EnGenius EGS2108P User manual

User Manual

Business Solutions

EGS Smart Switch Series

8-Port Gigabit Switches

EGS2108P | EGS2110P | EGS5110P

version 1.0

2

IMPORTANT

To install your Switch please refer to the

Quick Installation Guide included in the product packaging.

3

Chapter 1 Product Overview ........................................... 4

Introduction/Package Contents ......................................... 5

 Technical Specications ........................................................  6

Physical Interface ..................................................................... 7

Management Interface ........................................................... 9

Connecting the Switch to a Network .............................. 10

Web Access .................................................................................. 12

Chapter 2 Management ..................................................... 13

System ............................................................................................ 14

- IP Setting .................................................................................. 15

 - Port Settings ............................................................................ 16

- PoE Management ................................................................... 17

 - PoE Port Conguration ....................................................... 18

- Cable Diagnostics/Password .............................................. 20

 -ZeroConguration..................................................................21

L2 Feature .................................................................................... 22

- Port Trunking ........................................................................... 22

- IGMP Snooping/Multicast Group List ....................... 23

- Port Mirroring .......................................................................... 24

- Loopback Detection .............................................................. 25

 - Static MAC Address/Dynamic Address List ........ 26

VLAN ................................................................................................ 27

 - 802.1Q ........................................................................................ 27

- PVID .............................................................................................. 29

- Port-based VLAN ................................................................... 30

 QoS ................................................................................................... 32

 - 802.1p Default Priority ..................................................... 32

- CoS Priority Class .................................................................. 33

- Storm Control ........................................................................... 34

- Bandwidth Control ................................................................. 35

Chapter 3 Maintenance....................................................... 36

Maintenance ................................................................................ 37

 Upgrading/Resetting .......................................................... 38

Rebooting/Logging Out ..................................................... 39

Appendix ............................................................................... 40

FCC Interference Statement ................................................ 41

IC Interference Statement .................................................... 42

CE Interference Statement .................................................. 44

Table of Contents

4

Chapter 1

Product Overview

5

Maximum data rates are based on IEEE 802.3ab standards. Actual throughput and range may vary depending on distance between devices or trac and bandwidth load in the network.

Features and specications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

The EGS Smart Switch Series are smart switch devices

specially designed to support Access Points and IP

Surveillance cameras, VOIP phones, and other PoE-Capable

. devices as well as other Ethernet-based networking

equipments or computers.The Smart Switch Series provide

simple, yet powerful PoE manageability with features

such as: IEEE 802.3af or IEEE 802.3at/af ports, PoE port

management, loopback detection, and IGMP snooping.

Package Contents

Your EGS Smart Switch package will contain the following

items*

• EnGenius Switch

• QuickInstallationGuide

• PowerAdapter(EGS2108P&EGS2110P)

• WallMountKit(EGS2108P&EGS2110P)

• GroundScrewKit(EGS2108P&EGS2110P)

Introduction

• PowerCord(EGS5110POnly)

• RackMountKit(EGS5110POnly)

*(allitemsmustbeinpackagetoissuearefund):

6

Environment & Mechanical:

Temperature Range

Operating: 32 to 104°F / 0 to 40°C

 Storage:-40to158°F/-40to70°C

Humidity(non-condensing):5%-95%

L2 Features:

Loopback Detection

IGMP Snooping v1/v2

Port Trunking

Port Mirroring: One to one and many to one

Static MAC Address

Dynamic MAC List

Bandwidth Control

802.1QVLAN

Port-based VLAN

Storm Control

BootP/DHCP Client

Firmware Burn-Proof

Cable Diagnostic

CoS

PoE Management

Power on/off per port

 PowerClassConguration

Power feeding with priority

 User-denedpowerlimit

Standard:

Switching Capacity:

 20Gbps(EGS5110PandEGS2110P)

 16Gbps(EGS2108P)

Max.ForwardingRate(64kBytes):14.88Mpps

Forwarding Mode: Store and Forward

Packet Buffer Memory: 512K Bytes

Flash Memory: 4 MB

Port Functions:

810/100/1000MbpsPortsinthefrontpanel

21000MbpsSFPSlot(EGS5110PandEGS2110P)

PoE Capability:

PoEStandard:Port1~8SupportIEEE802.3at/af(EGS5110P)

PoE Capable Ports:

 Port1~8canoutputupto30W(EGS5110P)

 Port1~8canoutputupto15.4W(EGS2110P)

 Ports:Port1~4canoutputupto15.4W(EGS2108P)

PoE budget:

 130Watts(EGS5110P)

 61.6Watts(EGS2108PandEGS2110P)

LED Indicator

Device:

Power LED x1

Fault LED x1

PoE Max LED x1

LAN Mode LED x1

PoE Mode LED x1

SFPPorts:(EGS5110PandEGS2110P)

LAN/PoE Mode

Link/Act

Technical Specications

7

Physical Interface

Dimensions and Weights

Desktop Design: EGS2108P & EGS2110P

Weight: 1.39 lb.

Width:9.45” Length:4.13” Height:1.06”

Dimensions and Weights

Rack Mountable Design: EGS5110P

Weight: 4.45 lb.

Width: 12.99” Length: 9.05” Height: 1.7”

EGS2108P - Front EGS5110P - Front

EGS2110P - Front

EGS 2108P/EGS2110P - Back

EGS5110P - Back

1

3

4

7 7

7

12

13

6 6

6

5 5

5

2

1

3

2

8

11

9 9

9

8 10 10

10

8

8 RJ-45 LAN Ports: 10/100/1000 Mbps RJ-45 LAN ports.

9 LAN Mode LED (Per Copper Port): Light off = No link is

established on the port; Solid Amber Light = A valid 10/100 Mpbs

link is established on the port; Solid Green Light = A valid 1000

Mbps link is established on the port.

10 Link/Act LED (Per Copper Port): Light off = No link is established

on the port; Solid Light = A valid link is established on the port;

Blinking Light = Packet transmission on the port.

11 SFP Ports: Small form factor pluggable ports.

12 Power Connector

13 Power Switch

1 Power LED: Light off = Power off; Solid Light = Power On.

2 Fault LED: Light off = Normal Behavior; Solid Light = Error.

3 PoE Max LED: Light off = Additional PoE device may still be added;

Solid Light = The PoE device’s output power has exceeded total

PoE limit. No additional devices can be powered on via PoE.

4 LAN Mode LED: Light off = LAN mode is not activated; Solid Light

= LAN mode is activated.

5 PoE Mode LED: Light off = PoE mode is not activated; Solid Light

= PoE mode is activated.

6 LED Mode Selector: Press to change between LAN and PoE mode.

7 Reset Button: Press to reset the device to factory default settings.

9

Each EnGenius Gigabit PoE or PoE+ Smart Switch features an embedded web interface for the monitoring and

management of your device.

Management Interface

10

Connecting the Switch to a Network

Discovery in a Network with a DHCP Server

Use this procedure to setup the Switch within a network

that uses DHCP.

1. ConnectthesuppliedPowerAdapter(cord)totheSwitch

and plug the other end into an electrical outlet. Turn the

Power Switch on the back of the device to the ON

  Position (for EGS2108P and EGS2110P). Verify the

Power LED indicator is lit on the Switch.

2. Wait for the Switch to complete boot up. It might take

a minute for the Switch to complete boot up.

3. ConnectoneendofaCategory5/6Ethernetcableinto

  theGigabit(10/100/1000)Ethernetportontheswitch

front panel and the other end to Ethernet port on the

computer. Verify that the LED on Ethernet ports of the

switch are green.

4. Once your computer is on, ensure that your TCP/IP is set

to On or Enabled. Open Network Connections and then

click Local Area Connecton. Select Internet Protocol

Version 4 (TCP/IPv4). If your computer is already on a

network, ensure that you have set it to a Static IP Address

  ontheInterface(Example:192.168.0.10andtheSubnet

  Maskaddressas255.255.255.0).

5. Open a web browser on your computer. In the address

 barofthewebbrowser,enter192.168.0.239andclick

Enter.

6. A login screen will appear. By default, the password is

password. Enter the current password of the Switch

and then click Login.

7. Once logged in, click IP Setting under and select DHCP.

8. Click Apply to save the settings.

9. ConnecttheSwitchtoyournetwork(DHCPenabled).

10.OntheDHCPserver,ndandwritedowntheIPaddress

allocated to the device. Use this IP address to access

the management interface.

11

Discovery on a Network without a DHCP Server

This section describes how to set up an EnGenius Gigabit

PoE or PoE+ Smart Switch in a network without a DHCP

server. If your network has no DHCP service, you must

assign a static IP address to your Switch in order to log in

to the web-based switch management.

1. Connect the supplied Power Adapter (cord) to the

Switch and plug the other end into an electrical outlet.

Turn the Power Switch on the back of the device to

the ONPosition(forEGS2108PandEGS2110P).Verify

the Power LED indicator is lit on the Switch.

2. Wait for the Switch to complete boot up. It might take

a minute or so for the Switch to complete boot up.

3. ConnectoneendofaCategory5/6Ethernetcableinto

  theGigabit(10/100/1000)EthernetportontheSwitch

front panel and the other end to Ethernet port on the

computer. Verify that the LED on Ethernet ports of the

Switch are green.

If your Computer is already on a network, ensure that

you have set it to a Static IP Address on the interface

(Example:192.168.0.10andtheSubnetMaskaddressas

255.255.255.0.).

4. Once your computer is on, ensure that your TCP/IP is set

to On or Enabled. Open Network Connections and then

click Local Area Connecton. Select Internet Protocol

  Version4(TCP/IPv4).

5. If your computer is already on a network, ensure that

you have set it to a Static IP Address on the Interface

  (Example:192.168.0.10andtheSubnetMaskaddress

  as255.255.255.0).

6. Open a web browser on your computer. In the address

  barofthewebbrowser,enter192.168.0.239andclick

Enter.

7. A login screen will appear. By default, the password is

password. Enter the current password of the Switch

and then click Login.

8. Once logged in, click IP Setting under the System

Setting and select Static IPtoconguretheIPsettings

of the management interface.

9. Enter the IP address, Subnet Mask and Gateway

10. Click Apply to update the system.

12

Use this procedure to access the management interface

throughaWebbrowserfordeviceconguration.

1. Open a Web browser on your computer and enter

thefollowingaddress(default):http://192.168.0.239.

2. On the login screen, use the following information:

Password: password

To make access to the web-based management interface

more secure, it’s highly reccomended that you change the

password to something more unique.

Web Access

13

Chapter 2

Management

14

The navigation pane at the left of the web browser interface

contains a System tab that enables you to manage your

EnGenius Smart Switch with features under the following

main menu options:

• “Summary”

• “IP Setting”

• “Port Setting”

• “PoE Management”

• “Cable Diagnostics”

• “Password”

• “ZeroConguration”

The description that follows in this chapter describes

conguringandmanagingsystemsettingsintheEnGenius

Smart Switch.

Summary

The Summary screen contains general device information

including the device name, Firmware version, MAC address,

IP address, Gateway, and System Up Time.

Device Name: Shows the model name of the Switch

FW version:ShowstheinstalledrmwareversionoftheSwitch

Serial Number: Shows the serial number of the Switch

Base MAC address: Shows the MAC address of the device

IP address: Shows the IP address assigned by DHCP server.

Gateway: Shows the Gateway of IP interface.

System up Time: Shows the amount of time since the most

recent device reset. The System Time is displayed in the

following format: days, hours, and minutes. For example,

thedisplaywillread:3days,6hours,10minutes.

System

15

IP Setting

The IP Setting screen contains elds for assigning IP

addresses.IPaddressesareeitherdenedasstaticorare

retrieved using the Dynamic Host Conguration Protocol

(DHCP).TheDHCPassignsdynamicIPaddressestodevices

on a network. DHCP ensures that network devices can

have a different IP address every time the device connects

to the network.

NotethefollowingwhenconguringIPAddresses:

If the device fails to retrieve an IP address through

DHCP,thedefaultIPaddressis192.168.0.239.

To access the page, click IP Setting under the system menu.

Dynamic IP Address (DHCP): Enable the IP address to be

congured automatically by the DHCP server. Selecting this

elddisablestheIPAddress,Subnetmask,andGatewayelds.

Static IP Address: Species that the IP address, Subnet

mask,anddefaultGatewaymustbemanuallycongured.

IP Address: Enter the static IP address used to manage the

Switch.

Subnet Mask: Enter the IP address mask.

Gateway:UsethistoconguretheIPaddressofarouter

on the same subnet as the management interface that

connects to other subnets.

Apply: Click APPLY to update the System Settings.

16

Port Settings

Use the Port Setting to congure the speed and duplex

settings of each port.

To access the page, click Port Setting under the system menu.

Port: Shows the port number.

Trunk: Port trunking allows you to assign physical links to

one logical link (trunk) that functions as a single, higher-

speed link providing dramatically increased bandwidth.

Shows which trunk the port belongs to.

Link: Indicates whether the link is up or down at the physical

layer.

Speed: Use the drop down menu to select the port’s speed

and duplex mode. If you select Auto, the duplex mode

and speed will be set by the auto-negotiation. The port’s

maximumcapability(fullduplexand1Gbps)andthefactory

default is Auto.

Apply: Click APPLY to update the System Settings.

17

PoE Management

The PoE Management screen contains system PoE

information for monitoring the current power usage and

assign the total amount of power the Switch can provide

to all of its PoE ports. Ports 1~8 on the EGS5110P are

IEEE802.3at/af compliant ports. Each port is capable of

delivering up to 30W and a total PoE budget of 130W

for uninterrupted PoE use.To access the page, click PoE

Management under system menu.

Total Power Budget: Enter the amount of power the

Switch can provide to all ports.

Current Power Used: Shows the total amount of power

currently being delivered to all ports.

Apply: Click APPLY to apply the new settings to the system.

18

PoE Port Conguration

The PoE Port Conguration screen contains system PoE

informationforenablingPoEonthedeviceandcongure

per port PoE settings.

To access the page, click PoE Port Conguration under

system menu.

Port: Shows the specic port for which PoE parameters

aredened.PoEparametersareassignedtothepowered

device that is connected to the selected port.

Priority: Select the port priority if the power supply is low.

Theelddefaultislow.Forexample,ifthepowersupplyis

runningat99%usage,andport1isprioritizedashigh,but

port6isprioritizedaslow,port1isprioritizedtoreceive

powerandport6maybedeniedpower.Thepossibleeld

values are: 4

• Low – Set the PoE priority level as low.

• Medium – Set the PoE priority level as medium.

• High – Set the PoE priority level as high.

• Critical – Set the PoE priority level as Critical.

Class(Auto):Showstheclassicationofthepowereddevice.

Theclassdenesthemaximumpowerthatcanbeprovided

tothepowereddevice.Thepossibleeldvaluesare:

• Class 0 – The maximum power level at the Power Sourcing

Equipment is 15.4 Watts.

• Class 1 – The maximum power level at the Power Sourcing

Equipment is 4.0 Watts.

• Class 2 – The maximum power level at the Power Sourcing

Equipment is 7.0 Watts.

• Class 3 – The maximum power level at the Power Sourcing

Equipment is 15.4 Watts.

• Class 4 – The maximum power level at the Power Sourcing

Equipment is 30 Watts.

Select this option to base the power limit on the detected

class value. When this value is selected, the user-

conguredvalueconguredinthePowerLimiteldis

ignored.

Class(User dened): Select this option to base the power

limitonthevalueconguredintheUserPowerLimiteld.

19

User Power Limit: Set the maximum amount of power that

can be delivered by a port.

Note: The User Power Limit can only be implemented

whentheClassvalueissettoUser-Dened.

State:

• Enable – Enable the Device Discovery protocol and provides

power to the device using the PoE module. The Device Discovery

Protocol enables the device to discover Powered Devices attached to

thedeviceinterfacesandtolearntheirclassication.

• Disable – Disables the Device Discovery protocol and stops the

power supply to the device using the PoE module.

Status: Shows the port’s PoE status. The possible eld

values are:

• Delivering Power – The device is enabled to deliver power

via the port.

• Disabled – The device is disabled for delivering power via the port.

• Test Fail – The powered device test has failed. For example, a

port could not be enabled and cannot be used to deliver power to

the powered device.

• Testing – The powered device is being tested. For example, a

   powereddeviceistestedtoconrmitisreceivingpowerfromthe

power supply.

• Searching –The device is currently searching for a powered

device. Searching is the default PoE operational status.

• Fault – The device has detected a fault on the powered device

when the port is forced on. For example, the power supply

voltage is out of range, or there is a communication error with PoE

devices, a short occurs, or an unknown error occurs.

Apply: Click APPLY to update the system settings.

20

Cable Diagnostics

The Cable Diagnostics setting provides information about

where connectivity may have failed on the Ethernet

cable. The tests use Time Domain Reectometry (TDR)

technology to test the quality of the Ethernet cable for any

disconnection or failure points.

To access the page, click Cable Diagnostics under system

menu

Port: Select the port to which the cable is connected.

Status: Shows the state of the cable.

Cable Length: Shows the approximate cable length.

Test: Click Test to perform the cable tests for the selected

port.

Password

Click Password from the System section. The password

screen appears. You can set a new password. You must

entertheoldandnewpasswordsandconrmthenewone.

Click Apply to enable the new password.

To access the page, click Password under system menu.

Password: Enter your password; the default password is

password.

New Password: Set the new password for the Switch

Conrm:Enterthenewpasswordagain

Apply: Click APPLY to update the system settings.

Page is loading ...

EnGenius EGS2108P User manual

This manual is also suitable for

EnGenius EGS2108P User manual

Related papers

Other documents