Anova L1369A Installation guide

Anova
Brand
Anova
Model
L1369A
Type
Installation guide

This manual is also suitable for

anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
(4) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Optional: (4) 3/8"
Rubber Washers
90130A050Hammer Drill
Masonry Drill Bit Set
3/16", and 3/8"
Hammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
Streetside Benches
Care should be given to avoid rubbing the powder
coating o the foot. A 3/8" rubber washer is a suitable
replacement option. Mount the bench to the ground
by placing a washer and a nut onto each anchor.
Leave the hardware nger tight until all of them have
been installed. Verify that the bench is level before
tightening the anchors. Tighten all of the hardware
with a 9/16" wrench.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
Place bench in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference
page 3.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
2
5
4
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving
it several hammer blows.
6.
7.
Repeat steps 2 - 5 until all anchors are installed.
Remove the nuts and washers o of the anchors. Align the
mounting holes of the bench over top of the anchors and slide it
down into place.
8.
!
Streetside Benches
Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Streetside Benches
11/13/2018
FOOT MOUNTS:
SECTION B-B
SCALE .09375
B B
1
1
2
2
3
3
4
4
A A
B B
1
A02
4FT RENDEZVOUS BN W/SQ END
OF
L1368
1
REV
SHEET
.09375:1
SCALE
DATE
1/16/2007
DWG NO
TITLE
B
DRAWN
steve
SIZE
THIS DRAWING AND ALL ITS INCLUDED
INFORMATION IS THE PROPERTY OF
LANDSCAPE BRANDS. DO NOT USE OR
COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS
SUBJECT TO RETURN ON DEMAND.
ALL DIMENSIONS ARE IN INCHES
AND ALL ANGLES OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
PRINT IS FOR FABRICATION
ONLY. SURFACES MAY PICK
UP .093
.0625 OF COATING.
TOLERANCES UNLESS NOTED:
X.XX ± .25 X.XXX ± .125 X.XXXX ± .0625
X.XXXXX ± .03125 ANGULAR ± 1
DO NOT SCALE DRAWING
211 N. Lindbergh Blvd.
St. Louis, MO
63141-7809
888-535-5005
www.landscapebrands.com
REV DESCRIPTION ECN TR# DATE
1RELEASE TO PRODUCTION NONE ????
A01
UPDATED TITLE BLOCK, ADDED
REVISION BLOCK, CHANGED LEGS TO
SU80 AND SU81, REDIMENSIONED PART NONE 09/15/10
A02 ADDED FOOT MOUNT VIEW NONE 11/13/18
51.50"
19.15"
26.56"
1.50"
48.25"
23.58"
33.44"
25.60"
49.75"
16.83"
0.50"
(4 PLCS)
49.75"
16.83"
Ø.50"
(4 PLCS)
L1368
Surface Mounting
A A
1
1
2
2
3
3
4
4
A A
B B
1
A01
4FT RENDEZVOUS BN W/SQ END
OF
L1369
1
REV
SHEET
.09375:1
SCALE
DATE 1/24/2007
DWG NO
TITLE
B
DRAWN steve
SIZE
THIS DRAWING AND ALL ITS INCLUDED
INFORMATION IS THE PROPERTY OF
LANDSCAPE BRANDS. DO NOT USE OR
COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS
SUBJECT TO RETURN ON DEMAND.
ALL DIMENSIONS ARE IN INCHES
AND ALL ANGLES OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
PRINT IS FOR FABRICATION
ONLY. SURFACES MAY PICK
UP .093
.0625 OF COATING.
TOLERANCES UNLESS NOTED:
X.XX ± .25 X.XXX ± .125 X.XXXX ± .0625
X.XXXXX ± .03125 ANGULAR ± 1
DO NOT SCALE DRAWING
211 N. Lindbergh Blvd.
St. Louis, MO
63141-7809
888-535-5005
www.landscapebrands.com
REV DESCRIPTION ECN TR# DATE
A01 UPDATED TITLE BLOCK, ADDED REVISION BLOCK, CHANGED
LEGS TO SU80 AND SU81, REDIMENSIONED PART NONE 09/15/10
A02 surface mount view added none 07/11/18
19.15"
26.56"
23.58"
75.38"
1.50"
72.25"
33.44"
25.60"
72.25"
1.50"
75.38"
73.63"
16.83"
0.50"
(4 PLCS)
Ø.50"
(4 PLCS)
73.63"
16.83"
L1369
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova L1369A Installation guide

Anova
Brand
Anova
Model
L1369A
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents