Elvox ART. 89F4/T Operating instructions

Brand: Elvox

Model: ART. 89F4/T

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

ART. 89F4/T (alphanumeric audio entrance panel)

ART. 89F7/CT (alphanumeric colour video entrance panel)

ART. 805N/T (additional entrance panel)

Audio and video elvox 2-Wire system with entrance panels

series Patavium keypad and numerical display

Installation and operation manual

ART. 89F4/T

ART. 89F4/CT

ART. 805N/T

INTRODUCTION

The PATAVIUM serie TWO WIRE ELVOX electronic entrance pa-

nels consist of the following parts:

- 1 brass plate with gold-plating and varnishing using the tita-

nium nitride PVD technique.

- 1 flush-mounted back box in zinc plated plate.

- 1 electronic unit with microcontroller.

The following entrance panel models to be configured:

- Audio entrance panel with electronic agenda, alphanumeric

keypad and display, with standard modules type 89F4/T...

- Video entrance panel with colour camera, electronic agenda,

alphanumeric keypad and display, with standard modules type

89F7/CT.

All entrance panels are supplied with the “Engaged-Please Wait”

message, while entrance panels with display have an alphanu-

meric display with 2 lines x 16 characters and an electronic name

index for up to 400 users. Each user can be associated with two

names comprising max. 16 characters.

An external CCTV type camera can be connected to an audio

entrance panel 89F4 or 89F3, after re-configurating the panel as

video as described in paragraph “Hardware programming – En-

trance panel programming modification”.

The entrance panel can be programmed with the entrance panel

keypad or with programming module Type 950C or the PC Soft-

ware SaveProg Type 69CD, in this case it is necessary to have

the interfaces Type 692I or Type 692I/U.

BASIC ENTRANCE PANELS

The basic entrance panels consist of: 1 electronic unit, 1 con-

necting terminal block and 1 PATAVIUM series brass entrance

panel. The electronic unit is equipped with: 1 speech unit, 1 ca-

mera for the video versions, 1 back-lit alphanumeric display, 1

keypad and 1 cabling for the terminal block connection. The

standard modules for video panels in B/W are equipped with a

b/w camera with ¼" CCD sensor and fixed 3 mm lens and LED

for infrared lighting. The standard modules for video panels in

colour are equipped with a b/w camera with ¼" CCD sensor and

fixed 3 mm lens and white indicator LED. All panels with came-

ras can be tilted manually, horizontally or vertically, on removal of

the plate. Example of standard module with camera.

1 2 3

4 5 6

7 8 9

ABC DEF

GHI JKL MNO

PQRS TUV WXYZ

Fig. 1

Fig. 2

Controls:

2 – Reset

3 - Balance

Wiring for terminal block con-

nection

Manual horizontal and vertical tilt

Electronic unit

Plate series PATAVIUM

EXT+

EXT-

VLED

S+

S-

+12V

-L

EXT+

EXT-

VLED

S+

S-

+12V

-L

CN2

CN1

CS2411 250105

Terminal block

CN1) Connector for electronic unit.

CN2) Connector for programmer Type 950C.

B2) 2-wire Bus (cable riser).

B1) 2-wire Bus (cable riser).

EXT+) External power supply (+ type 6923).

EXT-) External power supply (- type 6923).

VLED) LED power supply for additional modules.

X) Video input (coaxial core), for external ca-

mera (for type 89F8 only).

M) Video input (coaxial sheath), for external

camera (for type 89F8 only).

PA) Input for door open sensor (with reference

to terminal M).

CA) Door open command (with reference to

terminal M).

M) Ground.

S+) 12Vdc lock output (+).

S-) 12Vdc lock output (-).

+12V) +12V output (max 100 mA) with PTC pro-

tection.

-L) External camera pilot, open collector out-

put.

SR) Lock pilot via relay, open collector output.

F2) F2 function pilot via relay, open collector

output.

F1) F1 function pilot via relay, open collector

output.

M) Ground.

)

The panel supplies a current peak IT> 1A for 10

mS, followed by a hold current I

= 200mA for

the entire duration of the lock command (see

lock time).

Fig. 4

Fig. A

Fig. B

Fig. C

Points to be chosen for the cable to get through. To remove

with a screwdriver.

To reach the name-tags operate on the additional panel rear side

as indicated in figure.

ART. 805N/T

Fig. 3

ADDITIONAL ENTRANCE PANELS

It possible to place side by side of the electronic basic entrance

panels one or more additional entrance panels and precisely type

805N/T for the basic entrance panels type 89F4/T, 89F7/T,

89F7/CT.

INSTALLATION OF THE ENTRANCE PANEL

The installation of the basic entrance panel requires the use of

the flush-mounted back box placed inside the package.

Installation

- Install the back boxes at approx. 1,65 m high from the back

box upper side to the soil (Fig. 4).

- Fit the back box inside the wall making the tubes for the cable

pass through the holes, see sequence Fig. A, Fig. B, Fig. C.

- If the installation requires the coupling of more back boxes,

use the proper separator brackets to fix the boxes among

them (Fig. 5).

- Connect the terminal block of the electronic unit to the termi-

nal block by means of the cabling present on the upper side

(Fig. 6).

- Insert the microphone in proper seat placed on the rear side of

the brass entrance panel (Fig. 7).

- Close the entrance panel paying attention that the electronic of

same adheres perfectly to the brass plate allowing the push-

buttons to be activated until the run end. Should this not be

possible, adjust the screw inside the flush-mounted back box,

thus allowing the electronic unit to adhere to the brass plate

(Fig. 8).

- Close the entrance panel by using the proper door lock blocks

(Fig. 9)

- Carry out the programming phases.

Fig. 7

Fig. 8

Fig. 9

Fig. 5

Fig. 6

PRELIMINARY OPERATIONS

The entrance panel is supplied already with a standard configuration, to be

modified in the case of multiple entrance panels in the same system and

if the user wishes to change the entrance panel operating parameters.

There are three possible types of programming:

- Programming of the parameters listed below, so as to configure the en-

trance panel according to system requirements.

- Hardware programming, which changes the standard specifications of

the entrance panel and should only be done for special situations.

- Sequential encoding, for programming the identification code of the in-

terphones/monitor interphones via the entrance panel.

The entrance panel can be programmed with the entrance panel keypad

or with programming module Type 950C or the PC Software SaveProg

Type 69CD, in this case it is necessary to have the interfaces Type 692I

or Type 692I/U.

Parameters for programming:

- Parameter Default value

- Message language English

- Entrance panel ID

- Type code Sequential

- Lock code R+1

- Push-button preferential code No association

- Lock passwords No association

- Device numbering No association

- Search the entire agenda No

- Device names No association

- Programming password 654321

- Reply time 30 sec.

- Conversation time 120 sec.

- Self-start time 10 sec.

- Lock time 1 sec.

- F1 time 1 sec.

- F2 time 1 sec.

- External volume 15

- Internal volume 3

- Lock block Disabled

- Entrance panel ringtone repetition Enabled

- Monitor/interphone ringtone cycles 2

- Common locks No association

- Common F1 No association

- Common F2 No association

- Self-start disable No

Self-start sequence (Master entrance panel only)

No association

- Clock 01/01/05 00:00

- Timed code enable No

- First timed code No association

- Last timed code No association

- Code validity time bands No association

- Audio/video door entry unit configuration

- Flag YES / NO

- Function key assignment

o Not Assigned

oIntercommunicating

o Self-Starting

o Auxiliary

o F1 function

o F2 function

o F1 function specific

o F2 function specific

o No Internal Call Ringtone

o No External Call Ringtone

- Call groups (4)

- Associated door call units (4)

- Volume or loudness for 6600 series appliances and derivatives

o Ringtone

o Speakerphone

o External ringtone type

o Brightness (only video door entry units)

o Contrast (only video door entry units)

o Door call ringtone type models Vimar®)

o Intercommunicating ringtone type (only for some models

Vimar®)

- Remote button module configuration.

The essential programming operations, which must be carried out before

any others, are:

- Slave entrance panel assignment. On systems with a single entrance

panel, the entrance panel will be defined as Master. In systems with se-

veral entrance panels, regardless of type (alphanumeric, push-buttons),

one will be defined as MASTER and the others as SLAVE.

- Entrance panel ID, entrance panel identification code. In systems with

several entrance panels, the SLAVE entrance panels (alphanumeric,

push-buttons, landing) will be identified with a different code for each.

PARAMETER PROGRAMMING

(Make the modifications by connecting one entrance panel at a time)

In systems with several entrance panels, it is necessary to distinguish one

MASTER entrance panel (one only) and the others as SLAVE entrance pa-

nels, regardless of type (alphanumeric, push-buttons, landing). All entrance

panels are supplied already set up as MASTER entrance panels.

Alphanumeric entrance panels are set up as MASTER or SLAVE by the soft-

ware programming of the identification code of the entrance panel. Until

the identification codes of all entrance panels have been assigned, it is ad-

visable to programme the entrance panels by connecting them to the sy-

stem one at a time.

Connect the entrance panel defined as MASTER last.

Procedure for accessing parameter programming mode

- Power up the entrance panel or, if applicable, press the “RESET-2” push-

button (next to the loudspeaker).

- When switched on or reset, the entrance panel (only if defined as MA-

STER) queries the system as it searches for other entrance panels, and

displays the message:

- Wait for the entrance panel to return to the rest state and display the

messages:

- Press the and push-buttons simultaneously (if applicable, first press

and then ).

- Release the push-buttons.

- When the following messages are displayed alternately

key in the password, which is by default

- Each time you press a button a short “beep” is emitted, an asterisk “*”

appears on the display and you have a further 25 seconds (timeout) to

press the next push-button. If this time limit is exceeded, the entrance

panel exits programming mode

- After keying in the password press the push-button . If the pas-

sword is incorrect, the entrance panel returns to the rest state and exits

the procedure, otherwise, it goes into parameter programming mode

and displays the following message:

Parameter programming procedure

Once in programming mode, use the and push-buttons to

move between parameters, the push-button to confirm changes, and

the push-button to cancel changes. The 1st line of the display nor-

mally shows the current parameter and the 2nd line shows the value assi-

gned to it. During programming, no more than about 30 seconds (timeout)

must elapse between one press of a push-button and the next. If this time

limit is exceeded, the entrance panel exits programming mode.

GHI

ABC

DEF

GHI

JKL

MNO

SEQUENCE

1.1

MESSAGE LANGUAGE

1.2

ENTRANCE PANEL ID

1.3

NUMBER OF CODING DIGITS

2.3

PROGRAMMING

PASSWORD

2.4

ANSWER TIME

2.5

CONVERSATION TIME

2.6

SELF-START TIME

2.9

FUNCTION 2 TIME

3.0

EXTERNAL VOLUME

3.1

INTERNAL VOLUME

3.2

LOCK BLOCK

1.4

LOCK CODE

o x 200

2.8

FUNCTION 1 TIME

1.8

KEY F1

o x 200

1.9

KEY F2

o x 200

3.3

ENABLINGS/DISABLINGS

2.7

LOCK TIME

2.1

SEARCH THE ENTIRE AGENDA

o x 200

3.4

ENTRANCE PANEL RINGTONE

REPETITION

o x 200

2.2

DEVICE NAMES

1.5 PREFERENTIAL

CODE

1.6 PREFERENTIAL

CODE

1.7

LOCK PASSWORDS

2.0 DEVICE NUMBERING

(only if NUMBER OF CODING

DIGITS differs from

SEQUENTIAL CODE)

4.0 SELF-START

SEQUENCE

(FOR MASTER ENTRANCE

PANEL ONLY)

4.7

CHANGING INTERPHONES/

MONITORS INTERPHONES

CONFIGURATION

SEQUENCE

o x 200

4.4

FIRST TIMED CODE

4.5

LAST TIMED CODE

4.6

CODE VALIDITY TIME BANDS

4.3

TIMED CODE ENABLE

4.2

CLOCK

o x 4

- 1.1 MESSAGE LANGUAGE

Indicates the message display mode, in Italian or English.

Default value = English.

When the following message is displayed in the 1st line:

Press 1 for “ITALIAN” and 2 for “ENGLISH” (or other language depending

on the software version).

Press to confirm the change or to cancel. When you confirm

the change, the message “Fatto!” or “Done!” will appear, depending on

the language selected.

- 1.2 ENTRANCE PANEL ID

Identify the entrance panel with a code from 1 to 15. If the value is 1, the

entrance panel is set as MASTER; from 2 to 15, it is set as SLAVE.

Default value = 1.

When the following message is displayed in the 1st line:

Key in the identification code with push-buttons to .

Press to confirm the change or to cancel. When you confirm

the change, the entrance panel checks the availability of the code. If there

is already another entrance panel in the system connected with the same

code, the message “Panel ID .. already in use” appears, and it is neces-

sary to enter a different code. If the code is greater than 15, the message

“Over limit” appears. If it is correct, the message “Done!” appears.

It is possible to use 0 for temporarily “unprogramming” the entrance

panel.

- 1.3 NUMBER OF ENCODING DIGITS

Sets the type of encoding for calls to interphones and moni-

tors/interphones.

The modes are as follows:

- Sequential encoding: the interphones/monitors interphones are numbe-

red with codes from 1 to 200 (physical encoding for entrance panels

with push-buttons). In this case, keying in 0 before the other digits is

optional, e.g. the codes 001, 01 and 1 are effectively the same.

- 4-digit encoding, the audio/video door entry units are numbered from

1 to 9999. In the following case the codes can have from 1 to 4 digits.

This parameter activates parameter 2.0 DEVICE NUMBERING.

- 8-digit encoding, the audio/video door entry units are numbered from

1 to 99999999. In the following case the codes can have from 1 to 8 di-

gits. This parameter activates parameter 2.0 DEVICE NUMBERING.

Default value = sequential encoding.

Note: In case of numbering with 4 or 8 digits, the 0s on the left are sig-

nificant. For example 14, 014, 0014 are three separate numbers.

When the following message is displayed in the 1st line:

Press push-buttons 1, 2 or 3 for sequential, 4-digit or 8-digit encoding re-

spectively.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 1.4 LOCK CODE

Sets the necessary push-buttons for activating the door lock release fun-

ction directly from the entrance panel. On pressing the push-buttons it is

then necessary to key in one of the 200 8-digit codes recorded in parame-

ter 1.7 LOCK PASSWORDS.

The modes are as follows:

- Push-button : this type of dialling can be inconvenient if the call

codes require 0 as the first digit.

- Push-buttons + ,, pressed simultaneously.

- Push-button , with entrance panel in rest state.

Default value = + .

WXYZ

3.5

NUMBER OF RINGTONE CY-

CLES

3.6

COMMON LOCKS

3.7

COMMON F1

3.8

COMMON F2

o x 4

3.9

SELF-START DISABLE

4.8

REMOTE BUTTON MODULE

CONFIGURATION

Default value = + .

When the following message is displayed in the 1st line:

Press push-buttons 1, 2 or 3 for , + , respectively.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 1.5 PREFERENTIAL CODE

Assigns to the push-button a call code to an interphone or monitor inter-

phone. Without pressing other push-buttons, it is possible to call a given

device by pressing the push-button .

The type of call code depends on the value set in parameter 1.3 NUM-

BER OF ENCODING DIGITS(3, 4 or 8 digits).

Default setting = (empty).

When the following message is displayed in the 1st line:

Key in all digits of the call code with push-buttons al . Use the

push-button to cancel the last digit entered.

Press to confirm the change or to cancel. To change the value

previously set, press the push-button before the numeric digits, and

use the digits and the push-button to change the value. When you

confirm the change, the message “Done!” will appear. If parameter 1.3

NUMBER OF ENCODING DIGITS is set as sequential, the entrance panel

checks that the value entered does not exceed 204; if it does, the message

“Over limit” appears.

- 1.6 PREFERENTIAL CODE

Assigns to the push-button a call code to an interphone or monitor inter-

phone. Without pressing other push-buttons, it is possible to call a given

device by pressing the push-button .

The type of call code depends on the value set in parameter 1.3 NUM-

BER OF ENCODING DIGITS(3, 4 or 8 digits).

Default setting = 000, 0000 or 00000000 (parameter disabled).

Enter the call code complete with all the digits by using the push-buttons

from to . Use the push-button to cancel the latest digit

entered.

Press the push-button to confirm the modification or the push-but-

ton to cancel. If you press before the push-button before the

numerical digits, the already recorded number gets changed; to modify

the value use the digits and the push-button . On confirmation of the

modification, the message “Done” is displayed. If the parameter 1,3 “Num-

ber of coding digits” gets entered as sequential, the panel verifies that the

entered value does not exceed 204; if it does exceed this value, this is in-

dicated by the message: “Over limit”.

The numbers from 201 to 204 correspond to porter switchboards.

- 1.7 LOCK PASSWORD

It is possible to record up to 200 different codes made up of 8 digits, to

open the lock directly from the keypad of the entrance panel (see parame-

ter 1.4 LOCK CODE). Default setting = (empty).

When the following message is displayed in the 1st line:

WXYZ

Use the push-buttons to select one of the 200 passwords. If

applicable, key in the password and press to select it.

Next to the desired password, press to access change mode.

Key in the code you want to record (max. 8 digits); if necessary, press

to delete the last digit entered.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 1.8 F1 CODES

It is possible to record up to 200 different max. 8-digit codes for control-

ling F1 directly from the entrance panel keypad.

Default setting = (empty).

When the following message is displayed in the 1st line:

Use the push-buttons to select one of the 200 codes. If appli-

cable, key in the code and press to select it. Next to the desired

code, press to access change mode.

Key in the code you want to record (max. 8 digits); if necessary, press

to delete the last digit entered. Press to confirm the change or

to cancel. When you confirm the change, the message “Done!” will ap-

pear!”.

- 1.9 F2 CODES

It is possible to record up to 200 different max. 8-digit codes to control F2

directly from the entrance panel keypad.

Default setting = (empty).

When the following message is displayed in the 1st line:

Use the push-buttons to select one of the 200 codes. If appli-

cable, key in the code and press to select it. Next to the desired

code, press to access change mode. Key in the code you want to re-

cord (max. 8 digits); if necessary, press to delete the last digit ente-

red. Press to confirm the change or to cancel. When you

confirm the change, the message “Done!” will appear!”.

- 2.0 DEVICE NUMBERING

If parameter 1.3 NUMBER OF ENCODING DIGITS is set to 4 or 8 digits, it

is necessary to assign a 4- or 8-digit call code to each interphone and

video interphone.

The mapping associates the physical code (from 1 to 200) of each inter-

phone and video interphone with the call code.

Default setting = (empty).

When the following message is displayed in the 1st line:

Use the push-buttons to select one of the 200 physical codes

(device ID). If applicable, key in the code and press to select it.

Next to the desired code, press to access change mode.

Key in the complete call code you want to record (up to 4 or 8 digits); if ne-

cessary, press to delete the last digit entered.

Press on confirmation the change or to cancel. When you con-

firm the change, the message “Done!” will appear. If the call code has been

assigned, the entrance panel displays the message “Code ... used by ...”.

To cancel a code, select the physical code in question, press to ac-

cess change mode, enter one and press .

To cancel all the associations, next to any physical code press . When

the message:

appears, press and then to confirm the cancellation, or press

to escape. After confirming the operation, wait for completion of the

cancellation process.

- 2.1SEARCH THE ENTIRE AGENDA

Press the key to move to the next item, which enables configuration

of the panel to scroll through the entire agenda (see paragraph 6.2) by en-

tering an empty name as the search criteria. Normally at least the first let-

ter of the name to be searched should be entered. With the flag selected,

press followed by to see the first name in the list, regardless of

the initial. Use keys and to scroll through the entire agenda.

This function is disabled by default:

To activate the function, press :

followed by :

To deactivate, press e .

- 2.2 DEVICE NAMES

ELVOX TWO WIRE alphanumeric entrance panels are equipped with an

electronic name index for 200 users. Each user can be assigned a pair of

names (a and b) of 16 characters each.

Default value = no association

Note: The porter switchboards, corresponding to numbers 201 - 204,

have a fixed name Switchboard 1.... Switchboard 4.

When the following message is displayed in the 1st line:

Use the push-buttons to select one of the 200 users.

Two lines, a and b, correspond to each user. To select these, use the push-

buttons . If applicable, key in the number of the user and press

to select it.

Next to the desired line, press to access change mode. Once in

change mode, a flashing cursor shows where to enter the character.

To enter characters/symbols, use the push-buttons from to .

WXYZ

BUTTON SYMBOL

ABC

ABC2abcÁÀÃÅÄÆÇÈáàãåäæçè

DEF

DEF3defïÉÈÊÌéèêì

GHI

GHI4ghiÍÌíì

JKL

JKL5jkl

MNO

MNO6mnoÑñÓÒÕÖóòõö

PQRS

PQRS7pqrsRŠršß

TUV

TUV8tuvÚÙÜÙúùüù

WXYZ

WXYZ9wxyzÝZýz

0_$&*#+-=/%"'

Each push-button has more than one character/symbol assigned to it (see

previous table). To reach the desired symbol, press several times before

the timeout of 2 seconds, which is renewed each time you press a key.

If the symbol entered previously was a capital letter, even if you change

push-button, you will re-start with a capital. If it was lower case, you will re-

start in lower case. If it was a digit, you will re-start with a digit.

To enter a character/symbol located on a different push-button from the

one previously pressed, it is not necessary to wait for the end of the time-

out.

While entering symbols, it is possible to use the push-buttons

to move along the line, and the push-button to delete the cha-

racter preceding the cursor.

Press to confirm the change or to cancel.

After confirmation, the entrance panel will check if the name entered is al-

ready in use by another user. If so, the message “..... used by ...” will ap-

pear, and it will be necessary to enter another name. Alternatively, the

message “Done!” will appear. If at least one name has been changed, on

completion, the names will be ordered alphabetically. This process takes

about 10 seconds for a full name index.

Example :

To key in the previous name, press the following push-buttons in succes-

sion: 333 444 555 444 2 555 33 1 333 444 777 33 66 9999 33

- 2.3 PROGRAMMING PASSWORD

Sets the password for access to the phases of keypad programming.

Default value = 654321

When the following message is displayed in the 1st line:

Key in the new password with push-buttons to .

Press to confirm the change or to cancel.

When you confirm the change, the message “Done!” will appear.

The password is not needed when programming with the programming

module Type 950C and software SaveProg.

- 2.4 ANSWER TIME

To be programmed as required. This is the time interval, expressed in se-

conds, that the entrance panel waits after a call has been terminated and

the time that the handset of the interphone/monitor is raised. If the handset

is not raised within this time interval, the entrance panel disables the inter-

phone/monitor. If the handset is raised before this interval elapses, the en-

trance panel starts to count the conversation time.

Default value = 30 s, minimum value 1 s, maximum value 255 s.

WXYZ

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to .

Press to confirm the change or to cancel. If the value is over

255, the message “Over limit” appears, whereas if the value is correct, the

message “Done!” appears.

- 2.5 CONVERSATION TIME

To be programmed at the user's discretion. This is the time interval, ex-

pressed in seconds, that the entrance panel counts, from the time at which

the handset is raised after the call. The entrance panel disables the exten-

sion after this time interval.Default value = 120 s, minimum value 10 s, ma-

ximum value 2550 s.

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to (in increments of 10

sec.). Press to confirm the change or to cancel. If the value is

over 2550, the message “Out of range” appears, whereas if the value is

correct, the message “Done!” appears.

- 2.6 SELF-START TIME

To be programmed at the user's discretion. This is the time interval, ex-

pressed in seconds, that the entrance panel remains engaged with a mo-

nitor/interphone, from activation by means of the self-start function. The

entrance panel disables the extension after this time interval.

Default value = 10 s, minimum value 1 s, maximum value 255 s.

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to .

Press to confirm the change or to cancel. If the value is over

255, the message “Out of range” appears, whereas if the value is correct,

the message “Done!” appears.

- 2.7 LOCK TIME

To be programmed at the user's discretion. This is the activation time of the

lock connected between terminals S+ / S- and +12V / SR.

Default value = 1 s, minimum value 0 s., maximum value 255 s.

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to .

Press to confirm the change or to cancel. If the value is over

255, the message “Out of range” appears, whereas if the value is correct,

the message “Done!” appears.

- 2.8 FUNCTION 1 TIME

To be programmed at the user's discretion. This is the activation time of the

device connected between terminals +12V / F1.

Default value = 1 s, minimum value 0.5 s, maximum value 255 s.

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to . For the minimum

value of 0.5 s. enter only.

Press to confirm the change or to cancel. If the value is over

255, the message “Out of range” appears, whereas if the value is correct,

the message “Done!” appears.

WXYZ

- 2.9 FUNCTION 2 TIME

To be programmed at the user's discretion. This is the activation time of the

device connected between terminals +12V / F2. Default value = 1 s, mini-

mum value 0.5 s, maximum value 255 s.

When the following message is displayed in the 1st line:

Key in the new time with push-buttons to . For the minimum

value of 0.5 s. enter only. Press to confirm the change or

to cancel. If the value is over 255, the message “Out of range” appears,

whereas if the value is correct, the message “Done!” appears.

- 3.0 EXTERNAL VOLUME

To be programmed at the user's discretion. This is the volume of the loud-

speaker of the entrance panel, settable on 16 levels.

Default value = 15, minimum value 0, maximum value 15.

When the following message is displayed in the 1st line:

Press to access change volume mode.

Press the push-buttons to increase or reduce the volume.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 3.1 INTERNAL VOLUME

To be programmed at the user's discretion. This is the volume of the en-

trance panel microphone, settable on 4 levels.

Default value = 3, minimum value 0, maximum value 3.

When the following message is displayed in the 1st line:

Press to access change volume mode.

Press the push-buttons to increase or reduce the volume.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 3.2 LOCK BLOCK

To be programmed as required. Activation of the lock block enables con-

trol of the lock only when the panel is in call, conversation or self-start sta-

tus.

Default value = block disabled

When the following message is displayed in the 1st line:

Press to enable the lock block or press to disable it.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

WXYZ

3.3 ENABLING/DISABLING

To be programmed as required. This function enables the user to pro-

gramme, for each device, controls on certain commands received by the

entrance panel. This currently relates to the programming of common locks

F1 and F2.

It is possible to programme one or more entrance panels not to react in re-

sponse to one or more interphones/monitor interphones when the lock or

F1 or F2 functions are activated.

It is also possible to programme the entrance panel in such a way that it

can only be activated by certain interphones/monitor interphones.

In order to minimise the number of programming operations, if the entrance

panel already has at least one programmed common lock, the headings

act as enable signals.

The same applies to function F1 or F2. Since common locks are normally

used in building-complex type layouts, by programming one common lock

and enabling only the users of the respective staircase, fewer program-

ming operations are necessary.

The default setting is no programming. The absence of programming is in-

dicated by the symbol: “__”. To change the identification code of the inter-

phones/monitor interphones, use the and keys. Alternatively,

key in the numbers of the monitor or interphone from 1 to 200:

Press to cancel. Press to confirm.

To change the programming of the selected interphones/monitor interpho-

nes, when the current value is shown, press .

The correlation between programming, abbreviations and keys is as fol-

lows:

PROGRAMMING ABBREVIATION KEY

Lock

Dl 1

F1 F1 2

F2 F2 3

- 3.4 ENTRANCE PANEL RINGTONE REPETITION

To be programmed as required. Enables repetition of the ringtone in the mi-

crophone of the entrance panel from which the call is being made.

Default value = enabled

When the following message is displayed in the 1st line:

Press to enable the ringtone and to disable it.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

- 3.5 NUMBER OF RINGTONE CYCLES

To be programmed at the user's discretion. This is the number of times

that the call is repeated in the monitor/interphone when a call push-button

is pressed. A ringtone cycle lasts for a total of 3 seconds (1 second of rin-

gtone and 2 seconds of pause).

Default value = 2 times, minimum value 1, maximum value 20.

When the following message is displayed in the 1st line:

Key in the number of cycles with the push-buttons to .

Press to confirm the change or to cancel. If the value is over 20,

the message “Out of range” appears, whereas if the value is correct, the

message “Done!” appears.

- 3.6 COMMON LOCKS

To be programmed as required. This parameter enables indirect opening

of the lock, at the same time as the opening of the lock of another entrance

panel, at the command of an interphone/monitor interphone. Indirect ope-

ning can be associated with 4 different entrance panels.

Default value = no association, minimum value 1, maximum value 15.

When the following message is displayed in the 1st line:

Enter a number between 1 and 15, i.e. the ID of an entrance panel (in this

case the first of four possible choices) for controlling whose lock also the

current speech unit must activate its own:

To cancel, press . To confirm, press . Acceptance of the com-

mand, as in all cases, is shown on the first line of the display:

WXYZ

Button Action

Do nothing

Deselect

Se, F1, F2

Deselect

Select

Se, F1, F2

Select

8 Select F2

Confirm with or cancel with .

Pressing one of the keys alternately adds / removes the corresponding fun-

ction. To set F1 only press 2 and 1 (or vice versa):

Press to cancel and press to confirm. Acceptance of the com-

mand, as for all the others, is shown in the first line of the display:

By using the key, you can skip all the intermediate steps and go

straight to the previous heading in the programming menu.

To change the settings of all the audio/video door entry units, the proce-

dure is as follows.

For the ID key in no. 0. The display will show:

By pressing the buttons ... it is possible to choose what to

do, that is whether to engage or release the lock and whether with only

the lock, F1, F2 or all three.

The following table shows the actions.

TUV

If the ID is outside the limit, the first line of the display will signal the incon-

gruity:

To cancel the assignment, enter 0 for the ID.

It is possible to move from one index to another also by using and

.From position 1, press to move to the next item of the programming

menu. Press to move quickly, skipping all the intermediate steps, to the

previous item of the programming menu.

Whereas if you enter numbers from 21 to 36, then the end of the line is not

taken to be an entrance panel but an actuator.

Number 21 corresponds to the 1st relay of the 1st actuator, number 36 to

the second relay of the 8th actuator. On the contrary to the lock, F1 or F2,

the actuators are not subjected to locks as described in paragraph 3.3.

In the display phase the entrance panels are preceded by a letter “P”, the

actuators by an “A”.

- 3.7 COMMON F1

To be programmed as required. This parameter enables indirect activation of

the F1 function, at the same time as activation of the F1 function of another

entrance panel, at the command of an interphone/monitor interphone. Indirect

activation can be associated with 4 different entrance panels.

Default value = no association, minimum value 1, maximum value 15.

When the following message is displayed in the 1st line:

Enter a number between 1 and 15, i.e. the ID of an entrance panel (in this case

the first of four possible choices) for controlling whose F1 also the current

speech unit must activate its own:

To cancel, press . To confirm, press . Acceptance of the command,

as in all cases, is shown on the first line of the display:

If the ID is outside the limit, the first line of the display will signal the incon-

gruity:

To cancel the assignment, enter 0 for the ID.

It is possible to move from one index to another also by using and

.From position 1, press to move to the next item of the programming

menu. Press to move quickly, skipping all the intermediate steps, to the

previous item of the programming menu.

Whereas if you enter numbers from 21 to 36, then the end of the line is not

taken to be an entrance panel but an actuator.

Number 21 corresponds to the 1st relay of the 1st actuator, number 36 to

the second relay of the 8th actuator. On the contrary to the lock, F1 or F2,

the actuators are not subjected to locks as described in paragraph 3.3.

In the display phase the entrance panels are preceded by a letter “P”, the

actuators by an “A”.

- 3.8 COMMON F2

To be programmed as required. This parameter enables indirect activation

of the F2 function, at the same time as activation of the F2 function of ano-

ther entrance panel, at the command of an interphone/monitor interphone.

Indirect activation can be associated with 4 different entrance panels.

Default value = no association, minimum value 1, maximum value 15.

When the following message is displayed in the 1st line:

Enter a number between 1 and 15, i.e. the ID of an entrance panel (in this

case the first of four possible choices) for controlling whose F2 also the

current speech unit must activate its own:

To cancel, press . To confirm, press . Acceptance of the com-

mand, as in all cases, is shown on the first line of the display:

If the ID is outside the limit, the first line of the display will signal the incon-

gruity:

To cancel the assignment, enter 0 for the ID.

It is possible to move from one index to another also by using and

.From position 1, press to move to the next item of the program-

ming menu. Press to move quickly, skipping all the intermediate

steps, to the previous item of the programming menu.

Whereas if you enter numbers from 21 to 36, then the end of the line is not

taken to be an entrance panel but an actuator.

Number 21 corresponds to the 1st relay of the 1st actuator, number 36 to

the second relay of the 8th actuator. On the contrary to the lock, F1 or F2,

the actuators are not subjected to locks as described in paragraph 3.3. In

the display phase the entrance panels are preceded by a letter “P”, the ac-

tuators by an “A”.

- 3.9 SELF-START DISABLE

Press the key to move to the next item, which enables configuration

of the main panel to disable the self-start function on a system level. The

function is enabled by default, and therefore select NO to disable:

To activate the function, press :

followed by :

To deactivate, press and .

- 4.0 SELF-START SEQUENCE

To be programmed at the user's discretion but only on the MASTER en-

trance panel (with ID=1). This parameter allows you to assign to the self-

start push-button of each video interphone (and interphone), the cyclical

start-up of a sequence of entrance panels. Each sequence must consist of

a maximum of 15 entrance panels and contain duplicates of the same en-

trance panel.

Default value = no association.

- 4.2. CLOCK

The clock can be programmed so that the service is performed correctly.

The date and time are stored also when the panel is switched off, for at

least 2 days, by means of a SuperCap capacitor. There are no batteries of

any type. On initial activation of the clock, or when the panel is left swit-

ched off for a prolonged period, the date is set to the 1st January 2005 and

the time at 00:00.

It can be modified via the keypad. Press the key . The modifiable field

is indicated by a rectangle to the right:

To move to the right, use key , and to the left use . Modify the

values by means of the keys to .

On completion confirm by means of . If the values are correct the di-

splay then shows:

If there is an error, for example if the month is set as 88, modifications are

rejected and the rectangle moves to the position of the error:

The weekday does not need to be entered as it is calculated automati-

cally based on the date, by means of the Zeller algorithm.

- 4.3. TIMED CODE ENABLE

The service must be configured and then enabled by means of this para-

meter.

If necessary, though completely configured, this function can be disabled,

to obtain temporary suspension of the service, while all settings remain

enabled for operation. The service is disabled by default.

Press :

followed by to enable the function:

and disable the function.

- 4.4. FIRST TIMED CODE

This parameter specifies the first code to be used for the Timed Code fun-

ction. No code is set by default:

To modify, enter a number from 1 to 200 to by means of the

keys :

To clear settings, enter 0. Confirm by means of :

If the code number is outside the range 0..200, the error message is

shown:

WXYZ

When the following message is displayed in the 1st line:

Use the push-buttons to select one of the 204 physical codes

(device ID) corresponding to an audio/video door entry unit and lastly the

switchboards.

Note: The switchboards 945F at this time do not perform the function of

self-starting.

If applicable, key in the code and press to select it.

Next to the desired code, press to access change mode.

Enter the entrance panel ID code or codes (maximum 15 characters).

To enter the codes, press push-buttons to for entrance panels

1 to 9. For entrance panels 10 to 15, first press and then one of the

push-buttons from to .

When you press , a “?” appears on the display; when you press the

next number, a letter is entered (A->10, B->11, C->12, D->13, E->14, F-

>15).

Use the push-button to cancel the last digit entered.

Press to confirm the change or to cancel. When you confirm

the change, the message “Done!” will appear.

During this phase, it is possible to use the “notepad block” function to

help with the duplication of the codes. While in change mode and without

the ? displayed, press to record the sequence entered.

Exit change mode by pressing or .

Select another device, press to access change mode and then press

to replace the current sequence with the sequence recorded in the

notes. Press to confirm the change or to cancel.

To cancel all the associations, next to any physical code press . When

the message:

appears, press and then to confirm the cancellation, or press

to escape. After confirming the operation, wait for completion of the

cancellation process.

- 4.1 TIMED CODES

For 89F4/7 panels with the clock module, a function can be assigned to

enable a specific number of Lock Codes (paragraph 1.7), F1 codes (para-

graph 1.8), F2 codes (paragraph 1.9) at specific times of the day only.

Two time bands are envisaged for the 24-hour period, each with a resolu-

tion of 30 minutes. This means that the user can specify the time start

and end interval in increments of 30 minutes:

00:00, 00:30, 01:00, 01:30, … 22:30, 23:00, 23:30

For further flexibility, the two time bands can be programmed separately

for weekdays (Monday to Friday) and weekends, or times in which most

situations are not considered fully "work" times (Saturday and Sunday).

For all three types of function (lock, F1 and F2) the set of codes has com-

mon start and and end numbers, but obviously the contents of the three

tables can be programmed differently.

The codes other than the selected set are always active. Only the selec-

ted codes are subject to timed limits. The service can be temporarily di-

sabled by means of a programmed parameter. In this case the specified

codes are never active, while the other remain active.

JKL

WXYZ

If the first code is higher than the second, or if one is programmed and the

other is not, a warning is displayed, requesting the user to check the other

code:

The valid codes are those in which the number ranges from the first and last

as specified, excluding the limits.

- 4.5. LAST TIMED CODE

Similar to the previous code, but referring to the last valid code.

- 4.6. CODE VALIDITY TIME BANDS

As specified above, there are two time bands for days from Monday to Fri-

day and two for Saturday and Sunday. By default there is no setting, and

all start and end values are set at 00:00.

As the end value must be greater than the first value, this programming is

not valid. For example, a start value = 16:00 and end value = 16:00 would

not be valid, or start = 16:00 and end = 10:30.

To modify the time, press :

The double arrow appears on the right to indicate the option to use keys

, and to modify the time in increments of 30 minutes. Alternati-

vely use keys to to set the time:

If necessary use key and to modify the minutes:

Confirm by means of ::

- 4.7 CHANGING MONITOR/INTERPHONE CONFIGURATION

For each audio and video door entry unit installed in the system, it is pos-

sible to configure operating functions grouped in four zones “Flag”, “Pro-

grammable buttons”, “Call groups”, “Door call”. The audio/video door entry

units in the 6600 series have a fifth zone composed of the audio/video lev-

els. To execute this procedure, the devices to be programmed (interphones

and monitors) have to be connected to the system and have to be identi-

fied with a code.

The entrance panel searches for the first device (interphone and monitor),

identified with the physical code 1, and analyses the type of associated

device (6209, 6209+6009, 6309, 6601, etc.).

Use the push-buttons to select one of the 200 devices. If ap-

plicable, key in the code of the device and press to select it.

Next to the desired device, press to access change mode. The con-

figuration options change according to the type of device as indicated in

the following diagrams.

WXYZ

Once in configuration mode, use the push-buttons , and

to move between parameters, the push-button to confirm changes,

and the push-button to cancel changes. The 1st line of the display

shows the current parameter and the 2nd shows the value assigned to it.

CLASS MEANING 6209 (+ 6009) 6309

YES = the monitor switches on when a panel

call is made (except for 6209)

YES = the green led is managed as

door open indicator

YES = the lock pushbutton is used by the device

NO =

the pushbutton is used externally (only for 6309/P, 6309/CP)

YES =

the stair light pushbutton is used by the device

NO =

the pushbutton is used externally (only for 6309/P, 6309/CP)

YES =

the self-start pushbutton is used by the device

NO = the pushbutton is used externally

(only for 6309/P, 6309/CP)

YES = if the F1 / F2 pushbutton is programmed

directly on a specific panel, only panels 1 to 8

can be programmed

NO = only panels 9 to 15

YES = the device is working in porter

switchboard mode

YES =

the device sends the lock command automatically

when a external speech unit/panel calls, if P6 is closed

YES = group G3 functions only for

external calls

YES = group G4 functions only for

internal calls

YES = eliminates the click sound

when a valid key is pressed

YES = does not activate the call repeated output

for intercommunicating calls

YES = group G1 functions only for external calls

YES = group G2 functions only for internal calls

YES = the monitor / interphone does

not ring for intercommunicating calls

YES = the monitor / interphone does

not ring for calls from panels

YES = After the automatic door lock activation

because of the Serr. Aut. flag with P6 close the

interphone or the video interphone cancels the call.

[NO] The possible automatic door lock does not

make the call end (default).

Usually used for a group master.

YES = the call is accepted, and then the

secondary units ring, even if the group master

has ringtone off and therefore does not ring.

NO = if a group master turns off the ringtone

none rings and there is a warning on the

entrance panel.

YES = the device has no timeout for the

intercommunicating conversation. For it to work

properly, both parties talking to each other must

have it on YES.

NO = (Default) and the intercommunicating

conversation lasts at most 5 minutes.

YES = If it is programmed for a head group, this

latter, at the call reception from the push-button

module type 6120, will inform the other members

that it is ringing. If it is programmed for the group

members, they will answer at the call from a type

6120 to their head group ringing. In this way it is

possible to divide the calls between external,

internal and outdoor calls.

NO = No reaction.

FLAG PROGRAMMING

First door call

Fourth door call

DOOR CALL

CLASS MEANING 6209 (+ 6009) 6309

P0 is lock push-button

Functions assigned to pushbuttons.

P1, P2, P3, P7 and P8 as default

(i.e. not programmed) take the

specified value

PROGRAMMABLE KEYS

First call group programming

Fourth and last call

group programming

GROUPS

CLASS MEANING 6601 6611 8879

YES = the monitor switches on when

a panel call is made (not for 6601AU or 6611AU)

YES = the green led is managed

as door open indicator

YES = if the F1 / F2 pushbutton is programmed

directly on a specific panel, only panels 1 to 8 can

be programmed

NO = only panels 9 to 15

YES = the device is working in porter

switchboard mode

YES = group G3 functions only for

external calls

YES = group G4 functions only for

internal calls

YES = eliminates the click sound

when a valid key is pressed

YES = does not activate the call repeater output for

intercommunicating calls

YES = group G1 functions only for

external calls

YES = group G2 functions only for

internal calls

YES = the monitor / interphone dos

not ring for intercommunicating calls

YES = the monitor / interphone

dos not ring for calls from panels

[YES] pressing the door lock push-button ends

the conversation (default value in model /F of monitor)

NO = the door lock push-button operates normally

From version 4 of monitor and entrance panels.

[YES] to activate the audio connection press

the talk/listen push-button. To deactivate the audio

press the push-button again (default value on model

/F of monitor).

NO = To activate the audio connection the talk/listen

push-button must be kept pressed.

From version 4 of monitor and entrance panels.

FLAG PROGRAMMING

Valid only for some Vimar products.

[YES] the square button (self-start) becomes the sec-

ond function regardless of the position of the me-

chanical switch.

NO = has the self-start function.

Valid only for some Vimar products.

[YES] there is home automation.

NO = (Default)

Usually used for a group master.

[YES] the call is accepted, and then the secondary

units ring, even if the group master has ringtone off

and therefore does not ring.

NO = if a group master turns off the ringtone none

rings and there is a warning on the entrance panel.

[YES] the device has no timeout for the intercommu-

nicating conversation. For it to work properly, both

parties talking to each other must have it on YES.

NO = (Default) and the intercommunicating conver-

sation lasts at most 5 minutes.

[YES] After the panel ring tones the monitor answers

automatically. Even the flag “T./L. On/Off:NO²”must

be set to YES.

NO = No automatic answer (default).

[YES] If it is programmed for a head group, this latter,

at the call reception from the push-button module

type 6120, will inform the other members that it is

ringing. If it is programmed for the group members,

they will answer at the call from a type 6120 to their

head group ringing. In this way it is possible to divide

the calls between external, internal and outdoor calls.

NO = No reaction.

First door call

Fourth door call

DOOR CALL

CLASS MEANING 6209 (+ 6009) 6309

P0 is lock push-button

Functions assigned to pushbuttons.

P1, P2, P3, P7 and P8 as default

(i.e. not programmed) take the

specified value

PROGRAMMABLE KEYS

First call group programming

Fourth and last call

group programming

GROUPS

- FLAG PROGRAMMING

Next to the desired FLAG, press 1 for YES and 0 for NO.

Press to confirm the change. When you confirm the change, the

message “Done!” will appear.

FLAG description

Monitor Switch-on -> [YES] The monitor switches on when called by the

entrance panel (default).

[NO] The monitor does not switch on when called,

but can switch on with the self-start function or by

replying.

Green LED -> [YES] The green LED is used to indicate that the

door is open (default).

[NO] The LED remains OFF.

Lock -> [YES] The lock push-button is set to open the door

(default).

[NO] The lock push-button is used as an N.O.

push-button with free contacts, for types 6309/P

and 6309/CP only.

Stair light -> [YES] The stair light push-button is set to activate

the 1st auxiliary function of the 1st relay (default).

[NO] The stair light push-button is used as an N.O.

push-button with free contacts, for types 6309/P

and 6309/CP only.

Self-start -> [YES] The self-start push-button is set for self-start

of the monitor (default).

[NO] The self-start push-button is used as an N.O.

push-button with free contacts, for types 6309/P

and 6309/CP only.

F1/F2 1-8 -> [YES] If a push-button is programmed for direct

F1/F2 to a specific entrance panel, the push-but-

ton can manage F1/F2 of entrance panels 1 to 8

(default).

[NO] If a push-button is programmed for direct

F1/F2 to a specific entrance panel, the push-but-

ton can manage F1/F2 of entrance panels 9 to 15

(default).

Switchboard -> [YES] The device works in a system with switchbo-

ard.

[NO] The device does not work in a system with

switchboard (default).

Auto. Lock ->

[YES] The device sends the door lock release com-

mand on receipt of a call from the entrance panel if

push-button P6 is closed.

[NO] The device does nothing (default).

G3 ext. only -> [YES] The call group G3 is made only for calls from

an entrance panel.

[NO] The call group G3 is made for intercommuni-

cating calls and calls from an entrance panel (de-

fault).

G4 int. only -> [YES] The call group G4 is made only for intercom-

municating calls.

[NO] The call group G4 is made for intercommuni-

cating calls and calls from an entrance panel (de-

fault).

No beep -> [YES] When a push-button is pressed on the inter-

phone/monitor a beep is emitted (default).

[NO] When a push-button is pressed on the inter-

phone/monitor no beep is emitted.

No CALLREP IC -> [

[YES]

Does not activate the call repeater output for

the intercommunicating calls

[NO] Activates the call repeater output for the in-

tercommunicating calls (default).

G1 only ext ->

[YES]

The G1 call group is carried out only for calls

from entrance panel

[NO] The G1 call group is carried out for call from

entrance panel and intercommunicating units (de-

fault).

G2 only ext ->

[YES]

The G2 call group is carried out only for inter-

communicating calls

[NO] The G2 call group is carried out for call from

entrance panel and intercommunicating units (de-

fault).

No int. ring ->

[YES]

Monitor/Interphone does not sound for inter-

communicating calls.

[NO] Monitor/Interphone sounds for intercommuni-

cating calls (default).

No ext. ring -> [

[YES]

Monitor/Interphone does not sound for call

from entrance panel.

[NO] Monitor interphone sounds for call from en-

trance panel (default).

Para 6209

Door lock Terminates->

[YES]

Pressing the lock push-button terminates the

conversation (default in model /F of monitor).

[NO] The lock push-button operates normally from

version 4 of monitor and entrance panels

V.V. On/Off ->

[YES]

To activate the audio line press the push-but-

ton talk/listen. To deactivate the audio line press

the push-button again (default in model /F of mo-

nitor).

[NO] The talk/listen push-button must be hold

down to activate the audio line. From version 4 of

monitor and entrance panels.

Fine Ser.aut -> [YES] After the automatic door lock activation be-

cause of the Serr. Aut. flag with P6 close the inter-

phone or the video interphone cancels the call.

[NO] The possible automatic door lock does not

make the call end (default).

Force 2nd F. -> Valid only for some Vimar products.

[YES]

the square button (self-start) becomes

the second function regardless of the position

of the mechanical switch.

[NO] has the self-start function.

VIMAR Home A. -> Valid only for some Vimar products.

[YES] there is home automation.

[NO] (Default)

ACK Ring Exc. -> Valid for all, except 8879. Usually used for a

group master.

[YES] the call is accepted, and then the sec

ondary units ring, even if the group master has

ringtone off and therefore does not ring.

[NO] if a group master turns off the ringtone

none rings and there is a warning on the

entrance panel.

I. C. unlimit. -> [YES] the device has no timeout for the inter

communicating conversation. For it to work

properly, both parties talk ing to each other

must have it on YES.

[NO] (Default) and the intercommunicating

conversation lasts at most 5 minutes.

Risp.Automat -> [YES] After the panel ring tones the monitor

answers automatically. Even the flag must be

set to YES V.V. ON/OFF.

[NO] No automatic answer (default).

Group F.P. -> [YES] If it is programmed for a head group, this

latter, at the call reception from the push-button

module type 6120, will inform the other mem

bers that it is ringing. If it is programmed for the

group members, they will answer at the call from

a type 6120 to their head group ringing. In this

way it is possible to divide the calls between

external, internal and outdoor calls.

[NO] No reaction.

ID list and respective secondary (video)interphones Due Fili

Elvox (= 2 wire Elvox)

In the following table there is the list of the secondary IDs, for

each primary from 1 to 50, which are automatically used follo-

wing the procedure :”Assignation of the secondary Identification

Codes”, described in the instructions of the single

(video)interphones.

PRIMARIO

SECONDARIO

151 52 53

254 55 56

357 58 59

460 61 62

563 64 65

666 67 68

769 70 71

872 73 74

975 76 77

10 78 79 80

11 81 82 83

12 84 85 86

13 87 88 89

14 90 91 92

15 93 94 95

16 96 97 98

17 99 100 101

18 102 103 104

19 105 106 107

20 108 109 110

21 111 112 113

22 114 115 116

23 117 118 119

24 120 121 122

25 123 124 125

26 126 127 128

27 129 130 131

28 132 133 134

29 135 136 137

30 138 139 140

31 141 142 143

32 144 145 146

33 147 148 149

34 150 151 152

35 153 154 155

36 156 157 158

37 159 160 161

38 162 163 164

39 165 166 167

40 168 169 170

41 171 172 173

42 174 175 176

43 177 178 179

44 180 181 182

45 183 184 185

46 186 187 188

47 189 190 191

48 192 193 194

49 195 196 197

50 198 199 200

PRIMARY

SECONDARY

SECONDARY SECONDARY

POWER SUPPLY 6922

DESCRIPTION

Main power supply for ELVOX 2-WIRE audio and video door entry systems.

TECHNICAL SPECIFICATIONS

- Supply voltage 100-260V AC 50-60 Hz 60W

- Output voltage 1/2, B1/B2: 30V DC

- Current supplied see table 1

- Protection inside primary winding with fuse F 3.15 AL 250V

- The power supply unit has two types of protection, indicated as fol-

lows.

A yellow LED indicates:

- if lit steadily, it indicates the presence of power at the output.

- if flashing, the probable presence of a short-circuit on the twisted pair

- if off, it is possible there is a short-circuit on the output or near to the

power supply unit

A red LED indicates: a prolonged overload (current higher than the

continuous current for an excessive period of time).

If the Red LED is on, to restore operation it is necessary to unplug the

load or disconnect the power supply unit from the mains for at least 60

seconds.

- Operating temperature 0°C +45°C

- Maximum overall dimensions 140x115x65 mm.

INSTALLATION

The power supply can be wall-mounted using the screws and plugs sup-

plied, or in cabinets fitted with DIN rails (occupying a space of 8 modules).

Make installation of a bipolar switch on the power mains.

Operating times

The monitor, camera, lock and auxiliary services must operate according

to the following intermittent cycles.

Table 1

Mains voltage Continuous current + Intermittent current

(80 seconds ON +

120 seconds OFF)

110V 0,8A 0,4A

117V 0,8A 0,4A

125V 0,8A 0,5A

230V 0,8A 0,8A

240V 0,8A 0,8A

Page is loading ...

Elvox ART. 89F4/T Operating instructions

Brand: Elvox

Model: ART. 89F4/T

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Elvox ART. 89F4/T Operating instructions

This manual is also suitable for

Elvox ART. 89F4/T Operating instructions

Related papers

Other documents