2. H3C
  3. LSVM1106SFAN
LSVM1106SFAN

H3C LSVM1106SFAN, LSVM2106SFAN User manual

  • Hello! I am an AI chatbot trained to assist you with the H3C LSVM1106SFAN User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
H3C LSVM1106SFAN &
LSVM2106SFAN
Fan Modules User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: 6PW102-20170515
Copyright © 2011-2017, New H3C Technologies Co., Ltd. and
its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or
by any means without prior written consent of New H3C Technologies
Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care,
, IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter,
SecBlade, Comware, ITCMM and HUASAN are trademarks of New
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any
kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this product
must meet the applicable national laws and regulations.
Obtaining documentation
To access the most up-to-date H3C product documentation, go to the
H3C website at http://www.h3c.com.hk
.
To obtain information about installation, configuration, and maintenance,
click http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes,
click http://www.h3c.com.hk/Software_Download
Technical support
service@h3c.com
http://www.h3c.com.hk
Documentation feedback
You can email your comments about product documentation to
[email protected].
We appreciate your comments.
i
Contents
Fan tray overview ···················································································· 1
LSVM1106SFAN ················································································ 1
Introduction to LSVM1106SFAN ················································· 1
LSVM1106SFAN specifications ·················································· 3
LSVM2106SFAN ················································································ 3
Introduction to LSVM2106SFAN ················································· 3
LSVM2106SFAN specifications ·················································· 5
Installing and replacing a fan tray ························································· 6
Installing a fan tray ············································································ 6
Replacing a fan tray ·········································································· 8
1
Fan tray overview
LSVM1106SFAN
Introduction to LSVM1106SFAN
The LSVM1106SFAN is a fan tray with blowing fans that blow air to the
inside of the device. It comprises five separate fans. The LSVM1106SFAN
features small size, fast heat dissipation, and hot swapping, and can
automatically adjust the fan speed based on the device temperature.
The fan tray provides a status LED on the front panel to show the
operating status of the fans. When the fans operate properly, the LED is
green. If the LED is red or off, the fans operate abnormally. Figure 1
sh
ows the structure and airflow of the fan tray.
2
Figure 1 LSVM1106SFAN structure
(1) Captive screw (2) Status LED
(3) Handle (4) Airflow direction label
(5) Airflow
3
LSVM1106SFAN specifications
Table 1 LSVM1106SFAN specifications
Model Item Specification
LSVM1106SF
AN (Fans
blow air from
outside of the
device)
Fans
Five 60 × 60 × 38 mm (2.36 ×
2.36 × 1.50 in) fans
Max fan speed
11000 rpm (revolutions per
minute)
Max airflow
135 CFM (cubic foot per
minute)
Max power
consumption
75.5 W
Min power
consumption
4.4 W
LSVM2106SFAN
Introduction to LSVM2106SFAN
The LSVM2106SFAN is a fan tray with drawing fans that draw air from
the inside of the device. It comprises five separate fans. The
LSVM2106SFAN features small size, fast heat dissipation, and hot
swapping, and can automatically adjust the fan speed based on the
device temperature. The fan tray provides a status LED on the front panel
to show the operating status of the fans. When the fans operate properly,
the LED is green. If the LED is red or off, the fans operate abnormally.
Figure 2 shows the structure and airflow of the fan tray.
4
Figure 2 LSVM2106SFAN structure
(1) Captive screw (2) Status LED
(3) Handle (4) Airflow direction label
(5) Airflow
5
LSVM2106SFAN specifications
Table 2 LSVM2106SFAN specifications
Model Item Specification
LSVM2106SFAN
(Fans blow air from
inside of the device)
Fans
Five 60 × 60 × 38
mm (2.36 × 2.36 ×
1.50 in) fans
Max fan speed 11000 rpm
Max airflow 135 CFM
Max power
consumption
75.5 W
Min power
consumption
4.4 W
6
Installing and replacing a fan tray
You can install and replace the LSVM1106SFAN and LSVM2106SFAN
in the same way. For more information, see “Installing a fan tray“ and
“Replacing a fan tray.”
Installing a fan tray
IMPORTANT:
Before installing a fan tray, make sure that the airflow direction of
the module meets the ventilation requirement at the installation site.
For more information, see Figure 1 and Figure 2.
Follow these steps to install a fan tray:
Step1 Wear an ESD-preventive wrist strap, and make sure that it
makes good skin contact and is properly grounded.
Step2 As shown in Figure 3, u
se a screwdriver to loosen the captive
screws on the filler panel of the fan tray slot, and then remove
the filler panel.
Step3 Unpack the fan tray. Holding the fan tray with both hands with
the upside (marked with an airflow direction label) on top,
gently push the fan tray into the slot along the guide rails until
the fan tray completely seats into the slot, as shown in Figure 4.
Step4 U
se a Phillips screwdriver to fix the captive screws on the fan
tray to secure it into the switch chassis.
Step5 When the switch is running, check the status LED of the fan tray.
If the LED displays green, the installation is correct.
7
Figure 3 Install a fan tray (I)
Figure 4 Install a fan tray (II)
8
CAUTION:
• If you insert the fan tray with the upside facing downward, you
cannot completely insert the module into the slot. If this happens,
pull the fan tray out and then insert it again with the upside on
top.
• If you cannot fix the captive screws, check whether the fan tray is
correctly installed.
Replacing a fan tray
CAUTION:
• When replacing a fan tray from a running switch, be cautious of
electricity hazards, and do not touch the rotating fans to avoid
bodily injury.
• After you unplug a fan tray from a running switch, install a new
fan tray within six minutes to ensure proper ventilation and heat
dissipation of the switch.
When the fan tray is faulty, you must replace it.
Follow these steps to replace a fan tray:
Step1 Prepare an antistatic bag for the removed fan tray.
Step2 Wear an ESD-preventive wrist strap, and make sure that it
makes good skin contact and is properly grounded.
Step3 As shown in callout 1 of Figure 5,
use a screwdriver to loosen
the captive screws of the fan tray.
9
Step4 As shown in callout 2 of Figure 5,
holding the handle of the fan
tray, pull the fan tray out of the chassis.
Step5 Put the removed fan tray into the antistatic bag.
Step6 Install a new fan tray. For more information, see “Installing a
fa
n tray.”
Figure 5 Remove a fan tray
(1) Loosen the captive screws of the fan tray
(2) Pull the fan tray out of the chassis
10
NOTE:
If you replace a fan tray from a running switch, and the airflow
direction of the new fan tray is different from the former one, the
alarm message System fan airflow direction is not preferred on
slot X, please check it. appears. To eliminate the alarm, replace
another fan tray with the same airflow direction, or use the fan
prefer-direction slot
slot-number
{ power-to-port | port-to-power }
command in system view to change the preferred airflow direction
of the switch.
/