hardware investments.
RFC 877 and 1356
The PathBuilder S21x switch supports encapsulation of IP datagrams and other
network layer protocols over X.25 as specified in RFC 877 and RFC 1356. This
allows for interoperability with Front End Processors (FEPs) that support X.25 and
IP traffic as well as router vendors supporting RFC 877/1356.
RFC 1490
The PathBuilder S21x switch supports encapsulation of multiple protocols over
frame relay as specified by RFC 1490.
Multiprotocol
Support
Support includes SDLC, Bisync, X.25, Async, IP/IPX, PPP, MLPPP, and Routing
and Bridging, as well as many other serial protocols. Refer to the Software Release
Notice which accompanied your unit for a complete listing of protocols supported by
the PathBuilder S21x switch.
1-6 About the PathBuilder S21x Switch
Target Application Environments
Target Application Environments
Introduction
This section describes example applications for the PathBuilder S21x switch.
LAN and Legacy
Protocol over
Frame Relay
The PathBuilder S21x switch supports multiprotocol encapsulation of IP traffic and
legacy serial protocols over frame relay as specified by RFC 1490. As shown in
Figure 1-2, a SNA cluster controller connects to a serial port on the PathBuilder S21x
switch and the Ethernet LAN connects to the 10BaseT Ethernet port. The PathBuilder
S200 series switch is fully interoperable with third party routers via RFC 1490.
Figure 1-2. LAN and Legacy Protocol over Frame Relay
Video and Legacy
Protocols over
Frame Relay -
Banking
Application
As shown in Figure 1-3, the PathBuilder S21x switch can support encapsulation of
video and legacy protocol over frame relay. This use of PathBuilder S21x switch
suits banking applications such as Automated Bank Machines (ABMs). With Dial on
Demand software feature enabled, the PathBuilder S21x switch initiates a connection
only when there is data transfer, i.e. only for the duration of a bank transaction. The
RemoteVu Daughtercard can capture video and send video streams to the central
bank’s security system.
Figure 1-3. LAN and Legacy Protocol over Frame Relay
Third Party
Router
PB S200
Frame Relay
Ethernet
Cluster
Controller
Terminals
Ethernet
Third Party
Router
FEP
HOST
Frame Relay
Equipped with
RemoteVu
Daughtercard
PCs Running Host Video
Workstation Application
Central BankAutomated Teller Machine
S200
FEP
HOST
Video
Camera
Bank ATM
About the PathBuilder S21x Switch 1-7
Target Application Environments
Branch Office to
Central Office over
Frame Relay
The PathBuilder S21x switch offers an ideal solution for branch office to central
office connectivity over a private or public frame relay network as shown in
Figure 1-4.
Figure 1-4. PathBuilder S21x switch supporting Voice and Video over
Frame Relay
Frame Relay
Equipped with DSU DIM,
Voice Relay, and ISDN
Daughtercards
Branch Office
Security Monitoring
at Branch Office
Video Camera
Ethernet
PCs Running Host Video
Workstation Application
Central Office
ISDN
Equipped with
RemoteVu Daughtercard
PB S200
Ethernet
PBX
PB S200
PBX
Application
Type
Daughtercard
Used
Application Description
Branch access to
Central Office
DSU DIM and Voice
Relay Daughtercards
The PathBuilder S21x switch supports voice, video and
data traffic between the branch and central office over pri-
vate or public frame relay network. The Voice Relay
Daughtercard supports telephones, PBX, and faxes.
Connect a telephone or PABX to one FXS port on the
Voice Relay Daughtercard and all branch telephones have
access to the central office PBX. This eliminates long
distance telephone charges between the branch and
central office.
Security
Monitoring at
Branch Office
RemoteVu and DSU
Daughtercards
The PathBuilder S21x switch equipped with a RemoteVu
Daughtercard provides security surveillance and remote
monitoring of the branch office location from the central
office. The RemoteVu Daughtercard packetizes video
stream in IP and sends the data over the frame relay.
Security personnel at the central office can control the
branch office video camera from a PC running the Host
Video Workstation application.
1-8 About the PathBuilder S21x Switch
Target Application Environments
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

3com S21x User manual

Category
Networking
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI