Anviz L100D II User manual

Type
User manual

Anviz L100D II is a Home & Business Smart Lock that can be operated by fingerprint, card, or mechanical key. It can store up to 95 normal users and 4 administrators, making it suitable for small businesses or families. The lock has a low battery voltage alarm and can be powered by four alkaline AA batteries. It also features a normal open function, which allows the door to be opened without fingerprint or card verification, making it ideal for meeting rooms or other places where free access is required. Additionally, the lock can be initialized to factory mode to delete all users.

Anviz L100D II is a Home & Business Smart Lock that can be operated by fingerprint, card, or mechanical key. It can store up to 95 normal users and 4 administrators, making it suitable for small businesses or families. The lock has a low battery voltage alarm and can be powered by four alkaline AA batteries. It also features a normal open function, which allows the door to be opened without fingerprint or card verification, making it ideal for meeting rooms or other places where free access is required. Additionally, the lock can be initialized to factory mode to delete all users.

Before Operation
Note:
Place finger:
1. The lock is equipped with three mechanical keys for manual lock operation. Remove mechanical keys from
the package and keep them in a safe place.
2. To power the lock, four alkaline AA batteries (not included) are required. The lock has low battery voltage
alarm (Red LED flashes and six beeps when you active the lock) to prompt replace battery. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
3. By Default, the lock is configured to grant ANY fingerprint access to unlock.
4. By Default, the lock is configured can not read ID card. Please refer to RFID Card Function to enable card
reading function.
5. Please avoid strong light direct to the lock.
This will normally be an official in the company or the host of a
family who will have administrator permissions and will be able to
do various operations.
The lock can set 4 administrators and ID will be 96--99.
This will be a user under administrator's management who will
be granted access to open the lock. The lock can set 95 normal
users and ID number will be 01--95.
User Operation
Quick Operation Mode
Normal user
The Nixie tube prompting characters
The LED status
--
Bule LED flashes
Red LED light
Red LED flashes
Red LED fast flashing
Bule LED fast flashing
Bule and Red LED flashes
Long Voice
Six beeps
Three Beeps
Two Beeps
Short music voice
Need administrator identification.
Delete user who is identified by fingerprint or card.
Delete all the users.
ID range for normal users. (95 users capacity)
ID range for administrators.(4 administrators capacity)
Ad
FP
AL
01-95
96-99
Normal open function: Open the door without fingerprint or card
verification on the lock, which is fit for meeting room and some
places free to in or out.
Enable: Verify any registered fingerprints or cards on lock and
press key.
Disable: Press key directly.
Normal Open Function
RFID Card Function: Enable this function the lock can read ID cards.
The battery lifespan can be doubled after disabling the RFID Card
Function.
Enable: Verify any registered fingerprint on lock and press key.
Disable: Verify any registered fingerprint on lock and press key.
RFID Card Function
Administrator
L100D II/L100II
Home & Business Smart Lock
User Manual
(V2.1)
OK
C
8
9
10
11
12
13
14
15
2
4
7
5
1
3
6
16
LED indicator
Fingerprint sensor
Card area
Mechanical key hole
Restart button
Rubber key cover
9V emergency power terminal
Battery box cover
Battery area
Add key
Delete key
Nixie tube
“OK” Confirm Key
“C” Cancel Key
Factory Debug Port
Mechanical key
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
-
-
Character Description
Description
Initialization Button
Initialize The Fingerprint Lock
Initializing the fingerprint lock means all of the user will be deleted
and back to factory mode.
Operation:
The Initialization Button is in the inside panel of the lock, and holding the
Initialization Button until the lock prompts the voice of initialization.
When initialization is completed, the fingerprint lock will restart automaticly.
Note: Fingerprint Lock Initialization must be supplied with power.
User Introduction
Register User (Register user without administrator.)
Structure
Before Connecting, operating or adjusting this product, please read the instructions completely.
Keep this manual you will need it again.
is registered trademark of Anviz Global Inc. in the United States and other countries. It cannot be used without the
permission of Anviz.
Status
LED
-1-
-2-
-3-
-4-
Delete User (Delete user without administrator.)
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”.
Pressing key.
1 2 3
OK
When the Nixie tube flashes,
please press and key to
select “FP”, “AL” or “ID
number and press .
4
1
2
3
4
5
6
Activation status.
Activation status.
Place same finger or swipe same card again.
Delete user status / low battery voltage alarm.
Place same finger or swipe same card again to delete.
Unregistered finger or card .
Need administrator verify.
The Buzzer status
DescriptionStatus Buzzer
1
2
3
4
5
The lock under initial states and be activated.
Enable or Diable work mode.
Finger or Card Verification failed.
Operation succeedful.
Delete all the user / low battery voltage alarm.
Place finger in the center of the sensor.
Place finger flat on the sensor surface.
The Nixie tube will display
normal user ID: 01. Please
press and key to select
and press to enter the
registration status.
(User ID range is 01-95)
4
OK
OK
Next ID number will be
displayed after successful
registration.
Press to continue register
user or press key to exit
register status.
6
C
* Note:
One ID only can register one fingerprint or one card.
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”.
1 2
5
3
Place one user finger twice
on the fingerprint sensor or
swipe card on the card area
twice.
Pressing key.
OK
OK
C
If "FP" selected, Press key need to place finger twice on the sensor
or swipe card twice to delete. Press key to continue delete other
users or press key to exit delete status.
5
OK
If "AL" selected, Press key after six beeps form the lock all of the
normal users will be delete. The lock will auto logout deletion status.
OK
C
If "ID" selected, press to delete the appointed user. Press key to
exit delete status or press and key to continue select ID number
delete the appointed user.
-5-
-6-
-7-
-8-
-9-
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”. Hold key for 3 sec. Then it shows “Ad“.
Please verify Admin FP or
swipe Admin card to enter
the registration status.
It shows “ID” number, press
or key to select ID then
press to confirm.
Place one user finger twice on
the fingerprint sensor or swipe
card on the card area twice
(Please enable card function).
Next ID number will be
displayed after successful
registration.
Press to continue register
user or Press key to exit
registration status.
1 2 3 4
5 6 7 8
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”. Pressing key.
Then it shows “Ad’’
Please verify Admin FP or
swipe Admin card to enter
the registration status.
The Nixie tube will display
normal user ID: 01. Please
press and key to select
and press to enter the
registration status.
(User ID range is 01-95)
Place one user finger twice on
the fingerprint sensor or swipe
card on the card area twice.
Next ID number will be
displayed after successful
registration.
Press to continue register
user or press key to exit
exit register status.
1 2 3 4
5 6 7 8
OK
OK
C
C
-
-
-
-
-
* Note:
One ID only can register one fingerprint or one card.
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”.
1 2
5 6
3 4
Place one Admin finger twice
on the fingerprint sensor or
swipe card on the card area
twice.
Next ID number will be
displayed after successful
registration.
Press to continue
register user or press key
to exit register status.
C
When it shows admin ID:
96, press or to select
ID then to confirm.
(range : 96-99)
OK
Hold key for 3 sec.
Register First Administrator (The first time uses lock to register administrator.)
Register other Administrators
Register Normal User
Delete User
Delete Administrators
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”.
Pressing key.
Then it shows “Ad’’
Please verify Admin FP or
swipe Admin card to enter
the registration status.
OK
When the Nixie tube flashes,
please press and key to
select “FP”, “AL” or “ID
number and press .
1 2 3 4
5 6
Remove the battery box cover.
Press any key to activate the
lock.
The Nixie tube shows “--”. Hold key for 3 sec.
Then it shows “Ad’’
Please verify Admin FP or
swipe Admin card to enter
the registration status.
When the Nixie tube flashes
please. press and key to
select “FP”. “AL” or “ID
number. Then press .
1 2 3 4
5 6
OK
OK
OK
OK
Normal Operation Mode
7
OK
If "AL" selected, Press key after six beeps form the lock all of the
administrators will be delete. The lock will auto logout deletion status.
OK
C
If "ID" selected, press to delete the appointed administrator. Press
key to exit delete status or press and key to continue select ID
number delete the appointed administrator.
OK
OK
C
If "FP" selected, Press key need to place administrator finger twice
on the sensor or swipe card twice to delete. Press key to continue
delete other administrator or press key to exit delete status.
7
OK
OK
C
If "FP" selected, Press key need to place finger twice on the sensor
or swipe card twice to delete. Press key to continue delete other
users or press key to exit delete status.
OK
If "AL" selected, Press key after six beeps form the lock all of the
normal users will be delete. The lock will auto logout deletion status.
OK
C
If "ID" selected, press to delete the appointed user. Press key to
exit delete status or press and key to continue select ID number
delete the appointed user.
  • Page 1 1
  • Page 2 2

Anviz L100D II User manual

Type
User manual

Anviz L100D II is a Home & Business Smart Lock that can be operated by fingerprint, card, or mechanical key. It can store up to 95 normal users and 4 administrators, making it suitable for small businesses or families. The lock has a low battery voltage alarm and can be powered by four alkaline AA batteries. It also features a normal open function, which allows the door to be opened without fingerprint or card verification, making it ideal for meeting rooms or other places where free access is required. Additionally, the lock can be initialized to factory mode to delete all users.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI