Falcon RM70 Installation guide

Brand: Falcon

Model: RM70

Type: Installation guide

RM70, RM70A, RM170, and RM170A

Removable Mullions

PAGE NO. REVISION

1 of 2

4270108237

Installation Instructions

1. Prepare frame header for filler or adapter plate.

Install filler or adapter plate and top bracket.

For RM70 and RM170, see Figures 1 and 2.

(Filler, filler mounting screws, and bracket

mounting screws by others.)

For RM70A and RM170A, see Figures 3 and 4.

2. Prepare floor and threshold for bottom bracket.

Install bottom bracket (Figures 5 and 6, other

side).

3. Cut mullion to length from top (Figures 7 and 8,

other side).

4. Slide mullion over top fitting and swing into

position on bottom fitting (Figure 9, other side).

5. Slide mullion clamp over top fitting and secure

with three screws (Figure 10, other side).

6. Install security clips on door (Figure 11, other

side).

Figure 2. Filler and top bracket installation (RM70

and RM170).

Filler (by others) flush

with stop, centered on

center line of doors

doors

10-32 x 1/2" FPHMS

(by others)

Figure 4. Adapter plate and top bracket

installation (RM70A and RM170A).

Install top bracket to

adapter plate with three

10-32 x 1/2" FPHMS

#10 x 1" FPHMS

4 places

9/16"

1-11/16"

2-3/4"

1-5/8"

doors

Door

Figure 1. Header and filler preparation for top

bracket (RM70 and RM170).

Filler (by

others)

Drill and tap header and filler

for 10-32 screws, 3 places

Top bracket

location

Figure 3. Header preparation for adapter plate

(RM70A and RM 170A).

View

looking up

Adapter plate

11/32"

1-27/32"

1-1/8"

2-1/4"

1-1/2"

doors

Prepare header for #10 x 1"

FPHSMS, 4 places

Adapter

plate location

Adapter plate

Door

View looking up

Customer Service

1-877-671-7011 www.allegion.com/us

Printed in U.S.A.

4270108237 Rev. 12/16-f

RM70, RM70A, RM170, and RM170A

Removable Mullions

PAGE NO. REVISION

2 of 2

Figure 6. Bottom bracket installation.

#14 x 1" screw anchors

in floor, 3 places

#10 x 1" FPHSMS

3 places

Figure 5. Floor and threshold preparation

for bottom bracket.

Figure 7. Required mullion length.

3/4"

1/4"

Cut mullion

1/16" less

than this

dimension

Top

bracket

Bottom

bracket

Figure 9. Install mullion.

Figure 11. Position door stabilizer clips as shown, drill and

tap door 10-32, 4 places, and install door stabilizer clips.

10-32 x 1/2" FPHMS

4 places

1/32"

min.

1/32"

min.

Frame stabilizer clips

on mullion (mullion

not shown for clarity)

Door stabilizer clips

4270108237

Figure 10. Slide mullion clamp up over

top bracket and secure with screws.

10-32 x 3/8"

slotted truss head MS

3 places

Figure 8. Cut mullion to length.

Clamp

Header not

shown for

clarity

7/8"

1-11/16"

2-3/4"

1-5/8"

Prepare floor for #14 x 1"

screw anchors, 3 places

doors

Door

Cut out threshold

for bottom bracket

View

looking

down

1 Slide mullion

over top

bracket

2 Swing mullion

into position on

bottom bracket

11"

66"

Cut top end

CAUTION: There is

a steel tube inside

of the mullion

4-3/4"

approx

of latchbolt

Customer Service

1-877-671-7011 www.allegion.com/us

Printed in U.S.A.

4270108237 Rev. 12/16-f

Falcon RM70 Installation guide

Falcon RM70 Installation guide

Falcon RM70 Installation guide

Related papers

Other documents