Lopi 564 User manual

Lopi
Brand
Lopi
Model
564
Category
Fireplaces
Type
User manual

This manual is also suitable for

Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 1 of 6 8/17/07 © Travis Industries, Inc.
Compatibility:
• 564 SS Fireplace
• 564 Electric Fireplace
Packing List:
• Face
• 564 SS Glass Frame Cover • 564 E Side and Hinge Brackets
• (2) 564 SS Top Brackets (w screws) • 564 E Upper Heat Shield
• (2) 564 SS Upper Mounting Brackets • 564 E Cove Cover
• (2) 564 SS Lower Mounting Brackets • (14) 8-32 Nuts
• (2) 10-24 1-1/2" Screws (564 SS only)
The center deflectors must be in place when using this face to prevent
the facing above the fireplace from becoming too hot. If this face is
replacing a Lopi Grill (96200801), make sure to replace the center
deflectors.
Installation Details – 564 SS
SIDE OF FIREPLACE
1”
0” TO 1”
NOTE:
This face has an adjustable bracket that allows for
different facing depths to be tucked under the face.
36”
29"
Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 2 of 6 6/24/08 © Travis Industries, Inc.
Installation – 564 SS
1 Remove the glass frame (see
the owner's manual for
details). Install glass frame
cover as shown to the right.
2 Install face mounting brackets
to the fireplace.
Push these tabs inwards
to lock the cover in place.
Place the cover over the top of the door frame.
Repeat these steps for the opposite side.
Upper
Bracket
Lower
Bracket
Upper
Left
Lower
Left
Upper
Right
Lower
Right
Bracket
Identification
Remove and discard the nuts and bushings
above and below the firebox.
Place the upper and lower brackets in place
and secure using the nuts included with this
kit.
Discard the stock
bushings and nuts.
Discard the stock
bushings and nuts.
Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 3 of 6 8/17/07 © Travis Industries, Inc.
Installation – 564 SS (continued)
3 The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation
manual for complete details.
Raised
Fireplaces
Note how the tile is 1”
(maximum) above the
base of the fireplace.
Maximum 1`” Hearth
Floor-Level
Fireplaces
Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 4 of 6 8/17/07 © Travis Industries, Inc.
Installation – 564 SS (continued)
4 Install the face following the directions below.
Attach the upper brackets
to the face with the
included nuts. The upper
bracket consists of two
pieces - note orientation.
Slide the face into place. The
tabs on the upper brackets insert
into the slots on the fireplace
brackets, holding the face in place
while the screws are tightened.
a
b
c
The face is secured to the fireplace with four screws. Two
of the screws are fastened to the upper brackets with
press nuts. The lower screws are included with the face.
Optional Facing (and/or hearth) --
See the installation manual for details.
Plated Surfaces
Use denatured alcohol and a soft cloth to clean plated surfaces. Marks
left on the surface may damage the face.
Denatured
Alcohol
Soft Cloth
Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 5 of 6 8/17/07 © Travis Industries, Inc.
Installation – 564 Electric
1 Install the upper heat shield onto the 564 E fireplace.
Remove the stock upper heat shield.
Place the upper heat shield included with this kit
on top of the fireplace (note position of heat
shield). Place the stock heat shield on top of it
and secure with the same screws.
Bostonian (564) Wilmington Face
Black 95400186 Nickel 95400187
Page 6 of 6 8/17/07 © Travis Industries, Inc.
2 Place the face, face down, on a soft, non-scratching surface. Install the 564 Electric mounting brackets onto
the back of the face.
a
Remove and
discard the
hinge assembly
from the face.
d
Attach the 564 E hinge bracket. Use
the nuts removed earlier.
Attach the 564 E side bracket.
Use the nuts included with
this kit.
Repeat steps “a” through
“c” for the opposite side.
e
Before installing the face
verify the lower grill is
centered. Loosen the nuts
and adjust if necessary.
b
c
3 Pull the electric fireplace out of the mantel (or built-in location). Attach the cove cover and face following the
directions below. Slide the fireplace back into place to complete the installation.
Tilt the face back slightly and insert the
bottom hooks into the slots on the fireplace.
Lift the face up slightly, tilt
it forward and insert the
top hooks until the face
locks in place.
b
c
Hang the 564 E cove
cover over the glass -
this keeps light from
exiting the grill opening
along the top of the face.
a
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Lopi 564 User manual

Lopi
Brand
Lopi
Model
564
Category
Fireplaces
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents