ROOTECH Accura 3300S User guide

ACCURA 3300S

High Accuracy Digital Power Meter

With full features of power measurements

Becomes a necessary solution to you,

Providing simultaneously display of voltage, current, power, and energy.

User Guide[Korean]

Rev 1.3 2016/09/05

Notice

Danger

Indicates the presence of dangerous voltage which can cause severe injury or death

to persons if proper precautions are not followed.

Warning

Alerts the user to the presence of hazards which can cause somewhat injury to

persons, damage to property or damage to the device itself, if proper precautions

are not followed.

Note

Indicates the user’s attention to installation, operating and maintenance instructions.

Electrical Symbols

Indicates alternative voltage or current.

Indicates direct voltage or current.

Installation Considerations

Installation and operation of Accura 3300S meter should be performed only by qualified,

competent personnel that have appropriate training and experience with high voltage and current

devices.

Danger

Failure to observe the following instructions may result in severe injury or death.

 During normal operation of the Accura 3300S meter, hazardous voltages are present

on its terminal strips.

 Standard safety precautions are followed while performing any installation or service

work[removing PT fuses, shorting CT secondaries, etc].

 Do not access to terminal strips of the Accura 3300S meter after installation.

Warning

Observe the following instructions, or permanent damage to the meter may occur.

 Do not apply Accura 3300S to voltages and currents that exceed Input ratings of PT and

CT.

Limitation of Liability

Rootech Inc. reserves the right to make changes in the device specifications shown in this User’s

Guide without notice. Rootech Inc. advises customers to obtain the latest specifications of device

before giving orders to confirm that the information being relied on by the customer is up to date.

In the absence of written agreement to the contrary, Rootech Inc. assumes no liability for Rootech

Inc. applications assistance, customer’s system design, or infringement of patents or copyrights of

third parties by or arsing from the use of devices described herein.

Except to the extent prohibited by applicable law, under no circumstances shall Rootech Inc. be

liable for consequential damages sustained in connection with said product and Rootech Inc.

neither assumes nor authorizes any representative or other person any obligation or liability other

than such as is expressly set forth herein.

The information contained in this document is believed to be accurate at the time of publication,

however, Rootech Inc. assumes no responsibility for any errors which may appear here and

reserves the right to make changes without notice.

Standard Compliance

CE Approved

EN61326 and IEC61010

MEASURING EQUIPMENT

35DX

E258934

QMS-1347

KAB-QC-09

Warranty Information

For products and software that are sold or licensed by Rootech Inc. during the period from the

date of receipt by you until the present, Rootech warrants only to the original purchaser

The purchased products other than software shall be substantially free from material defects in

material and workmanship by Rootech for two years from the date receipt by you.

The software itself is provided “as is” without any warranty of any kind.

Limitation of Warranty

These limited Warranties shall not apply to any product that has been subject to alteration,

accident, misuse, abuse, neglect or failure to exactly follow Power Measurement's instructions for

operation and maintenance.

In order for the original purchaser to make a claim under the warranties described above, the

original purchaser must promptly contact Rootech headquarter. After receiving such notice,

Rootech may either in Rootech’s sole discretion, examine the product at the original purchaser’s

site or issue shipping instructions to the original purchaser to return the relevant product to

Rootech for examination at the original purchaser’s expense, transportation charges prepaid.

If after examining the product Rootech reasonably confirms that such examined product does not

meet the warranties, then the original purchaser’s sole remedy and Rootech’s sole obligation or

liability shall be, at Rootech’s option, to repair, replace or refund the price paid for that product.

Regardless of whether any remedy set forth herein fails of its essential purpose, except to the

extent the following limitation is prohibited by applicable law, Rootech shall not, in any event or

under any legal claim or theory, be liable to the original purchaser or any other person or entity

for special, indirect, incidental, punitive, liquidated, special or consequential damages whatsoever

with respect to any purchased product, including, without limitation, business interruption, loss of

use, profit or revenue, even if Rootech has been advised of the possibility of such damages. To the

extent that a limitation or exclusion of consequential damages are prohibited by applicable law,

then Rootech’s liability shall be limited to twice the amount of the relevant purchased product.

Rootech shall not be liable for any claim- other than a claim solely for the breach of one of the

above warranties that is made in accordance with the above described procedures- made by the

original purchaser, its employees, agents, or contractors for any loss, damage, or expense

incurred due to, caused by, or related to any purchased product

Any technical assistance provided by Rootech's personnel or representatives in system design shall

be deemed to be a proposal and not a recommendation. The responsibility for determining the

feasibility of such proposals rests with the original purchaser and should be tested by the original

purchaser.

It is the original purchaser’s responsibility to determine the suitability of any product and

associated documentation for its purposes. The original purchaser acknowledges that 100% "up"

time is not realizable because of possible hardware or software defects. The original purchaser

recognizes that such defects and failures may cause inaccuracies or malfunctions.

Only the terms expressed in these limited Warranties shall apply and no distributor, corporation or

other entity, individual or employee of Rootech or any other entity is authorized to amend, modify

or extend the Warranties in any way.

Revision History

The following versions of the Accura 3300S User’s Guide have been are released.

Revision #

Revision date

Description

Revision 1.0

2008. 03. 05

Initial draft

Revision 1.1

2009. 11. 27

Voltage input range modified

Revision 1.2

2015. 05. 12

Standard compliance updated

Revision 1.3

2016. 09. 05

Voltage wiring diagram updated

Contents

Chapter 1 Introduction ............................................................................................................. 12

Overview ............................................................................................................................... 12

Power Measurements ..................................................................................................... 12

Accuracy ........................................................................................................................ 12

Power Quality ................................................................................................................ 12

CE/UL Safety and Reliability ........................................................................................... 12

Communication[IrDA and RS485] .................................................................................. 12

Features ................................................................................................................................ 14

Measurement ................................................................................................................. 14

Power Quality ................................................................................................................ 14

IrDA Communication ..................................................................................................... 14

Communication .............................................................................................................. 14

Power Supply ................................................................................................................. 15

Applications .......................................................................................................................... 15

True RMS Measurements robust to harmonics ................................................................ 15

Power Quality Analysis .................................................................................................. 15

Compatibility with Analog Meters .................................................................................. 15

High Reliability Energy Management ............................................................................. 15

Parameters ............................................................................................................................ 16

Chapter 2 Mounting ............................................................................................................... 17

Environmental Conditions .............................................................................................. 17

Enclosure Considerations ............................................................................................... 17

Before You Begin ................................................................................................................... 18

Meter Overview ............................................................................................................. 18

Meter Dimensions .......................................................................................................... 19

Step 1: Mounting ................................................................................................................ 20

Sequence ....................................................................................................................... 20

Step 2: Voltage and Current Inputs ..................................................................................... 21

Voltage Input ................................................................................................................. 21

Current Input ................................................................................................................. 22

Wiring Diagram Using External PTs ................................................................................ 23

Direct Diagram Using No PTs ......................................................................................... 26

Step 3: Wire the RS485 Communication ................................................................................ 29

Step 4: Wire the Power Supply and Ground Terminal ............................................................ 30

Power Supply ................................................................................................................. 30

Ground Terminal ............................................................................................................ 30

Step 5: Add a Cover/Power Up the Meter ........................................................................... 31

Add a Cover ................................................................................................................... 31

Power Up the Meter ....................................................................................................... 31

Chapter 3 Meter Operation/Setup .......................................................................................... 32

Display Mode ........................................................................................................................ 33

Setup Mode ........................................................................................................................... 39

Reset Mode............................................................................................................................ 41

System Mode ......................................................................................................................... 42

Reactive Calculation Method .......................................................................................... 44

APPENDIX A Standard Specification ........................................................................................ 46

APPENDIX B Standard Compliance ......................................................................................... 47

APPENDIX C Test Report ......................................................................................................... 48

Measuring Test ...................................................................................................................... 48

Reliability Test........................................................................................................................ 49

INDEX ..................................................................................................................................... 50

Figures

Fig 1.1 Accura PDA Software .......................................................................................... 13

Fig 2.1 Front Side ........................................................................................................... 18

Fig 2.2 Rear Side ............................................................................................................ 18

Fig 2.3 Front View .......................................................................................................... 19

Fig 2.4 Rear View ........................................................................................................... 19

Fig 2.5 Side View ........................................................................................................... 19

Fig 2.6 ANSI 4” .............................................................................................................. 20

Fig 2.7 DIN96 ................................................................................................................ 20

Fig 2.8 Voltage and Current Connector .......................................................................... 21

Fig 2.9 Single Phase 2 Wires, Wiring Mode = 1P2U ....................................................... 23

Fig 2.10 Three Phase 3 Wire Open Delta Using 2CTs, Wiring Mode = 3P3O ................. 24

Fig 2.11 Three Phase 3 Wire Open Delta Using 3CTs, Wiring Mode = 3P3O ................. 24

Fig 2.12 Three Phase 4 Wires Using 3 PTs and 3 CTs, Wiring Mode = 3P4U .................. 25

Fig 2.13 Single Phase 2 Wire Direct , Wiring Mode = 1P2U ........................................... 26

Fig 2.14 Single Phase 3 Wire Direct Using 2 CTs, Wiring Mode = 1P3U ......................... 27

Fig 2.15 Three Phase 3 Wire Open Delta Direct, Wiring Mode = 3P3O ......................... 27

Fig 2.16 Three Phase 3 Wire Open Delta Direct Using 3 CTs, Wiring Mode = 3P3O ...... 28

Fig 2.17 Three Phase 4 Wire Direct Using 3 CTs, Wiring Mode = 3P4U ......................... 28

Fig 2.18 Communication Wiring .................................................................................... 29

Fig 2.19 Wiring of Power Supply and Ground Terminal ................................................. 30

Fig 2.20 Cover ............................................................................................................... 31

Fig 3.1 Measurement Group A, B ................................................................................... 33

Fig 3.2 Measurement Group C ....................................................................................... 33

Fig 3.3 Measurement Group D ....................................................................................... 33

Fig 3.4 x1000, x10 LED .................................................................................................. 34

Fig 3.5 P, Q[according to general calculation] ................................................................ 44

Chapter 1 Introduction

Overview

Power Measurements

Accura 3300S is a high accuracy digital power meter, suited to power measurements. The device

is applied to a variety of applications, electrical facilities, intelligent building system, factory,

generator and etc, making measurements of voltage, current, power, frequency, power factor, and

demand.

Accuracy

The measuring accuracy is the most important criterion to evaluate the reliability of energy

management system. Actually low accuracy makes it hard for customers to precisely manage

energy, causing inequality of energy between incoming feeder and sum of load sides. Accura

3300S makes 0.2% high accuracy measurements for voltage and current, and conforms to

IEC62053-22 class 0.5S for power and energy. This makes it possible to solve the problem with

energy inequality.

Power Quality

Accura 3300S provides the information of power qualities, such as voltage/current THD, harmonic

analysis, and k factor.

CE/UL Safety and Reliability

The structure- framework, circuit, fire - of Accura 3300S conforms to safety standard,

CE[IEC61010], UL[UL61010-2, 2nd edition]. Particularly the device provides pass-through busbar,

allowing CT leads to be terminated on the device. This eliminates any possible point of failure at

the device.

Communication[IrDA and RS485]

Accura 3300S provides two independent communication ports. One port provides RS485

communication which supports a variety of applications, such as energy management, IBS, and

SCADA. The Accura also has an optical IrDA port, allowing the device to be set up and

programmed using a PDA. Just point at the meter with IrDA-equipped PDA, so customers can

monitor measurements, harmonic graph, vector diagram, demand trend, and oscilloscope.

Rootech provides ‘Accura PDA software” that allows users to simply point at the meter, configure it

and poll readings. See the Accura 3300S Communication User’s Guide for details.

Fig 1.1 Accura PDA Software

Features

Measurement

 64 Sampling/Cycle True RMS

 IEC 62053-22 Class 0.5S

 50, 60Hz

 Energy stored periodically to non-volatile memory.

 4 Quadrant Energy

 kWh/kVARh received1, kWh/kVARh delivered1

 kWh/kVARh net[kWh/kVARh received - kWh/kVARh delivered]

 kWh/kVARh total[kWh/kVARh received + kWh/kVARh delivered]

 Phase voltage, line to line voltage, current

 Active power, reactive power, active energy, reactive energy†, power factor, frequency

 Fundamental component†, True RMS of current

 4 Quadrant Power

 Demand, peak demand

 Maximum, Minimum†

1kWh/kVARh received is positive for “view as load”, kWh/kVARh

delivered is positive for “view as generator”.

Power Quality

 Voltage/current THD

 Harmonic Analysis†

 K factor†

†It is available only on RS485 communication.

IrDA Communication

 Harmonic graph

 Vector diagram

 Demand trend

 Oscilloscope

Communication

 RS485 Port[rear]

Modbus RTU Protocol

Baudrate: 1,200 ~ 57,600bps

 IrDA Port[front]

Power Supply

 AC 85 ~ 265V, 50/60Hz

 DC 100 ~ 300V

 Burden: 10VA

Applications

True RMS Measurements robust to harmonics

Most of energy environments consist of nonlinear loads, such as industrial load, rectifier, power

electronic device, electric furnace and etc. this causes fatal distortion of voltage and current

waveforms. Accura 3300S makes high accuracy True RMS measurements for voltage and current

distorted with harmonics.

Power Quality Analysis

Accura 3300S provides k factor, analysis of voltage and current up to 31st harmonic, and realtime

waveform of voltage and current.

Compatibility with Analog Meters

Accura 3300S mounts directly in ANSI C39.1[4” Round] or DIN 96. this is perfect for new

installations and for existing panels. In new installations, simply use existing DIN or ANSI punches.

For existing panels, pull out old analog meters and fit the device in its cutout.

High Reliability Energy Management

The most important point to evaluate the overall data reliability of energy management is the

accuracy of meters. Accura 3300S makes 0.2% high accuracy measurements for voltage and

current, and conforms to IEC62053-22 class 0.5S for power and energy. Energy management

gives customers various services, monitoring, cost curtailment, demand, energy planning, and etc.

Parameters

Realtime1

Average2

Total3

Maximum4

Minimum5 †

Phase voltage

■

Line to line voltage

■

Current

■

Power

Active

■

Reactive

■

Apparent†

■

Energy6

Active

■

Reactive†

■

Apparent†

■

Frequency

■

Power factor

■

THD

Voltage

■

Current

■

Demand

Power

■

Current

■

1Instaneous measuring. 2Average of three phase parameters. 3Total sum of three phase parameters.

4If realtime measurements exceed maximums, the maximums will be updated.

5If realtime measurements is less than minimums, the minimums will be updated.

6Energy is periodically stored to non-volatile memory. †It is available only on RS485 communication.66

Note

The Maximums and minimums will not be updated with no power-up.

All of the measurements are not shown for 5 seconds after power-up.

Chapter 2 Mounting

Environmental Conditions

The Accura 3300S should be mounted in a dry, dirt free location away from heat sources and very

high electric fields. To operate properly and effectively, environmental conditions should range

within the following guidelines

Items

Acceptable Range

Position

Indoor use

Operating Temp

-20 ~ 70C[-4℉ ~ 158℉]

Storage Temp

-40 ~ 85C[-40℉ ~ 185℉]

Operating Humidity

5 ~ 95% Non condensing

Enclosure Considerations

The enclosure the Accura 3300S is mounted in (typically a switchgear cabinet) should protect the

device from atmospheric contaminants such as oil, moisture, dust, and corrosive vapors, or other

harmful airborne substances. The mounting enclosure should be positioned such that the doors

may be opened fully for easy access to the Accura 3300S wiring and related components to allow

for convenient troubleshooting.

Warning

The meter should be installed in a switchgear cabinet or similar enclosure to ensure the terminal

strips on the meter base are not user accessible after installation.

Mount the meter in a dry location free from dirt and corrosive vapors. Once installed, no cleaning

of the device is necessary.

Before You Begin

Before installing the meter, observe the instructions in this guide and read the safety precautions

presented on the “Installation Considerations” page.

Danger

Power up after the voltage and current wiring is completed.

Meter Overview

Fig 2.1 Front Side

Fig 2.2 Rear Side

Meter Dimensions

Fig 2.3 Front View

Fig 2.4 Rear View

Fig 2.5 Side View

Step 1: Mounting

Sequence

1. Remove connector on the bottom of the meter.

2. fit the meter into cutout[ANSI 4” or DIN96]

Fig 2.6 ANSI 4”

Fig 2.7 DIN96

Note

The meter is mounted on switchgear boards (metal cabinet) in electrical facilities.

Page is loading ...

ROOTECH Accura 3300S User guide

ROOTECH Accura 3300S User guide

Related papers

Other documents