HDSDI input kit
Installation manual
iCon H250/H50 0 — iD H 250/H500
R9843047
R59770251/01
30/10/2008
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w ar-
ranties or m erchantability and fitness for a particular purpose. Barco m ay m ake improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This pub lication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, re produced or translated. It shall not other
wise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Guaran tee and Compensation
Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. O n receipt, the pu rchaser
must immediately inspect all delivered goods for dam age incurred during transport, as well as for material and manufacturing faults Barc o
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of c omm issioning,
at latest 30 days after the transfer of risks. In the ev ent of justified notice of complaint, Barco can r epair the fault or provide a replac ement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or c ancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or p art of Barco.
If the pur chaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are ha ndled incorrectly,
in particular if t he systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be r endered invalid. N ot inc luded in the guarantee cove rage a re
system failures which are attributed to programs or special electronic c ircuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and m
aintenance regulations s pecified in the this manual m ust be com plied with by
the customer.
Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................. 3
1.1 Safety warnings....................................................................................................................... 3
2. Kit description ...................................................................................................... 5
2.1 Kit information ........................................................................................................................ 5
2.2 Kit content ............................................................................................................................ 6
3. Removing the DVI/D15 input layer .............................................................................. 9
3.1 Removing the cable basket .......................................................................................................... 9
3.2 Removing the lens.................................................................................................................... 9
3.3 Removing the rear cover ............................................................................................................ 10
3.4 Removing the top cover............................................................................................................. 11
3.5 Removing the PMP..................................................................................................................13
3.6 Removing the input module .........................................................................................................15
3.7 Removing the backplane............................................................................................................16
3.8 Removing the front plate ............................................................................................................ 16
3.9 Removing the DVI/D 15 input board.................................................................................................17
4. Installation of the SDI/HDSDI input board ................ .. ................. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ... 19
4.1 Installing the SDI/HDSDI input board ...............................................................................................19
4.2 Installing the front plate and front plate shield......................................................................................19
4.3 Installing the backplane ............................................................................................................. 20
4.4 Assembling the projector............................................................................................................ 21
Index......................................................................................................................23
R59770251 HDSDI INPUT KIT 30/10/2008 1
Table of contents
2 R59770251 HDSDI INPUT KIT 30/10/2008
1. Safety
1. SAFETY
1.1 Safety warnings
WARNING: This procedure is intended for Barco authorized technicians only.
WARNING: Risk of electrical shock. Make sure that the projector is p owered do wn an d that the power cord
is re moved fro m the wal l ou tl e t.
WARNING: Risk o f burns. Wait until the projector has cooled down for at least 15 minutes before starting this
procedure.
CAUTION: Wear a wrist band which is connected to the ground while handling the electrostatic discharge
sensitive parts.
R59770251 HDSDI INPUT KIT 30/10/2008 3
1. Safety
4 R59770251 HDSDI INPUT KIT 30/10/2008
2. Kit description
2. KIT DESCRIPTION
Overview
• Kit information
• Kit c onte nt
2.1 Kit information
Introduction
This k it contains a SDI/HDSD I input boa rd which can be installed on the following projectors:
• iCon H250
• iCon H500
• iD H250
• iD H500
It replaces the DVI/D15 input board which by default is installed as layer three in the input module of these projectors.
Image 2-1
iCon H250/H500: DVI input layer
Image 2-2
iD H250/H500: DVI input layer
The SDI/HDSDI input board ha s four BNC connectors:
• both BNC connectors at the left side are input connectors
• both BNC connectors at the right side are the output connectors
Both input conne ctors can have a source connected, b ut only one out o f these two can be switched to the PMP at the same time.
This selected input is then looped through to both output connectors.
Image 2-3
SDI/HDSDI input board: picture
CABLE
EQUALISER
CABLE
DRIVER
IN 1
OUT 1
OUT 2
IN 2
CABLE
EQUALISER
serial
parallel
CTRL
I²C
10 bits
20 bits
Eid
I²C stby
SPI
1
80
.
.
.
HDSDI input *
DESERIALIZER
Image 2-4
SDI/HDSDI input board: block diagram
The serial digital video signal is deserialized and converted into a 10 bits or 20 bits parallel signal.
R59770251 HDSDI INPUT KIT 30/10/2008
5
2. Kit description
This kit can not be used in combination with the D VI HDCP upgrade kit R9843045
2.2 Kit content
Kit overview
The kit contains the S DI/HDSDI input board, the new fr ont plate and the front plate shield for the projector. Two different front
plates are included, but o nly the one that fits your projector is ne eded.
The s hield will be m ounted between the front plate and the input boards for EMC reasons.
Article n um ber Description
Quantity
Image
R764442 SDI/HDSDI input bo ard 1 pc See image 2-5
R857755 Front plate iD H250/H500 1 pc See image 2-6
R854770 Front plate iCon H250/H500 1 pc See image 2-7
R857758 Front plate shield 1 pc See image 2-8
V3636027 Fixing screw 4 pcs See image 2-9
Image 2-5
SDI/HDSDI input board
Image 2-6
Front plat e iD H250/H 500
R / PR G / Y B / PB Hs / Cs Vs VIDEO S-VIDEO
MIC IN LINE IN
USB
10/100Base-T
PC CARD
OUT
IN 1 OUTIN 2 OUT
HDSDI/
SDI
Image 2-7
Front plate iCon H250/H500
Image 2-8
Front plate shield
6 R59770251 HDSDI INPUT KIT 30/10/2008
2. Kit description
Image 2-9
Fixing screw
R59770251 HDSDI INPUT KIT 30/10/2008 7
2. Kit description
8 R59770251 HDSDI INPUT KIT 30/10/2008
3. Removing the DVI/D15 input layer
3. REMOVING TH E DVI/D15 INPUT LAYER
Overview
• Removing the cable basket
• Removing the lens
• Removing the rear cover
• Removing the top cover
• Removing the PMP
• Removing the input module
• Removing the bac kplane
• Removing the front plate
• Removing the DVI/D15 input board
The pro cedure for the iD H250/H500 is the almost same as the pro cedure for the iCo n H250/H500.
In the different step of this procedure the difference between the iD H 2 50/H500 an d the iCon H250/H500 will
be m entioned in a clear way!
3.1 Removing th e cable b asket
Necessary tools
No tools.
How to remove the cable basket?
1. Slightly push downwards the middle top of the cable basket to unlock the upper part.
2. Pull the cable basket o ut of it bottom lock.
Image 3-1
3.2 Removing the lens
Necessary tools
No tools.
How t o remove the lens?
1. Support the lens with on e hand.
2. Unlock the lens by pulling the handle which is located on the right side of the projector.
3. Pull the lens out of the lens holder.
R59770251 HDSDI INPUT KIT 30/10/2008 9
3. Removing the DVI/D15 input layer
Image 3-2
removal of the lens
CAUTION: Never transport the projector with the lens mounted on it! Alw ays remove the lens before trans-
porting the projector.
3.3 Removin g the rear cover
Necessary tools
Slotted screwdriver 10 mm
WARNING: Risk of burns: respect the cooling down time of the projector before starting any replacement
procedures!
WARNING: Risk of electrical sh ock: before
starting the replacement procedures, power down the projector
and unplug the power cord from the wall outlet!
How to remove the back cover?
1. Use a screwdriver to turn the rear cover lock sc rew a quarter turn counterclockwise.
10
R59770251 HDSDI INPUT KIT 30/10/2008
3. Removing the DVI/D15 input layer
Image 3-3
Rear cover fixing screw
2. Tilt the rear cover and remove it.
Image 3-4
Tilt rear cover to remove it
3.4 Removing the top cover
Necessary tools
Phillips screwd river Ph2
How to remove the top cover?
1. Loosen and remove the screws A (3pc) and B ( 2pc) retaining the top cover
R59770251 HDSDI INPUT KIT 30/10/2008
11
3. Removing the DVI/D15 input layer
Image 3-5
remove the 3 screws o n the left
Image 3-6
remove the 2 screws on the right
2. Unplug the con nector on the keypad / IR receiver
12 R59770251 HDSDI INPUT KIT 30/10/2008
3. Removing the DVI/D15 input layer
Image 3-7
Unplug the touchpad/IR connector
3. Remove the top cover
Note: Unplugging the IR receiver will not interrupt the IR com munica tion with the RCU since an add
itional IR receiver is mounted
on the PMP board.
3.5 Removing the PMP
To install this input upgrade kit, it is not n ecessary to comple
tely remove the PMP. The input m odule can be
made accessible by disconnect ing the P MP partially and just flipping it over.
Necessary tools
• Torx screwdriver T10
• Nut sp anner 5 mm
How t o flip over the PMP?
1. Remove the front screw, fixing the upper part of the front panel to the input module
Image 3-8
iCon and iD H250/H500: fixing screw of the front plate upper part
2. Remove the 6 bolts, fixing the upper part of the front panel to the PMP
R59770251 HDSDI INPUT KIT 30/10/2008
13
3. Removing the DVI/D15 input layer
Image 3-9
iCon and iD H250/H500: fixing bolts of the front plate upper part
3. Remove the upper part of the front panel
4. Unplug connector J110 (cable coming from the SBC) — ONLY FOR ICON H250/H500
Image 3-10
iCon H250/H500 ONLY: unplug connector J110 on the PMP
5. Remove both fixing screws
Image 3-11
iCon H250/H500: PMP fixing screws
Image 3-12
iD H250/H500: PMP fixing screws
6. Disconnect the PMP from the backplane, by lifting it
7. Flip over the PMP, in order to get access to the input modu le
14
R59770251 HDSDI INPUT KIT 30/10/2008
3. Removing the DVI/D15 input layer
Image 3-13
PMP flipped over
3.6 Removing the input module
Necessary tools
Phillips screwdriver Ph1 — long model
How to remove the input module?
1. Remove the pixel map processor (PM P) — Se e the concerning chapter.
2. Loosen the two screws fixing the input m odule (use a long screwdriver).
Image 3-14
Fixing screws of the input box
3. Slightly lift the input module and disconnect the power connector
- J419 (6 wires): power from the power box (co
nnector 6)
Image 3-15
4. Lift the input m odule to remov e it
R59770251 HDSDI INPUT KIT 30/10/2008
15
3. Removing the DVI/D15 input layer
3.7 Removing the backplane
Necessary tools
No tools.
How t o remove the backplane?
1. Remove the backplane by gently disconnecting it from the input module
Image 3-16
Disconnecting the backplane of the iCon H250/H500
Image 3-17
Backplane of the iCon H250/H500 disconnected
Image 3-18
Disconnecting the backplane of the i D H250/H500
Image 3-19
Backplane of the iD H250/H500 disconnected
3.8 Removing the front plate
Necessary tools
• Torx screwdriver T8
• Torx screwdriver T10
• Nut sp anner 5 mm
How to remove the front plate
1. Remove the screws fixing the front plate
16
R59770251 HDSDI INPUT KIT 30/10/2008
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
Barco iCon H400 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco iCon H250 Installation guide
-
Barco SDI input kit for iD series Installation guide
-
Barco DVI/D15 input board for iCon Installation guide
-
Barco Audio switching and video input kit for iD series Installation guide
-
Barco iD H500 User manual
-
Barco Galaxy NW-7 EX Installation guide
-
Barco Twin dual DVI-D link Installation guide
-
-
-
Other documents
-
Extron PMP Series User manual
-
Ruckus Wireless ZoneFlex H500 Quick Setup Manual
-
Ruckus Wireless ZoneFlex H500 Quick Setup Manual
-
Tektronix H500 User manual
-
Hitachi CP-WU13K User manual
-
-
Vislink IRD6200 User manual
-
KROHNE H250 M40 FOUNDATION FIELDBUS Owner's manual
-
-
Classic ECO2 H500 User manual
