B-Tech BT8565 Installation guide

B-Tech
Brand
B-Tech
Model
BT8565
Category
Wall & ceiling mounts accessories
Type
Installation guide
BT8565
UNIVERSAL EXTRA-LARGE
flat screen Display Trolley
WITH ADJUSTABLE HEIGHT
INSTALLATION GUIDE
www.btechavmounts.com
B-TECH AV mounts
vesa
1000
x
600
• Recommended for screens up to 120"
• Suitable for loads: 50kg - 83kg (110lbs - 183lbs)
• Suitable for displays with VESA® & non-VESA
xings up to 1000 x 600mm
• Tool-less height adjustment of screen
• Non-marking locking / braked castors included
• Integrated cable management
• Dimensions: H.1905mm W.1697mm D.991mm
SPECIFICATIONS
83kg
2
CONTENTS
Installation Safety Notes......................................................................................................................
Parts List....................................................................................................................................................
Installation Instructions.......................................................................................................................
Product Dimensions............................................................................................................................
B-Tech Contact Details........................................................................................................................
2
4
6
18
20
INSTALLATION SAFETY INSTRUCTIONS
CAUTION:
Do not attempt to install this product until all instructions and warnings have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.
B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper
installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably qualied person install this product.
Warning: The trolley can tip over which may lead to serious injury. Only adults should push this trolley, do not allow
children under 16 to move the trolley. Push the trolley on the narrow side, never pull the trolley. Do not push at the top
of the trolley, push near the middle. Move the trolley slowly. Always park on level ground, never leave the trolley on an
incline. Apply the brakes when the trolley is stationary, release the brakes when pushing the trolley.
Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious
injury or death both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds the specic weight limit of the product you are installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Fixing hardware
It is highly recommended that all xing screws be used where supplied and that the purpose of all other xing hardware
is fully understood. In some cases more AV equipment xing hardware will be supplied to accommodate dierent models
of equipment and set up congurations.
The installer must be satised that any supplied xing hardware is suitable for each specic installation.
If any xing screws or included hardware are deemed not sucient for a safe installation then please consult a professional
or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure
that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or trapping of ngers or other
body parts.
Particular attention to the nature of moving parts is required especially when assembling installing and adjusting
during set up.
Immediately after installation double-check that the work done is safe and secure. Double-check all
necessary xings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its xing points are made as frequently as possible to
ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualied person.
This mount is intended for use only with the
maximum weights indicated. Use with screens heavier than the maximum
indicated may result in instability causing possible injury.
Please pay careful attention to where this product is located, some locations are not suitable for installation.
For indoor use only. Install stand on level ground. When verifying the stability of the structure, consider the following
external factors: The strength of the oor, exposure to sudden and severe wind and danger arising from contact with people
and / or objects (eg installations in passageways, emergency exits), if located in a public or frequently populated area ensure
that the product is out of the immediate reach of people.
Trolley Operation
BT8565 PARTS LIST
PLEASE KEEP THIS FOR FUTURE REFERENCE
16
14
13
11
4
5
15
12
4
2
3
1
9
8
7
10
6
5
INSTALLATION TOOLS REQUIRED Crosshead
screwdriver
Pliers w/Cutter
(optional)
27
26
N
Drill with
10mm socket
Level
(optional)
REF PART NAME QTY
1
LEFT BASE
1
2
RIGHT BASE
1
3
BASE CONNECTOR PLATE
2
4
CASTOR
4
5
COLUMN
2
6
MOUNTING BAR
2
7
BALANCE BOX
1
8
BALANCE BOX COVER
1
9
ADAPTOR PLATES
2
10
MOUNTING PLATE
1
11
FRONT COVER
2
12
INTERFACE ARM
2
13
TRIM
2
14
COLUMN REAR COVER
4
15
COLUMN END CAP
2
16
COLUMN STRIP
4
17
5AF HEX KEY
1
18
6AF HEX KEY
1
19
M8 x 16mm CSK SCREW
4
20
M8 x 35mm CSK SCREW
8
21
M10 x 25mm CSK SCREW
8
22
M8 x 10mm SCREW
8
23
M8 x 20mm SCREW
2
24
M8 x 8mm SCREW
12
25
WASHER
4
26
M6 x 20mm CAPHEAD SCREW
2
27
SLIDING NUT
8
INTERFACE KIT
A
M6 x 16mm SCREW
4
B
M6 x 25mm SCREW
4
C
M6 x 40mm SCREW
4
D
M8 x 16mm SCREW
4
E
M8 x 25mm SCREW
4
F
M8 x 40mm SCREW
4
G
M10 x 16mm SCREW
4
H
M10 x 25mm SCREW
4
I
M10 x 40mm SCREW
4
J
M8 x 5mm SPACER
4
K
M8 x 13mm SPACER
4
L
M8 x 24mm SPACER
4
M
M10 x 7mm SPACER
4
N
MULTIWASHER
4
22
24
20
AB
C
D
E
F
G
H
I
J
K
L
M
18
17 19
21
23 25
6
FIX CASTORS TO BASE
Screw 4 x item 4 into items 1 & 2 and apply the brakes.
1.
2.
INSTALLATION INSTRUCTIONS
3
2
1
17
17
27
Connect item 1 and item 2 together.
Fix in place with item 3 by screwing 4 x item 17 into item 1 and 4 x item 17 into item 2
4
1
2
ASSEMBLE BASE
1
2
17
3
1
2
3
7
3.
Stand the base in its upright position.
Insert item 5 into item 1 and screw 4 x item 18 through the underside of item 1.
Insert item 5 into item 2 and screw 4 x item 18 through the underside of item 2.
55
12
27 18
5
27
18
ATTACH COLUMNS TO BASE
18
1
8
4.
ATTACH MOUNTING BARS TO COLUMNS
Slide 4 x item 20 into the front outside slots of both item 5.
Screw 4 x item 21 through holes in each of item 6 into item 20.
Mount 1 x item 6 approx 10mm from the top of item 5 and the other item 6, 435mm down.
10mm
435mm
20
20
6
21
21
20
20
6
6
5
5
26
20
21
9
7
22
26
7
22
6
6
Fix items 7 onto items 6 using 8 x item 22.
5.
FIX ON FRONT COVERS
Insert 2 x item 23 into the top mounting bar (item 6) as shown.
Do not fully tighten, leave a 10mm gap (approx).
INSERT BALANCE BOX MOUNTING SCREWS
6.
6
23
26
mm01
)xorppa(
23
26
6
10
Insert item 8 into the slots on the left and right side of item 9.
7.
INSERT BALANCE BOX REAR COVER
8
8
SLOT
SLOT
Rear of item 9
8
9
9
9
TOP VIEW
23 9
KEYHOLE
6
9
8
8.
HOOK ON BALANCE BOX
Hook on item 9 onto both of item 23 using the key holes on the rear of item 9.
23
11
Using a crosshead screwdriver and a spirit level, adjust the levelling screws on
the front of item 9 until the balance box is level.
9.
LEVEL BALANCE BOX
LEVEL
(not included)
9
LEVELLING SCREW
Fix item 9 to the bottom item 6 using item 24.
9
Insert item 24 through these holes
.
10.
FIX BALANCE BOX
24
26
24
24
12
11.
FIX ADAPTOR PLATES
Fix 2 x item 10 onto item 9 using 4 x item 22.
22
10
9
26
22
Fix item 11 onto item 10 using items 22 & 25.
Use holes as shown below.
There are 3 height options for mounting item 11.
11
22
10
10
FIX MOUNTING PLATE
12.
Option 1
Option 2
Option 3
25
26
13
Bottom
Top
SCREEN
SCREEN
FIX INTERFACE ARMS TO SCREEN
Fix items 12 to the back of the screen using the interface kit (items A-N).
Note: Ensure items 12 are positioned the correct way round.
13.
A-I
N
12
J-M
Spacers (items J-M)
are to be used for
screens with
recessed xings.
PULL STRING
Use magnet
to hide pull string
behind screen
HOOK SCREEN ONTO TROLLEY
Hook screen onto item 11.
Pull down the pull string on items 12 to
secure screen onto item 11, as shown below.
14.
5
12
11
12
SCREEN
14
Note: If necessary, laterally adjust
screen by hand.
HEIGHT
ADJUSTMENT
SCREW
15.
SCREEN ADJUSTMENT
Level screen with the height adjustment screws
at the top of item 12.
Secure screen onto item 11 using the locking screws
at the bottom of item 12.
LOCKING
SCREW
16.
LOCK SCREEN TO MOUNTING PLATE (OPTIONAL)
LEVEL
26
12
SCREEN
SCREEN
26
12
15
To balance the screen, use a drill driver at low torque setting and a 10mm socket.
i. Turn the left spring tension point counter-clockwise for 5 seconds.
ii. Turn the right spring tension point counter-clockwise for 5 seconds.
iii. Repeat steps (i) and (ii) until the screen is nearly balanced.
iv. Fine tune the spring tension points until item 9 can hold the screens
weight at every height (this may take some time).
SPRING TENSION
POINT
SPRING TENSION
POINT
DRILL DRIVER
10mm
SOCKET
17.
BALANCE SCREEN TO ENABLE HEIGHT ADJUSTMENT
Move up and
down with hands
18.
ADJUSTING THE HEIGHT OF THE SCREEN
Now the screen is balanced, use both hands
to gently move the screen up and down.
SCREEN
16
Use pliers to cut
item 16 to correct size
20.
INSERT COLUMN STRIPS
Insert item 16 into the front slots on item 5.
Note: Item 16 will need to be cut to size.
16
iii. Fit item 13 into the front and
rear of item 3.
SCREEN
15
5
3
13
19.
ATTACH PLASTIC COVERS
i. Attach item 14 to the rear of item 5.
ii. Fit item 15 to the top of of item 5.
5
16
16
5
15
14
14
13
3
5
17
21.
Cut-outs in the base can be
used for cable management
CABLE
Cut-outs for
cable management
CABLE MANAGEMENT
Allow enough slack on cables
for the movement of the screen
Cables can be routed
through the cut-outs
in item 14.
Route cables through bottom of items 1 & 2.
Cut-outs in item 1 & 2 can be used for cable management.
Important:
Allow enough slack in the cable to accommodate the height adjustment of the screen.
PRODUCT DIMENSIONS
PLEASE KEEP THIS FOR FUTURE REFERENCE
BT8565
18
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
FRONT VIEW
Max 1000mm
Max 600mm
500mm
400mm
300mm
200mm
100mm
8.5mm
12.5mm
19mm
1932.9mm
122mm
265.1mm
mm3.711
mm01+(
thgieH
)tnemtsujdA
210.5mm
49mm
mm7.2061
190mm
Minimum Height
190mm
HEIGHT OPTIONS
Maximum Height
PRODUCT DIMENSIONS
PLEASE KEEP THIS FOR FUTURE REFERENCE
BT8565
19
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
TOP VIEW
SIDE VIEW
1366.4mm
991.3mm
236.3mm
1697.1mm
473.5mm
35mm
136.5mm
246.4mm
1700mm
609.9mm 270.1mm
111mm
654mm
627.7mm
1523.7mm
158mm
1070mm
435mm
1300.7mm
822.5mm 822.5mm
80mm
30mm
27.2mm
BACK VIEW
820mm
For More Information Visit www.btechavmounts.com
B-TECH AV mounts
AMA-BT8565-V1-0819-110 MADE IN VIETNAM
©2019 B-Tech International Design & Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design & Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
CONTACT:
[email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

B-Tech BT8565 Installation guide

B-Tech
Brand
B-Tech
Model
BT8565
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents