Polycom RealPresence Group Series Setting Up

Type
Setting Up
Setting Up the Polycom®
RealPresence® Group System
Tabletop Media Center
42” Display(s)
2
Codec Mounting Bracket
www.polycom.com
1725-68672-001/A
© 2014, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks associated with Polycom’s products are trademarks
and/or service marks of Polycom, Inc. and are registered and/or common law marks in the United States and various other countries.
All other trademarks are property of their respective owners.
M6 x 15 SEMS PPHS
(re-use)
Codec Bracket
M5 Knurled-
Head Screw (1)
M3 x 5 Phillips
Flat Head Screw (4)
M6 x 15 SEMS
PPHS (4)
Display Brackets (2)
1
Two Displays
M3 x 10 Phillips
Panhead SEM-INT
Screw (2)
M4 x 16 Phillips
Panhead
Screw (2)
M3 x 10 Phillips
Panhead SEM-INT
Screw (2)
Setting up the Polycom® RealPresence® Group System
Tabletop Media Center
2
23
2
M4 x 16 Phillips
Panhead
Screws (2)
5
M4 x 16 Phillips
Panhead
Screw (2)
M6 x 15 SEMS
PPHS
One Display
Two Displays
24
One Display
Two Displays
Setting up the Polycom® RealPresence® Group System
Tabletop Media Center
3
6
M3 x 5 Phillips
Flat Head Screw (4)
One Display
Two Displays
7
M5 Knurled-
Head Screw (1)
Setting up the Polycom® RealPresence® Group System
Tabletop Media Center
4
16
8
RPG 500 only
Two Displays
One Display
RPG 500 only
Only Polycom RealPresence Group System
components should be plugged into the power
outlet block. Do not power any other electrical
equipment from this power outlet.
Setting up the Polycom® RealPresence® Group System
Tabletop Media Center
5
16
Regulatory Notices:
This equipment is intended for indoor use only.
Only use this equipment with the display(s) supplied by
Polycom.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Polycom®
distributor or go to Polycom Support at
www.polycom.com/support.
Power Rating:
Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with Group
Series 500 codec and EagleEye IV camera under full
load operating conditions):
Single 42” display: 171.4W
Dual 42“ displays: 231.4W
Approximate system weight (including display(s),
codec, and camera):
Single 42” display: 62.7 lbs.
Dual 42” displays: 123 lbs.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Polycom RealPresence Group Series Setting Up

Type
Setting Up

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI