Dragonfly DF-103-AW-235 Owner's manual

Brand
Dragonfly
Model
DF-103-AW-235
Type
Owner's manual
Care and cleaning
•Yournewscreencanbeeectivelycleanedwithasoftcloth
using mild soap and water. DO NOT use harsh detergents,
chemicals, distilled spirits or petro-chemicals to clean the
screen;doingsomayresultinseveredamagetothescreenor
theframecoating.
•Ifthefeltcoveringontheframegetsdustyorcoveredwith
lint,useahouseholdvacuumcleanerwithabrushorfurniture
cleaningattachmenttocleanthefelt.Wedonotrecommend
usingexcessiveamountsofwateronthefelt.
A B C D E F
DF-SL-92-AW 92” 45.08'' 80.2'' 51.42'' 86.54'' 51.3’’
DF-SL-100-AW 100” 49.02'' 87.17'' 55.35'' 93.5'' 55.24’’
DF-SL-106-AW 106” 51.93'' 92.36'' 58.27'' 98.7'' 58.15’’
DF-SL-110-AW 110” 53.9'' 95.87'' 60.24'' 102.2'' 60.12’’
DF-SL-120-AW 120” 58.82'' 104.57'' 65.16'' 110.9'' 65’’
FixedFilmScreenwithBlackVelvetFrame
Assembly &
Installation
Instructions
4
”
4”
Top Bracket
Bottom Bracket
Security Clip
Pre-measured
Tether
•Thescreenisequippedwithasetofpre-measuredtethered
mounting brackets. There are security clips in the bottom
bracket. The screen should sit centered on the mounting
bracketwheninstalled.
•Drywall/Stud Installation:Usingastudnder,locatestudsin
wall. Hang top bracket rst (subtracting 1/2” from top of
screentomarkcorneredgeoftopofbracket)with5X40mm
Philips head screws and washers directly into studs. Pre-
drillingstudswitha5/32”drillbitisrecommended.
•Letthebottombracketdropand,whilepullingtetherstaut,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracketshouldbeused.
•Concrete Installation:Hangtopbracketrst(subtracting1/2”
from top of screen to mark corner edge of top of bracket).
Pre-drill3holesintoconcretewith1/4”concretebitandinsert
concreteanchors.Positiontopbracketoverholesandinsert
5X40mmPhilipsheadscrewsandwashers.
•Letthebottombracketdropand,whilepullingtetherstaut,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracketshouldbeused.
• Start by lifting screen frame onto top bracket, letting the
bottomrestagainstbottombracket.Carefullyliftbottomof
screen onto bottom bracket (Figure A & B). Security clips
willlockbottomofscreeninplace.Installationiscomplete.
•To release, simply push in clips and carefully lift bottom of
screenupandawayfromwall.
Drywall
Concrete
B
A
BlackAcousticallyTransparentMaterial(Optionalinstallation)
•Lightreectioncanbeanissuewithanyacoustically
transparentmaterial.Ifpaintingreectivesurfacesisnot
anoptiontocontrollightreection,anacoustically
transparentblackfabrichasbeenincluded.Simplyhang
thefabricdirectlybehindthescreeninanymannerthat
tsyourinstallation.
withAcoustiWeave™
E
D
B
A
F
C
Pleasefollowtheassemblyandinstallationinstructions
carefully. With proper assembly and installation, your
newscreenwilldeliveryearsoftrouble-freeservice
Preparingyourscreenforinstallation
PartList
•Carefullyopenthepackageandlayoutallthepartsonaclean,
atsurface
•Useextremecautionwhenunpackingthescreen;donotuse
knivesorsharpobjectstoopenthepackingboxes.
•Donotunpackthescreenmaterialatthistime.
AluminumFrameTube
TensioningRod
“L”Bracket
Assemblyx4
Acoustic
Material
SnapLugx34
Washersx8
TopandBottomBracketwith
Pre-measuredTetherx1each
5x40mmPhillips
HeadScrewsX8
Concrete
Anchorsx8
x2
x2
x2
x2
Installingthesnaplugs
•Slidethesnaplugsintothesectionoftheextrudedaluminum
frameasshowninDiagram1.
a
Snap Lug
b
• The snap lugs line up with the arrow decals on the frame
tubes.Alignmentisnotcriticalatthisstageoftheinstallation.
Notethatthescreenissuppliedwith2extrasnaplugs;should
youloseorbreakasnaplug,oneofthesparesisaconvenient
replacement.
Installingthescreenmaterial
•Placealloftheframetubesfacedownontheworksurfaceand
carefully line up the ends to form shape of the nished
screen.
•The4supplied“L”shapedcornerbracketassembliesareused
tojointheindividualframetubestogether.
• Loosen the 4 screws on the “L” brackets. Next, carefully
slipthebracketsintothealuminumframechannelasshown
indiagram2.
•It willhelptoleavethescrewslooseuntilyougetallofthe
bracketsinplace.
• Carefully line up the frame corners and tighten the screws
slightly;repeatthisstepateachcorner.
• Note that you may have to loosen and adjust the brackets
andframetubesinordertogettheframeperfectlysquare.A
carpenters square is very helpful with this stage of the
assembly.
•Once the screen is in place and the tensioning rods are
seated behind all of the snap lugs, inspect the front
of the screen. Make sure that the screen material is at
and wrinkle-free. Also, check the corners to make sure that
the screen is properly positioned. If there are any wrinkles
or positioning issues, simply lay the screen face down and
adjustaccordingly.
•Notethatsomeverysmallfoldlinesorwrinklesmayexist
forafewhours;thisisduetothepackingofthescreenand
theywilldisappearwithinashorttime.
•Makesurethathandsandworkareaarecleanbeforeworking
withthescreenmaterials
• Carefully unpack the screen material- Use caution as the 4
tensioningrodsarecontainedinsidethecardboardtube.
• Carefullylay out thescreenmaterial so that itroughly lines
upwiththeframe-Exactpositionisnotcriticalatthisstageof
theassembly.Itisimportantthatthescreenmaterialisfacing
thecorrectdirection.Itiseasytoidentifythebacksideofthe
screenasitwillhavethestitchedorweldedseamvisible.
•Unpackthe4metaltensioningrods.
•Insertthelongmetaltensioningrodsintothelongeredges
of the screen material, one rod per side. It is easier if the
screen is at on the oor. Use carewhen installing the rod;
donotforceitordamagetothescreenmaterialmayoccur
(SeeDiagram3).
• Insert the shorter tensioning rods into the corresponding
sides of the screen; as with the longer rods, use caution to
avoiddamagetothescreen(SeeDiagram3).
•Lineupthesnaplugsandthescreenmaterialwiththeframe
and press the snap lug through the corresponding hole in
the material. Some adjustment and re-adjustment is often
necessary;thisisnormal.Notethatthetensioningrodgoesto
theoutsideofthesnaplug(SeeDiagram4).
• Repeat this process all the way around the frame. As you
positionthetensioningrodbehindthesnaplugs,
the screen will become tighter on the frame and any
wrinkles or creases will disappear. It may also be helpful or
necessarytotemporarily“unsnap”orloosenthesnaplugfor
adjustment,especiallyasyouworktothenalcornersofthe
screen.
Assemblingtheframe
b
d
c
a
topframe
stripnuts
sideframe
L Bracket
Diagram1
Diagram2
Diagram3
TensionRod
a
c
b
Diagram4
a
b
c
d
e
TopFrameBar
Side
Frame
Bar
TopBracket
screen
FrontView
BackView
Side
View
TopView
Bottom Bracket
screen
screen
screen
Mountingthescreenontothewall
•Selectanappropriateareatomountthescreen.Makesurethe
position selected will not interfere with existing features of
yourroom;wallsockets,switches,etc…theseall should be
avoided.
•DONOTinstallthescreenoveranelectricaloutletorswitch.
Doingsoposesaseriousrehazard.
• For homes with stud-wall construction, use stud nder or
carefullymeasuretodeterminewherethestudsarelocatedin
thewall.ThescreenMUSTbemountedtothestuds-NEVER
rely on gypsum board, drywall, or thin wall materials to
supporttheweightofthescreen!
  • Page 1 1
  • Page 2 2

Dragonfly DF-103-AW-235 Owner's manual

Brand
Dragonfly
Model
DF-103-AW-235
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents