Visual Comfort Studio CHC 2166GI Installation guide

Visual Comfort Studio
Brand
Visual Comfort Studio
Model
CHC 2166GI
Type
Installation guide

This manual is also suitable for

ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Drill 8 holes (J) on the ceiling and make sure the hole distance will match to
mounting plate (C) holes
2. Knock the anchors (B) into the pre-drilled holes in the ceiling (J).
3. Install the mounting plate (C) with ceiling loop (F) to outlet box by using
mounting screws (E) provided.
4. Attach mounting screws (D) provided on the anchors (B) and tighten.
5. Put canopy (G) to ceiling loop, and secure with lock collar (H).
6. Using the dimensions of the fixture as a guide, shorten the chain (K) as needed
using a pair of chain pliers.
7. Take into consideration that you will use the chain end link to mount the
chandelier once you have removed the excess chain.
8. Unscrew the threaded collar on the chain end link. Attach the chain to the
ceiling loop (F). Close the threaded collar to secure the chain.
9. Unscrew the threaded collar on the other chain end link. Raise the fixture and
attach chain end link to the top ring (I). Close the threaded collar to secure the
fixture body.
10. Unwrap the wiring from the top of the fixture body. Weave the power supply
cord and the ground wire through the chain (K).
11. When you reach the canopy and ceiling loop, measure the wires and cut. Be
certain to leave enough to connect inside the canopy.
12. Strip the insulation back on the two power supply wires about 5/8”.
13. Twist the power supply and ground wires together and push through the center
hole in the ceiling loop.
DRY
Darlana Linear Pendant
Item # CHC2166
ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
14. Loosen the clock collar (H); let the canopy (G) slip down the chain carefully.
15. Connect the Ground (bare) fixture wire with the ground (usually bare) wire from
your ceiling box using wire nut (A). If you house does not have ground wire,
then attach this wire to the green grounding screw inside of outlet box.
IT IS IMPERATIVE THAT THE J-BOX IN YOUR HOME BE PROPERLY
GROUNDED.
16. Connect the Neutral fixture wire with the Neutral (usually white) wire from your
ceiling box using wire nut (A).
17. Connect the Hot (smooth edge, markings, or black) fixture wire with the Hot
(usually black) wire from your outlet box using wire nut (A).
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY
WILL BE COMPROMISED.
18. Tuck these wire connections neatly into ceiling loop (F) to secure.
19. Put canopy (G) to ceiling loop, and secure with lock collar (H).
20. Install the light bulbs (not included) into sockets.
21. Installation is complete, turn on power at fuse or circuit breaker.
DRY
Darlana Linear Pendant
Item # CHC2166
  • Page 1 1
  • Page 2 2

Visual Comfort Studio CHC 2166GI Installation guide

Visual Comfort Studio
Brand
Visual Comfort Studio
Model
CHC 2166GI
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents