Definitive Technology MYTHOS SIXSTAND User manual

Definitive Technology
Brand
Definitive Technology
Model
MYTHOS SIXSTAND
Category
Speaker mounts
Type
User manual

Definitive Technology MYTHOS SIXSTAND is the only stand custom designed and engineered for Definitive Technology Mythos Six Loudspeakers. It features a hidden wire channel for prewiring, allowing for a clean and organized installation. The stand comes with both carpet spikes and rubber feet, making it suitable for use on both carpet and hard floors. The translucent bottom pad provides additional stability and helps to protect the floor from scratches.

Definitive Technology MYTHOS SIXSTAND is the only stand custom designed and engineered for Definitive Technology Mythos Six Loudspeakers. It features a hidden wire channel for prewiring, allowing for a clean and organized installation. The stand comes with both carpet spikes and rubber feet, making it suitable for use on both carpet and hard floors. The translucent bottom pad provides additional stability and helps to protect the floor from scratches.

The only stand custom designed and engineered for Definitive Technology Mythos Six Loudspeakers.
Parts:
•Post , including Top Cap, Pads, Speaker Screw , Hidden Wire Channel .
•Translucent Bottom Pad .
•Glass Base , including preattached Feet.
•Carpet Spikes, Rubber Feet .
•Bottom Assembly: Bolt Cover Skirt , Steel Insert , Cap Screws (2) .
•Hex Key.
Attach Post to Glass Base:
1. With Glass Base upside down (feet up), place the Bolt Cover Skirt open side up
(with curve matching base) over Screw Holes.
2. Place the Steel Insert into the Bolt Cover Skirt. Insert the Two Cap Screws
into this assembly.
3. Slide the Translucent Bottom Pad over Screws on the other side of the Glass Base.
This will hold the assembly in place.
4. Line up Hex Key with bottom of Post .
5. Secure assembly to Post by tightening the two Cap Screws firmly using the Hex Key.
Do not overtighten.
6. Attach Carpet Spikes (for use with carpet) or Rubber Feet (for hard floor use).
7. Set stand upright. Push Spikes (if used) into carpet for stability.
Attach Mythos Six Speaker to Stand:
1. Prewire the Mythos Six Stand Post using the hidden wire channel provided.
2. Make your wire connections to the Mythos Six Loudspeaker before attaching the
loudspeaker to the stand.
3. Remove the plastic plug from the Insert Nut on the rear of the Mythos Six
Loudspeaker.This is the small hole located above the connectors.
4. Position the Mythos Six Loudspeaker to accept the Mythos Six Stand’s Speaker Screw.
Insert a Hex Key through the Mythos Six Stand’s Post and tighten the Speaker Screws
into the Insert Nut, alternating between tightening each screw (if one screw is tightened
first, it will be difficult to tighten the other). Tighten securely, but do not overtighten.
Definitive Technology
MYTHOS SIXSTAND USER’S GUIDE
Mythos Six Loudspeaker front stage speaker setup: For best imaging performance,
create an equilateral triangle between the speakers and your listening position.
Aim speakers “in,” if necessary.
For more information on Definitive Technology Loudspeakers and accessories,
visit www.definitivetech.com, or email info@definitivetech.com.
Definitive Technology, Owings Mills, Maryland, USA. 410-363-7148
  • Page 1 1

Definitive Technology MYTHOS SIXSTAND User manual

Definitive Technology
Brand
Definitive Technology
Model
MYTHOS SIXSTAND
Category
Speaker mounts
Type
User manual

Definitive Technology MYTHOS SIXSTAND is the only stand custom designed and engineered for Definitive Technology Mythos Six Loudspeakers. It features a hidden wire channel for prewiring, allowing for a clean and organized installation. The stand comes with both carpet spikes and rubber feet, making it suitable for use on both carpet and hard floors. The translucent bottom pad provides additional stability and helps to protect the floor from scratches.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents