GSS PMDF 1000 Assembly Instructions Manual

Brand: GSS

Model: PMDF 1000

Category: Routers

Type: Assembly Instructions Manual

This manual is also suitable for

HMPT 1000 FM

English

CLASS

KLASSE

PMDF 1000

Head-End Modulator FM

IP to 12xFM

GSS

Grundig SAT Systems GmbH

Beuthener Strasse 43

D-90471 Nuremberg

Phone: +49 (0) 911 / 703 8877

Fax: +49 (0) 911 / 703 9210

E-mail: [email protected]

Internet: http://www.gss.de

- 2 - PMDF 1000

Contents

1 Safety regulations and notes ..............................................................................3

2 General information ..........................................................................................4

2.1 Packing contents ................................................................................ 4

2.2 Meaning of the symbols used ............................................................... 4

2.3 Technical data.................................................................................... 5

2.4 Description ........................................................................................ 6

2.5 Software query .................................................................................. 7

3 Assembly ..........................................................................................................8

3.1 Installing the cassette .......................................................................... 8

3.2 EMC regulations ................................................................................ 9

3.3 Cassette overview ............................................................................ 10

3.4 Connecting the cassette ..................................................................... 10

4 The control panel at a glance ...........................................................................11

4.1 Menu items ...................................................................................... 11

4.2 Control panel ................................................................................... 11

5 Programming ..................................................................................................12

5.1

Programming procedure .........................................................................12

5.2 Programming the cassette .................................................................. 14

Selecting the cassette ........................................................................ 14

Setting the Ethernet parameters .......................................................... 15

Setting the IP address of the cassette .............................................. 15

Setting the address range ............................................................. 16

Setting the address of the gateway ................................................ 16

Setting the UDP port.......................................................................17

Setting the input parameters............................................................... 17

Selecting the transmission protocol ................................................ 18

Setting the port number ................................................................ 18

Setting the IP address of the input transport stream .......................... 19

Delete programme locations .............................................................. 20

Programme locations ........................................................................ 21

Submenus output parameters ............................................................. 21

Output frequency ........................................................................ 23

Channel selection ........................................................................ 23

Language selection ...................................................................... 24

Frequency deviation adjustment .................................................... 24

Kind of transmission .................................................................... 25

RDS ........................................................................................... 25

Output level ..................................................................................... 26

Factory reset .................................................................................... 26

Saving settings ................................................................................. 27

6 Final procedures ..............................................................................................28

- 3 - PMDF 1000

1 safety regulations and notes

• Assembly, installation andservicingshould be carried out byauthorised

electricians.

 • Switchofftheoperatingvoltageofthesystembeforebeginningwithassem-

bly or service work or pull out the mains plug.

 • Donotperforminstallationandserviceworkduringthunderstorms.

 • Installthesystemsoitwillnotbeabletovibrate…

 - inadust-free,dryenvironment

 - insuchamannerthatitisprotectedfrommoisture,fumes,splashingwa-

ter and dampness

- somewhere protected from direct sunlight

- not within the immediate vicinity of heat sources

- in an ambient temperature of 0 °C to +50 °C. In case of the formation of

condensation wait until the system is completely dried.

 • Ensurethatthehead-endstationisadequatelyventilated.Donotcoverthe

ventilation slots.

 • Bewareofshortcircuits

 • Noliabilityisacceptedforanydamagecausedbyfaultyconnectionsor

inappropriate handling.

 • Observetherelevantstandards,regulationsandguidelinesontheinstalla-

tion and operation of antenna systems.

 • ThestandardsIEC/EN/DINEN50083resp.IEC/EN/DINEN60728must

be observed.

 • For further information please read the assembly instructions for the head-

end station used.

• Test the software versions of the head-end station and the cassette and

update them if necessary. The current software versions can be found at

”www.gss.de”.

Take action to prevent static discharge when working on the device!

Electronic devices should never be disposed of in the household rubbish. In

accordance with directive 2002/96/EC of the European Parliament and the

European Council from January 27, 2003 which addresses old electronic and

electrical devices, such devices must be disposed of at a designated collection

facility. At the end of its service life, please take your device to one of these

public collection facilities for proper disposal.

- 4 - PMDF 1000

2 general information

2.1 PaCking Contents

1 Cassette PMDF 1000

1 LAN cable

1 Brief assembly instructions

1 Messprotokoll

2.2 meaning of the symbols used

Important note

—> General note

 •  Performingworks

- 5 - PMDF 1000

2.3 teChniCal data

The devices meet the following EU directives:

 2006/95/EC,2004/108/EC

The product fulfils the guidelines and standards for CE labelling (see page 29).

Unless otherwise noted all values are specified as “typical”.

LAN interface

Standard: .............................................................................100-BASE-T

Data rate: ............................................................................... ≤ 80 MBit

Protocols: .......................................................... UDP(UserDataProtocol),

RTP (Real-Time Transport Protocol)

Conversion: .................................................................. MPTS to UHF FM

HF output

Frequency range .......................................... 87.50MHz…108.00MHz

Tuning steps ................................................................................50 kHz

Type of modulation ............................................................................ FM

Return loss ......................................................................................8 dB

Output level .............................................................................. 93 dBμV

Signal-to-harmonics ratio ..............................................................>60 dB

Output impedance ..........................................................................75 Ω

External voltage difference

Mono ........................................................................................66 dB

Stereo .......................................................................................53 dB

Non-linear distortion factor

Mono .......................................................................................0,06%

Stereo ........................................................................................0,6%

Overall output frequency deviation ................................................75 kHz

FM modulator

Number of available services (programme locations) ..............................12

RDS signal processing .................................................................. 57 kHz

Pilot signal .................................................................................. 19 kHz

Preemphasis ...................................................................................50 μs

Connections

LAN input .......................................................................... 1 RJ45 socket

HF output ..................................................................1IECsocket,female

Connection strip ........................................................................... 10-pin

for supply voltages and control circuits

RS-232 socket: ..................................... serial interface for software update

- 6 - PMDF 1000

Remote maintenance

Remotely controllable (via PSW 1000*): ..............................................yes

Remote update (via BEflash*): .............................................................yes

(* and a corresponding management unit)

2.4 desCriPtion

The cassette converts 12 stereo audio channels from an IP data stream into 12

FM modulated stereo output signals. The RDS station code is automatically taken

from the IP data stream or can be entered manually.

Principle signal path:

HF output

LAN input

IP data stream

Combiner

12 fold modulator

TPS

The cassette is controlled with the head-end station control unit.

A LED indicates whether an input signal is present or not (see figure on page 5).

LED indicator Indication

Green Signal present

Red No signal

To operate this cassette the software version of the control unit must be “V44”

or higher. You can find the current operating software for the control unit and

thecassette,thesoftware“BE-Flash”andthecurrentassemblyinstructionson

the website “www.gss.de”.

The cassette is designed for use in head-end stations of the profi line.

- 7 - PMDF 1000

2.5 software query

Control unit

 If necessary, you can activate the indication of thesoftware version of the

control unit manually:

 • Pressanytwokeysonthecontrolunitofthehead-endstationsimultaneously

untilthedisplaygoesdarkandthesoftwareversion,e.g.“V 44” appears.

Cassette

After activating the cassette the software version of the cassette is displayed

(see page 14).

- 8 - PMDF 1000

3 assembly

3.1 installing the Cassette

– Ensure the head-end station is mounted so it will not be able to vibrate.

Avoid,forexample,mountingthehead-endstationontoaliftshaftorany

other wall or floor construction that vibrates in a similar way.

– Before installing or changing a cassette unplug the power cable from the

mains power socket.

 • Removethefasteningscrews1 of an unoccupied slot from the bracket of

the head-end station.

 • Insertthecassetteinthisslotandpushitintothehousing.

 • Alignthecassetteandapplyslightpressuretoconnectittotheconnections

of the board and the HF bus bar.

 • Fastenthecassettewiththescrews1.

- 9 - PMDF 1000

3.2 emC regul ations

To comply with the current EMC regulations, it is necessary to connect the lines

leading in and out of the head-end station using cable terminals.

When mounting the cassette in a head-end station which is installed in a 19”

cabinet, make sure the connections leading in and out for the 19” cabinet are

made using cable terminals.

CLASS

KLASSE

The attenuation of shielding of the connection lines for ASI and antenna must

meet the requirements for “Class A”.

 • Inserttherequirednumberofcableterminalsintheopeningsprovidedin

the head-end station or in the 19

”

cabinet.

Tighten the nuts on the cable terminals until the teeth on the lock washer have

penetrated the exterior coating and a good connection is made between the hous-

ing and cable terminals.

- 10 - PMDF 1000

3.3 Cassette overview

1 D-SUB socket “RS 232“

2 not used

3 not used

4 not used

5 Status LED of the LAN interface

(yellow LED – data transfer)

6 not used

7 Status LED of the LAN interface

(green LED – network connection)

8 not used

9 Status LED of the LAN input

0 not used

not used

@ MAC address

The operating software of the cassette can be updated via the

9-pin D-SUB socket “RS 232” using a PC or notebook and the

software “BE-Flash”. You can find the current operating software

on the website

“www.gss.de”.

3.4 ConneCting the Cassette

 • PlugtheLANinputcableintotheLANinputsocket.

 • Connectthehead-endstationtothemains.

- 11 - PMDF 1000

4 the Control Panel at a glanCe

4.1 menu items

Programme the

cassette

using the buttons on the control unit of the head-end

station. The two-line display of the control unit then shows the menus.

The parameters and functions to be set are underlined.

Use the key to select the following main menu items:

– Ethernet parameters

– Input parameters

– Deleting services (programme locations)

– Output parameters

– Output level

– Factory reset

4.2 Control Panel

The key pad on the head-end station is used to scroll through the menus:

scrolls forward through the menus.

select parameters in the menus.

setvalues,initiateactions.

selects sub-menus.

scrolls backward through the menus.

saves all entries.

BE-Remote V44

PROFESSI ONAL

- 12 - PMDF 1000

5 Programming

5.1

Programming ProCedure

Ein / On

BE–Remote

please wait …

V 44

Box 4

V 1

IP-FM

– – –

Bx 1A

C5-12,S3-24

TWIN-SAT

C07

Böx 4

C5-12,S3-24

TWIN-SAT

C07

Box 5

..............

t > 10 s

FM 01

Bayern 1

87.50

Bx 4

LEVEL

0 dB

FM 01

87.50

FREQ

=> auto

Senderauswahl

Station selection

FM 01 RA

Bayern 1

001/091

Sprachauswahl

Language selection

FM 01

01/01 ger

AUDIO

Hubanpassung

Deviation adjustment

FM 01

0.0 dB

VOLUME

<=>C

FM 01 AUDIO

AUTO

FM 01

Bayern 1

RDS-NAME

=> auto

0 … - 10 dB

Bx 4

FM =>

SERVICES

CLEAR ALL

▶

Box …

………

……

AUTO / MONO / STEREO

▶

Bx 4

Defaults

FACTORY

Bx 4

STORE

FACTORY

=> M

auf Werkseinstellung

zurücksetzen und speichern

reset to factory defaults

and store

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

< zu klein too small

= OK

C Begrenzung clipping

> zu groß too big

Bx 4

stat =>

ETHERNET

Options

stat / DHCP

Bx 4

192.168. 1. 1

IP-GATEWAY

Bx 4

255.255.255. 0

IP-MASK

▶

◀

Bx 4

192.168. 1.169

IP-ADDR

▶

◀

▶

◀

Bx 4

60000

UDP-PORT

▶

◀

▶

0 … 65535

Bx 4

UDP

MODE/PORT

1234

▶

◀

Bx 4

227. 40.

IP-INPUT

50. 60

▶

◀

UDP / RTP,

0 … 65535

Bx 4

LAN

INPUT

OK =>

Bedienhinweise

"blättert" Menüs vorwärts.

"blättert" Menüs rückwärts.

wählen die Eingabeposition

wählt Untermenü

stellen Werte ein,.

speichert alle Eingaben.

1 zeigt die Eingabeposition

Operating Hints

scrolls forward through the menu.

scrolls backward through the menu.

select the enter position.

selects a submenu.

set values and triggers actions.

saves all entries.

1 shows the enter position

Seite 13

- 13 - PMDF 1000

Ein / On

BE–Remote

please wait …

V 44

Box 4

V 1

IP-FM

– – –

Bx 1A

C5-12,S3-24

TWIN-SAT

C07

Böx 4

C5-12,S3-24

TWIN-SAT

C07

Box 5

..............

t > 10 s

FM 01

Bayern 1

87.50

Bx 4

LEVEL

0 dB

FM 01

87.50

FREQ

=> auto

Senderauswahl

Station selection

FM 01 RA

Bayern 1

001/091

Sprachauswahl

Language selection

FM 01

01/01 ger

AUDIO

Hubanpassung

Deviation adjustment

FM 01

0.0 dB

VOLUME

<=>C

FM 01 AUDIO

AUTO

FM 01

Bayern 1

RDS-NAME

=> auto

0 … - 10 dB

Bx 4

FM =>

SERVICES

CLEAR ALL

▶

Box …

………

……

AUTO / MONO / STEREO

▶

Bx 4

Defaults

FACTORY

Bx 4

STORE

FACTORY

=> M

auf Werkseinstellung

zurücksetzen und speichern

reset to factory defaults

and store

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

FM 01…12

FM 12…01

< zu klein too small

= OK

C Begrenzung clipping

> zu groß too big

Bx 4

stat =>

ETHERNET

Options

stat / DHCP

Bx 4

192.168. 1. 1

IP-GATEWAY

Bx 4

255.255.255. 0

IP-MASK

▶

◀

Bx 4

192.168. 1.169

IP-ADDR

▶

◀

▶

◀

Bx 4

60000

UDP-PORT

▶

◀

▶

0 … 65535

Bx 4

UDP

MODE/PORT

1234

▶

◀

Bx 4

227. 40.

IP-INPUT

50. 60

▶

◀

UDP / RTP,

0 … 65535

Bx 4

LAN

INPUT

OK =>

Bedienhinweise

"blättert" Menüs vorwärts.

"blättert" Menüs rückwärts.

wählen die Eingabeposition

wählt Untermenü

stellen Werte ein,.

speichert alle Eingaben.

1 zeigt die Eingabeposition

Operating Hints

scrolls forward through the menu.

scrolls backward through the menu.

select the enter position.

selects a submenu.

set values and triggers actions.

saves all entries.

1 shows the enter position

Seite 12

- 14 - PMDF 1000

5.2 Progr amming the Cassette

—> Pressing the button for longer than 2 seconds cancels the

programming procedure. This takes you back to the program item

“Selecting the cassette” from any menu. Any entries that have not

been saved are reset to the previous settings.

—> Entries in the menus can be saved by pressing the key. You are

taken back to the “Selecting the cassette” menu item.

—>

Pressing the

button returns to the previous menus.

 • Switchonthehead-endstation

Ein / On

BE–Remote

please wait …

V 44

t > 10 s

—> The display shows the software version (e.g. V 44)

—> The processor reads the

cassettes

‘ data (approx. 10 seconds).

seleCting the Cassette

Box 4

V 1

IP-FM

– – –

Bx 1A

C5-12,S3-24

TWIN-SAT

C07

Böx 4

C5-12,S3-24

TWIN-SAT

C07

Box 5

..............

Box …

………

……

 • Selectthe

cassette

you want to program (e.g. Box 4) by repeatedly pressing

the button if necessary.

—>

The display shows e.g. the menu "Box 4 IP-FM":

"Box 4" stands for

slot

4,

IP-FM

" type of cassette

"V 1" software version of the cassette

 • Pressthe button.

—> The “Setting the Ethernet parameters” – “ETHERNET” menu is activated.

- 15 - PMDF 1000

setting the ethernet Parameters

In this menu you specify whether the Ethernet parameters for the cassette are

entered automatically by a connected server (“DHCP”),orwhetheryouwant

to enter them manually (“stat”).Toassignthecassetteuniquely,eachIPTVcas-

sette must be allocated its own IP address.

Bx 4

stat =>

ETHERNET

Options

 • Pressthe buttons to select manual setting (”stat”) or automatic setting

(”DHCP”) of the Ethernet parameters.

 • Pressthe

button to activate the setting options

(”Options”)

—> The “Setting the IP address of the cassette”

– menu “IP-ADDR” is

activated.

set ting the iP address of the Casset te

 IfyouchoosetoentertheEthernetparametersmanually,settheIPaddressof

the cassette in this menu. If “DHCP”isselected,the“IP-ADDR”,“IP-MASK” and

“IP-GATEWAY” sub-menus display the parameters that were assigned automati-

callybyaconnectedserver.Ifaserverisnotconnected,“  0.  0.  0.  0*”

appears in the corresponding menu. The star “ * ” in the display means that

the data is provided by a DHCP server.

Bx 4

192.168. 1.169

IP-ADDR

 • Usethe

buttons to place the cursor under the digit of the IP address

displayed to be set and use to set the IP address wished.

 • Pressthe

button.

—> The “Setting the address range”

– “IP-MASK” menu is activated.

- 16 - PMDF 1000

setting the address range

In this menu you define the address range for the cassettes connected to the

LAN network.

Bx 4

255.255.255. 0

IP-MASK

 • Usethe

buttons to place the cursor under the digit of the IP address

displayed to be set and use to set the IP address wished.

 • Pressthe

button.

—> The “Setting the address of the gateway”

– “IP-GATEWAY” menu is

activated.

setting the address of the gateway

The address of a gateway (server) can be set in this menu. If no gateway is

used you can skip this setting.

Bx 4

192.168. 1. 1

IP-GATEWAY

 • Usethe

buttons to place the cursor under the digit of the IP address

displayed to be set and use to set the IP address wished.

 • Pressthe

button.

—> The “Setting the UDP port”

– “UDP-PORT” menu is activated.

- 17 - PMDF 1000

setting the udP Port

 TheUDPportsettingisrequiredif,e.g.forfurtherfunctionsexternalaccessis

necessary and port 60000 is already in use.

At this time UPD port setting is not needed.

Bx 4

60000

UDP-PORT

 • Usethe

buttons to place the cursor under the digit of the port number

displayed to be set and use to set the port number wished (”0”…

”65535”).

 • Pressthe button.

—> The “Setting the input parameters” – “INPUT” main menu is activated.

set ting the inPut Par a meters

Via this menu you have access to the submenus for the input parameters.

Bx 4

LAN

INPUT

OK =>

 • Pressthe

button.

—> The“Selectingthetransmissionprotocol,settingtheportnumber”–

“MODE / PORT” menu is activated.

—> With the button the input parameter settings are skipped.

The menu “Delete programme locations” – “SERVICES” is activated.

- 18 - PMDF 1000

seleCting the transmission ProtoCol

setting the Port number

In this menu you can define the transmission protocol and the port number.

Bx 4

UDP

MODE/PORT

1234

Selecting the transmission protocol

 • Pressthe button to position the cursor under ”UDP” or “RTP”.

 • Usingthe buttons to select the transmission protocol wished:

“UDP” – The User Datagram Protocol is for the connectionless transmission of

data to a certain application. The port number of the service is also

sent which the data should obtain.

“RTP” – The Real-time Transport Protocol is for continuously transmitting mul-

timedia data streams in an IP network. Unlike UDP, the header is

transmitted which makes the data transmission more robust.

Setting the port number

 • Press the button to position the cursor under the port number e.g.

” 1234”.

 • Use the buttons to position the cursor under the digit of the port

number displayed to be set.

 • Usingthe buttons set the port number wished.

 • Pressthe button.

—> The “Setting the IP address of the input transport stream” –

“IP-INPUT” menu is activated.

- 19 - PMDF 1000

setting the iP address of the inPut transPort stream

In this menu you can set the IP address of the transport stream fed via the LAN

interface.

Bx 4

227. 40.

IP-INPUT

50. 60

 • Usethe buttons to position the cursor under the digit of the IP ad-

dress displayed to be set.

 • Usingthe buttons set the IP address wished.

—> Whether a input signal is present or not is indicated by a status LED.

9 Status LED LAN input

LED indicator Indication

Green Signal present

Red No signal

 • Pressthe button.

—> You will be returned to the menu item “Setting the input parameters”

– “INPUT”.

 • Pressthe button.

—> The menu “Delete programme locations” – “SERVICES” is activated.

- 20 - PMDF 1000

delete Programme loCations

In this menu you can delete the programme locations preset in the factory resp.

"old" programme locations (e.g. if the input parameter setting was changed).

Bx 4

FM =>

SERVICES

CLEAR ALL

 • Deletetheprogrammelocationsusingthe button.

—> Allprogrammelocationsaredeleted,thestoredFMfrequencieswill

be remain.

 Aslongasnoradiostationisassignedtoaprogrammelocation,

the transmitter is switched off.

—> A "Factory Reset" resets to the programme locations preset in the

factory.

 • Pressthe button.

—> The “Output parameters” – “FM 01” menu is activated.

Page is loading ...

GSS PMDF 1000 Assembly Instructions Manual

Brand: GSS

Model: PMDF 1000

Category: Routers

Type: Assembly Instructions Manual

This manual is also suitable for

HMPT 1000 FM

Download PDF

report

GSS PMDF 1000 Assembly Instructions Manual

This manual is also suitable for

GSS PMDF 1000 Assembly Instructions Manual

Related papers

Other documents