Miranda AMX-101i Manual To Installation And Operation

Brand: Miranda

Model: AMX-101i

Type: Manual To Installation And Operation

ELECTROMAGNETIC COMPATIBILITY

- This equipment has been tested for verification of compliance with FCC Part 15, Subpart

B, class A requirements for Digital Devices.

- This equipment complies with the requirements of EN55022 Class A, Electromagnetic

Emissions, En 60555-2 & -3, Disturbance in Supply Systems and EN50082-1,

Electromagnetic Immunity.

CONTACT MIRANDA

For technical assistance, please contact the Miranda Technical support centre nearest

you:

Americas

Telephone:

+1-800-224-7882

e-mail:

techsupp@miranda

.com

Asia

Telephone:

+81-3-5730-2987

e-mail:

asiatech@miranda

.com

Europe, Middle East,

Africa, UK

Telephone:

+44 (0) 1491

820222

e-mail:

eurotech@miranda

.com

France (only)

Telephone:

+33 (0) 1 55 86 87

e-mail:

francetech@miranda

.com

Visit our web site at www.miranda.com

CONTENTS

1 AMX-101i Analog Audio Multiplexer .....................................................1

1.1 Introduction ............................................................................................................. 1

1.2 Features.................................................................................................................. 1

2 Installation.............................................................................................2

2.1 Unpacking............................................................................................................... 2

2.2 AMX-101i Mechanical Installation........................................................................... 2

2.3 Rear Panel Label .................................................................................................... 3

2.4 AMX-101i Electrical Installation............................................................................... 5

2.5 600 Ω Internal Termination Jumper........................................................................ 6

3 Operation..............................................................................................7

3.1 AMX-101i User Interface......................................................................................... 7

3.2 Menu Introduction ................................................................................................... 8

3.3 Input Status Monitoring......................................................................................... 10

3.4 Audio Status Monitoring........................................................................................ 10

3.5 Audio Group Selection.......................................................................................... 11

3.6 Mute Selection ...................................................................................................... 11

3.7 Level Adjustments................................................................................................. 12

3.8 Groups Present Monitoring................................................................................... 12

3.9 Channel Swapping................................................................................................ 13

3.10 Audio Delay......................................................................................................... 13

3.11 Overwrite............................................................................................................. 14

3.12 Channel Status Bit Selections............................................................................. 14

3.13 Calibration........................................................................................................... 14

3.14 Factory Reset...................................................................................................... 15

3.15 Tone and Color Bar Generator Selection............................................................ 15

4 Specifications......................................................................................16

1 AMX-101i Analog Audio Multiplexer

1.1 Introduction

The AMX-101i is a high-quality, high-performance analog audio

multiplexer/embedder designed to insert two 20-bit sampled analog audio stereo

signals into a single SMPTE 259M-C serial digital video signal. The AMX-101i

has an on-board audio test tone signal and automatic 525/625 input detection

with full EDH monitoring.

The AMX-101i is a member of the imaging family of digital video modules and

therefore requires the imaging Quartet-A-75 or the imaging Symphonie frame with

Symphonie-R-A75 rear module for mounting and power.

1.2 Features

Input

§ Serial digital 4:2:2 input with active loop-through

§ 2 stereo/4 monaural analog audio inputs

§ Automatic 525/625 input detection

§ Input error detection and handling (EDH) monitoring

§ 250 m automatic cable equalization

Outputs

§ 3 serial 4:2:2 digital video outputs

§ EDH insertion on all serial 4:2:2 outputs

Processing

§ 20-bit high-quality analog to digital audio conversion

§ Digital de-emphasis filter

§ Channel status bit insertion

§ -7 to +24 dBu input level range

§ Right/left swap capability

§ Channel swap capabilities

§ Programmable audio delay (up to 10 frames)

§ Built-in audio test tone and color bar test signals

2 Installation

2.1 Unpacking

Make sure the following items have been shipped with the AMX-101i. If any of

the following items are missing, contact your distributor or Miranda Technologies

Inc.

§ AMX-101i Analog Audio Multiplexer

§ AMX-101i rear panel labels (2)

§ This manual

2.2 AMX-101i Mechanical Installation

Due to its audio inputs, the AMX-101i must be mounted within Quartet-A-75 or or

Symphonie imaging frames using Symphonie-R-A75 or Symphonie-R-A110 rear

modules. This section describes how to install the AMX-101i in any of these

frames. It is not necessary to switch off the power from these frames when

installing or removing the AMX-101i.

2.2.1 Quartet-A-75 Frame

To install this module into the audio Quartet frames follow these steps. For a

closer look at module installation and removal, refer to the frame's Guide to

Installation and Operation.

1. Remove the frame's front panel by rotating the thumb screws counter-

clockwise. Pull on the handles.

2. Select an empty slot.

3. Carefully place the AMX-101i between a set of module guides and gently

push the module towards the rear of the frame until the module's edge

connector is secured to the backplane. Pull lightly on the module verifying

that it does not move.

4. Replace the frame's front panel. Make sure to rotate the thumb screws

clockwise in order to secure it to the chassis.

2.2.2 Symphonie Frame

To install this module into the Symphonie housing frame, follow these steps. To

function, the AMX-101i requires the Symphonie-R-A75 or –R-A110 rear module.

For a closer look at module installation and removal, refer to the frame's Guide to

Installation and Operation.

1. Remove the front panel door by pulling on the door handles and gently

lowering it.

2. Select an empty slot.

3. Carefully place the module between the module guides and slowly push the

module towards the rear of the frame until the module's edge connector is

secured to its rear module. A light pressure to mate the connectors may be

required. Pull lightly on the module verifying that it does not move.

4. Replace the front panel door.

2.3 Rear Panel Label

A connector label has been shipped with the AMX-101i. This label is to be

installed on the frames’ rear panel in order to identify the module's external

connectors.

2.3.1 Quartet-A-75 Frame

To install the rear panel label on a Quartet-A-75 frame, follow these steps while

referring to Figure 2.1.

1. Remove the screws associated with the AMX-101i connectors.

2. Carefully apply the label to the connectors.

3. Replace the screws making sure not to damage the label.

Figure 2.1 Quartet rear panel label installation

AMX-101i ANALOG AUDIO MULTIPLEXER

AUDIO IN

Quartet-A-75 rear panel

IN 4:2:2 LOOP 4:2:2 OUT

1 2 3

2.3.2 Symphonie Frame

To install the Symphonie label, follow these steps while referring to Figure 2.2.

1. On Symphonie’s rear panel, locate the appropriate connectors.

2. Remove the rear label mounting screws from the rear module.

3. Carefully apply the label to the connectors making sure the label’s text is read

from top to bottom. Make sure to apply the label to the Symphonie-A75 rear

module.

4. Replace the screws making sure not to damage the label.

Figure 2.2 Symphonie rear panel label installation

Symphonie-R-A75

AMX-101i ANALOG AUDIO MULTIPLEXER

4:2:2 OUT AUDIO ININ 4:2:2 LOOP

1 2 3

Label

2.4 AMX-101i Electrical Installation

Refer to Figure 2.5 for rear panel electrical installation.

4:2:2 IN: serial digital video input with active loop-through

Connect a 4:2:2 serial digital video source to 4:2:2 IN. The AMX-101i accepts a

4:2:2 serial digital video signal in either 525 or 625-line format. This input must

conform to the SMPTE 259M-C standard. Make sure the input 4:2:2 cable has a

maximum length of 250 m (850'). Refer to section 3.3, Input Status Monitoring

for a description of error and EDH status on the input signal.

Make sure that all serial digital video connections are point-to-point. For instance,

there must be a point-to-point connection between the 4:2:2 IN BNC and the

source equipment. If a T-connector is used to connect other equipment, the

maximum specified cable length is no longer valid.

AUDIO IN: analog audio input

Connect 2 stereo or 4 monaural balanced analog audio signals to the AUDIO IN

connector. Figure 2.3 provides the pinout of the HD-15 rear panel connector.

Figure 2.3 AUDIO IN connector pinout (HD-15)

4:2:2 OUT 1, 2, and 3: serial digital video outputs

Serial digital video with inserted audio is provided by the 4:2:2 OUT 1, 2, 3

connectors. All outputs conform to the SMPTE 259M-C standard.

Gnd

Low

High

Low

High

Gnd

Low

High

Low

High

Right

Left

Stereo 2

Stereo 1

Figure 2.4 AMX-101i electrical installation (A75 rear panel)

2.5 600 Ω Internal Termination Jumper

When 600 Ω audio impedance equipment is connected to the AMX-101I, its input

impedance must be internally calibrated for 600 Ω. To do so, perform these

steps. It is necessary to use the imaging Extender Module to access the

potentiometers (refer to the frame’s Guide to Installation and Operation for more

information).

1. Referring to Figure 2.5 next page, install a jumper on the appropriate

connector LK1 through LK4. LK1, LK2, LK3, and LK4 correspond to inputs

R1, L1, R2, and L2 respectively.

2. Install the analog audio input.

3. Turn on the AMX-101i.

4. Using a technician's screwdriver, slowly tune the corresponding

potentiometer until the PEAK LED turns on. PEAK 1 LED is used to adjust L1

or R1 and PEAK 2 for L2 or R2.

5. Now, carefully reverse the tuning direction of the potentiometer stopping as

soon as the corresponding PEAK LED turns off.

6. Remove the jumper.

7. If you wish to calibrate all four inputs, repeat steps 1 to 6.

AMX-101i ANALOG AUDIO MULTIPLEXER

4:2:2 OUT AUDIO IN

SMPTE 259M-C 4:2:2 video

outputs multiplexed with

analog audio data

2 stereo or

4 monaural

analog audio

inputs

SMPTE 259M-C

4:2:2 video input

IN 4:2:2 LOOP

1 2 3

SMPTE 259M-C

4:2:2 video

loop-through

output

Figure 2.5 600 Ω jumper and potentiometer locations

3 Operation

3.1 AMX-101i User Interface

Figure 3.1 illustrates the AMX-101i's user interface situated at the front end of the

module. The interface components include the following:

§ Digital video input status monitoring

§ Analog audio input status monitoring

§ Test signal selection

§ 4-character dot matrix display and 4 push-buttons for menu and feature

access

Figure 3.1 AMX-101i user interface

LK4

AMX-101i

(top view)

LK3 LK2 LK1

L2 R2 L1 R1

Potentiometers

SELECT

AMX-101i ANALOG AUDIO MULTIPLEXER

TEST

525 625

ERR UES EDA EDH

INPUT

1 PEAK 2

ESC

AUDIO

3.2 Menu Introduction

Most AMX-101i parameters are accessed and changed via an easy-to-use menu.

The flow chart of Figure 3.2 outlines the entire AMX-101i menu path. The menu

consists of 10 major functions: audio group selection, mute, level adjustments,

group monitoring, channel swap, audio delay, overwrite, channel status mode,

calibration, and factory reset. Each menu is described throughout this section.

The following items should be remembered when accessing the menu.

Normal Mode

When the menu is not being accessed we refer to this as normal mode. When in

normal mode, the display is turned off.

Automatic Exit From Menu After 1-Minute Interval

If the menu is currently being accessed and no push-button has been pressed for

1 minute, the AMX-101i automatically exits from the menu thereby returning to

normal mode. Also, changes made to the current parameter will be stored.

Navigating Through the Menu

The front panel push-buttons are used to navigate the menu of Figure 3.2. The

following describes the function of each push-button when navigating through the

menu.

+: Press + to move down in the menu or to increase the parameter

value. For example, if you are currently at MUTE-L1, pressing + will

scroll downwards through the selections R1, L2, and R2. Depressing

+ during an adjustment will increase the parameter value at a faster

rate.

-: Press - to move up in the menu or to decrease the parameter value.

For example, if you are currently at SWAP, pressing - will scroll

upwards through the selections MONI, LEVL, MUTE, and GRP.

Depressing - during an adjustment will decrease the parameter value

at a faster rate.

SELECT: Changes to a menu parameter are stored immediately to non-volatile

memory. For example, after the desired R1 level has been set, press

SELECT. The menu returns to LEVL-R1 and the new level is stored

for the current format.

ESC: If ESC is pressed after making changes to a parameter, the

parameter is reset to the value it had prior to the change. For

example, after changing the L2 level, press ESC. The menu is

returned to LEVL-L2 and the previous level is reloaded.

Figure 3.2 AMX-101i menu hierarchy

AES

Home menu

(dB)

LR1

LR2

[NO,YES]

GRP

MUTE

SWAP

DELAY

CAL

[NONE,GRP1,GRP2,GRP3,GRP4]

[OFF,ON]

S - SELECT

E - ESCAPE

Figures in [] are varied using the front panel UP(+) and DOWN(-) push-buttons.

Words in () are the unit for the corresponding menu.

Underline indicates default value.

[NO,YES]

S E

EE S

S E

FACT

[NO,YES]

[OFF,ON]

EE S

LEVL L1

[0,0.5,1.0,...,30.5,31.0]

EE S

[0,0.5,1.0,...,30.5,31.0]

EE S

MONI [1234]

(dB)

[0,1,...,10]

CHAN LR1

E S

LR2

ALL

[OFF,ON]

EE S

ALL

[0,0.5,1.0,...,30.5,31.0]

EE S

(dB)

OVWR [ON, OFF]

STAT

EMPH

MODE

[PRO,CONS]

[NONE,5015,J17]

[2 CH, NONE,,MONO,STER]

STAT

EMPH

MODE

[PRO,CONS]

[NONE,5015,J17]

[2 CH, NONE,,MONO,STER]

3.3 Input Status Monitoring

§ 525

The 525 LED turns on to indicate a 525-line serial digital 4:2:2 signal has

been detected on the 4:2:2 IN BNC.

§ 625

The 625 LED turns on to indicate a 625-line serial digital 4:2:2 signal has

been detected on the 4:2:2 IN BNC.

§ ERR (Error)

The ERR LED will turn on if no input serial digital 4:2:2 signal is installed or if

an error has been detected within it. Make sure the source signal is properly

connected to 4:2:2 IN and verify for any source equipment errors.

§ UES (Unknown Error Status)

This LED turns on to indicate a serial digital video signal is received from

source equipment not supporting error detection and handling.

§ EDA (Error Detected Already)

This LED turns on to indicate a serial transmission data error has been

detected somewhere upstream.

§ EDH (Error Detected Here)

This LED turns on to indicate a serial transmission data error has been

detected.

3.4 Audio Status Monitoring

§ PEAK 1

This LED turns on when the analog audio stereo 1 input signal level is higher

than 24 dBU. In this case, the analog signal will be clipped and this will result

in losing part of the information contained in the audio.

§ PEAK 2

This LED turns on when the analog audio stereo 2 input signal level is higher

than 24 dBU. In this case, the analog signal will be clipped and this will result

in losing part of the information contained in the audio.

3.5 Audio Group Selection

The analog audio inputs can be embedded in any of four groups within the

horizontal ancillary data space (HANC) of the 4:2:2 digital video signal. If no

audio data is detected in the audio group, selected here, within the input 4:2:2

serial digital signal, then multiplexing is automatically performed. However, if

audio data is detected, you must specify with the Overwrite menu if you wish to

remove the detected audio data and replace it with the audio signals connected to

AUDIO IN. Perform the following steps in order to select the group in which the

audio shall be embedded.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press SELECT to enable the audio group selection menu. The current audio

group used to embed the audio input is displayed.

3. Press (+) or (-) to change the audio group selection. If you wish not to embed

any audio within the input video signal, select NONE.

4. Press SELECT to store the new audio group. GRP is displayed.

5. Press ESC to return to normal mode.

3.6 Mute Selection

Follow these steps to disable or enable any analog audio channel.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until MUTE is displayed.

3. Press SELECT to enable the MUTE menu. L1 is displayed.

4. Use the (+) or (-) push-button to scroll through the available audio channels.

Press SELECT. The current mute setup for the selected channel is

displayed.

5. Press (+) to select ON and to mute the audio channel or (-) to select OFF and

to disable muting.

6. Press SELECT to store the new mute setup for the audio channel selected in

step 4.

7. Press ESC to return to MUTE.

8. To return to normal mode, press ESC.

Note: To mute all channels, enable the menu MUTE-ALL and select ON.

3.7 Level Adjustments

This section describes the necessary steps to take in order to adjust the analog

audio input levels. Each input gain configuration L1, R1, L2 and R2 can be

individually set between 0dB and 31 dB. A 0 dB setting provides a full scale

output of 24 dBu. Each 0.5 dB step decreases the full scale output by 0.5 dBu for

a maximum of 31 dB. As an example, the position +31dB corresponds to a full

scale (0 dBFS) with an analog input of –7 dBu maximum.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until LEVL is displayed.

3. Press SELECT to enable the level menu. L1 is displayed.

4. Use the (+) or (-) push-button to scroll through the available audio channels.

Press SELECT. The current level, in dB, for the selected channel is

displayed.

If you wish to adjust all audio channels simultaneously, select the ALL option.

5. Use (+) or (-) to set the required level. For a quicker response, keep the

push-button depressed. Press (+) and (-) simultaneously to set the selected

level to the nominal value 0 dB.

6. Press SELECT to store the new level for the audio channel selected in step

4. If ALL was selected, the new level shall be stored for each channel.

7. Press ESC to return to LEVL.

8. To return to normal mode, press ESC.

3.8 Groups Present Monitoring

To view which audio groups are detected within the 4:2:2 input signal, follow

these steps.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until MONI is displayed.

3. Press SELECT to view the detected audio groups. If, for example, audio

groups 1, 3, and 4 are detected, the display will show "1 34".

4. Press SELECT or ESC to return to MONI.

5. To return to normal mode, press ESC.

3.9 Channel Swapping

The following swap combinations are provided by the AMX-101i.

AES: Channel pair swap between AES 1 and AES 2.

LR1: Swap the left and right channels of AES 1.

LR2: Swap the left and right channels of AES 2.

Perform the following steps in order to enable or disable a desired swap.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until SWAP is displayed.

3. Press SELECT to enable the swap menu. AES is displayed.

4. Use the (+) or (-) push-button to scroll through the available swap

combinations. Press SELECT. The current swap setting is displayed for the

selected swap combination.

5. Press (+) to select YES and to enable the swap or (-) to select NO and to

disable the swap.

6. Press SELECT to store the new swap setting for the swap combination

selected in step 4.

7. Press ESC to return to SWAP.

8. To return to normal mode, press ESC.

3.10 Audio Delay

It is possible to add an audio delay of up to 10 video frames, by steps of one

frame. To add audio delay, follow these steps:

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until DELAY is displayed.

3. Press SELECT to enable the delay menu.

4. Use (+) or (-) to set the desired delay. For a quicker response, keep the

push-button depressed. Press (+) and (-) simultaneously to set the delay to

the nominal value 0 dB.

5. Press SELECT to store the new delay.

6. Press ESC to return to DELAY.

7. To return to normal mode, press ESC.

3.11 Overwrite

The overwrite menu is used to enable or disable overwriting an existing audio

group within the input 4:2:2 serial digital signal with the input analog audio signals.

To enable or disable overwriting existing audio data with new audio data, perform

these steps.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until OVWR is displayed.

3. Press SELECT to view the current status of multiplexing. Press (+) to select

ON and to enable multiplexing or press (-) to select OFF and to disable

multiplexing.

4. Press SELECT to store the new status and to return to OVER.

5. To return to normal mode, press ESC.

3.12 Channel Status Bit Selections

This menu is used to insert channel status information in the AES bytes of the

4:2:2 output signal. Different selections are possible for each stereo channel.

STAT: Selects between the type of use, professional (PRO) or consumer

(CONS), of the channel.

EMPH: Selects between two types of emphasis standards: 50-15 us (5015)

and J17.

MODE: Indicates if the channel is non-stereo (MONO), stereo (STER), has

distinct left and right audio signals (2 CH) or has a primary and

secondary audio signal (P/S).

3.13 Calibration

It may be necessary at times to calibrate the analog -to- digital audio converters

(ADC). This calibration is entirely automatic and should be performed if

necessary for optimum ADC performance. Follow these steps to perform

automatic ADC calibration.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until CAL is displayed.

3. Press SELECT to enter the calibration menu. NO is displayed.

4. Press (+) to display YES. Press SELECT begin the ADC calibration. After

completing the ADC calibration, the AMX-101i returns to the CAL menu.

5. Press ESC to return to normal mode.

3.14 Factory Reset

It may be necessary, at times, to reset all parameters to their original values

programmed during manufacturing. Table 3.1 lists the default values. To

perform a factory reset follow these steps.

1. Press SELECT to enter the menu. GRP is displayed.

2. Press the (+) push-button until FACT is displayed.

3. Press SELECT to enter the FACT menu. NO is displayed.

4. Press the (+) push-button to display YES.

5. Press SELECT to reset all parameter values to factory values. After the reset

is complete, the AMX-101i exits to FACT.

6. Press ESC to return to normal mode.

Table 3.1 Parameter values after a factory reset

Group selection:

GRP1

Muting:

OFF for all channels

Level:

0 dB for all channels

Channel swapping:

Delay:

Overwrite:

Channel status:

Channel emphasis:

Channel mode:

NO or disabled for all channels

PRO (professional)

NONE

2CH

3.15 Tone and Color Bar Generator Selection

An internal tone generator provides a steady –18 dBFS 1 KHz continuous

sinewave on all channels. To enable the tone generator and the internal color bar

pattern, follow these steps:

1. Make sure the AMX-101i is in normal mode.

2. Press TEST(+) to enable the tone and color bar generator. During this time,

the TEST LED is on.

3. To disable the tone and color bar generator, press TEST(+). The TEST LED

turns off. The outputs are returned to their original status.

4 Specifications

Input

4:2:2 IN

Signal: SMPTE 259M-C serial 4:2:2 525/625@270 Mbps

with active loop-through

Cable length: 250 m (850’)

Return loss: >15 dB up to 270 MHz

ANALOG IN

Signal: 2 stereo/4 monaural balanced analog audio

Termination: 600 ohm/20 Kohm (jumper selectable)

Level range: -7 to +24 dBu

Output

4:2:2 OUT

Signal: SMPTE 259M-C serial 4:2:2 525/625@270 Mbps (3)

Return loss: >15 dB up to 270 MHz

Jitter: <0.2 UI (0.7 ns) p-p

Processing Performance

Quantization: 10-bits (video)

20-bits (audio)

Audio sampling: 48 KHz (128X oversampling)

Dynamic range: >110 dB (A weighting)

SNR: >110 dB (A weighting)

Distortion: <-100 dB (0.001%)

Crosstalk: <-105 dBFS (20 Hz to 20 KHz)

Pass band: ± 0.1 dB (20 Hz to 20 KHz)

Processing delay: 1.5 µs (video)

1.9 ms (audio)

Audio delay: 0-10 video frames

Audio jitter: <2ns p-p

Miscellaneous

Tone generator: Steady 1 KHz sine wave on each audio output

Storage temperature: -40 to 85°C

Operating environment: 0 to 40°C, non-condensing

Output timing drift: < 0.1 ns/°C

Humidity: 10 to 90%, non-condensing

Power consumption: 6 W

Physical format: imaging size (6.0”x10.0”)

Remote control: ICP-S (Miranda proprietary serial bus)

Miranda AMX-101i Manual To Installation And Operation

Miranda AMX-101i Manual To Installation And Operation

Miranda AMX-101i Manual To Installation And Operation

Related papers

Other documents