Anviz S3 User manual

Anviz
Brand
Anviz
Model
S3
Type
User manual

Anviz S3 is a fingerprint keypad safe module that offers a range of features and use cases for enhanced security and convenience. With its standard 8 user design, it allows for multiple authorized individuals to access the secured area or device. The fashionable white LCD provides a clear and user-friendly interface for easy operation and status updates.

The Anviz S3 is equipped with an advanced optical sensor and BioNANO V10 algorithm, ensuring highly accurate and reliable fingerprint identification. It boasts an impressive FRR of 0.001% and FRA of 0.00001%, minimizing false rejection and acceptance rates. The 500 DPI resolution and 0.5-second identification time further enhance the user experience, providing quick and seamless access.

Anviz S3 is a fingerprint keypad safe module that offers a range of features and use cases for enhanced security and convenience. With its standard 8 user design, it allows for multiple authorized individuals to access the secured area or device. The fashionable white LCD provides a clear and user-friendly interface for easy operation and status updates.

The Anviz S3 is equipped with an advanced optical sensor and BioNANO V10 algorithm, ensuring highly accurate and reliable fingerprint identification. It boasts an impressive FRR of 0.001% and FRA of 0.00001%, minimizing false rejection and acceptance rates. The 500 DPI resolution and 0.5-second identification time further enhance the user experience, providing quick and seamless access.

1
Fingerprint Keypad Safe Module
S3
2
Operation
FEATURE
● Standard 8 user design
● Main board can drive electric motor, electromagnet.
●
Fashionable white LCD
●Hotel and home mode available
Parameter:
Sensor: AFOS300 Optical Sensor
Algorithm: BioNANO V10
LCD：
128*64 white LCD
Fingerprint Capacity:8
FRR: 0.001%
FRA: 0.00001%
Scan Area: 22mm*18mm
Resolution: 500 DPI Front panel：
Identification Time:<0.5 Sec
Main panel：
LCD：Connect LCD flat cable with front panel
LED: Power LED
Keypad: Connect Keypad flat cable with front panel
Fingerprint sensor: Connect with fingerprint sensor.
Power: 6V (4 AA batteries)
Emergency Power: For
external power
Initialization: Initialization device
Alarm: connect with alarm bell
Close door test: Connect with Exit button on the front panel
Bolt control: control flexible sport of bolt.
Motor:
drive motor
Mechanical Part：
3
Front board operation:
1. Battery Please use 4 AA batteries.
2. Factory mode: Press “START” to active the system and press any fingerprint on the scanner to drive the motor.
3. There are administrator and normal user
Administrator: Add and Delete normal user, Open the door
Normal user: Open the door
Family Mode
Add User:
The No.1 and No.2 user will default as administrator.
Press “START” to activate the system. Then press “ADD” key
Cap.
ADD ADMIN.
Place Finger
Place finger and remove after one beep sound. If not remove finger at once, buzzer will shout continuously.
4
Place Finger Again
ADD ADMIN.
Cap.
Place you finger again and with two beep sound for one second, the registration is successful;
Cap. OK
ADD ADMIN.
Place another finger to register other administrator fingerprints. Wait 5 seconds to return to sleeping mood.
Register normal user
Press “START” to activate the system. Then press “ADD” key
Admin. Place Finger
ADD
Cap.
Then need verified administrator’s fingerprint to register normal user. Please follow above steps.
Delete Normal User
Press “START” to activate the system. Press “DEL” key
Cap.
DEL.
Admin. Place Finger
Then press administrator fingerprint to delete all of normal user.
Delete Administrator User
After all normal users have been deleted. Follow above steps press administrator fingerprint to delete admin user.
5
Initialization system
Hold “START” and “Initialization” key. Then the system with three beeps the system initialize success.
Open Operation:
Press “START” to activate system and fingerprint sensor light. Place finger and two beeps sounds indicate successful
verification.
Cap. Granted!
WELCOME
Close Operation:
Press “START”, door will be closed automatically.
Hotel mode:
Please check the system without any user before you use it. You can press “START” and check the screen shows as follow:
Cap.
ADD USER
Place Finger
If the LCD shows “Cap. 1/1” you need Initialization system.
Operation steps:
Close
1、 Close the door or push out the bolt.
Cap.
ADD USER
Place Finger
6
2、 Press “START” key and screen show as follow:
Place finger and remove after one beep sound. If not remove finger at once, buzzer will shout continuously.
Cap.
Place Finger Again
ADD USER
Place you finger again and with two beep sound for one second, the registration is successful;
3、 After locked the system will in sleep mode.
Open
1、 Press “START” screen show as follow:
Cap.
WELCOME
Place Finger
2、 Press registered fingerprint the door will open or bolt will take back. And delete fingerprint. The system into original state.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Anviz S3 User manual

Anviz
Brand
Anviz
Model
S3
Type
User manual

Anviz S3 is a fingerprint keypad safe module that offers a range of features and use cases for enhanced security and convenience. With its standard 8 user design, it allows for multiple authorized individuals to access the secured area or device. The fashionable white LCD provides a clear and user-friendly interface for easy operation and status updates.

The Anviz S3 is equipped with an advanced optical sensor and BioNANO V10 algorithm, ensuring highly accurate and reliable fingerprint identification. It boasts an impressive FRR of 0.001% and FRA of 0.00001%, minimizing false rejection and acceptance rates. The 500 DPI resolution and 0.5-second identification time further enhance the user experience, providing quick and seamless access.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents