INSTALLATION INSTRUCTIONS
For item#N7764-683 (Convertible Lamps for Pendant) (Rev. 4/17/2019)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 3
PREPARING FOR INSTALLATION (Fig. 1&Fig. 3)
1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to misplace any small parts
necessary for installation.
3. Place the acrylic board (H) and decorative metal sheet (I) into
the metal bracket (J) of crossbar beam and bottom sheet (P),
and secure with screws (G) at both ends.
4. Secure tube (T) to fixture body, and thread nipple of tube
assembly thru crossbar beam (F), secure with fixture loop (A).
5. Attach metal plate (K) to bracket (J) by using screws (E).
6. Thread the nipple into the ceiling loop until snug.
7. Thread the other end of the nipple into the crossbar until
snug. Note: The length of the nipple into the crossbar may be
adjusted if necessary.
8. Use the lock washer and hex nut to secure the nipple into the
crossbar.
9. Take this crossbar assembly and mount it to ceiling outlet box
with mounting screws (Size: #8-32N*L0.5"). The side of
crossbar marked with “GND” must face out.
10. Determine the desired hanging height and use a pair of
proper chain pliers to remove and discard the excess chain.
11. Open the quick link and connect to the fixture loop and end of
chain, then close the quick link.
12. Carefully lace the fixture’s wires through the chain, slip lock
collar, canopy over the chain and wire, carefully let these
parts rest on the fixture loop.
13. Open the other quick link to connect other end link of chain to
the ceiling loop on the canopy. Then close the quick link.
14. Feed the fixture wires through the loop and nipple assemble.
CONNECTING THE WIRES (Fig. 2)
15. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the crossbar using the green screw provided.
16. Tuck the wire connections neatly into the ceiling outlet box.
Raise the canopy to the ceiling and secure it with the lock
collar to the ceiling loop.
COMPLETING THE INSTALLATION (Fig. 3)
17. Place the candle covers (C) over the sockets (B).
18. Install (4) four candelabra base bulbs (D) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with
the fixture specification — DO NOT EXCEED THE
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig. 3) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-3096E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
Set# A-012
- Crossbar
- Ground screw
- Mounting Screw*2
Chain#HCH4072-GMS
Candle Cover# CCV21050P-710
Lock Washer
Nipple
Cross Bar
Outlet Box (Ceiling)
Ceiling loop
Lock Collar
Chain (End link)
Quick Link
Fixture Loop
Quick Link
Chain (End link)
Hex Nut
Mounting Screws
Canopy
Page: 1/2
T
G
B
F
J
E
K
A
D
C
I
H
P
INSTALLATION INSTRUCTIONS
For item#N7764-683 (Convertible Lamps for Semi Flush Mount)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUI T BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 4
Fig. 2
PREPARING FOR INSTALLATION (Fig. 4)
1. Shut off power at the fuse box or circuit breaker box
and remove the old fixture including the mounting
hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any
small parts necessary for installation.
3. Place the acrylic board (H) and decorative metal sheet
(I) into the metal bracket (J) of crossbar beam and
bottom sheet (P), and secure with screws (G) at both
ends.
4. Secure tube (T) to fixture body, and thread nipple of
tube assembly thru crossbar beam (F), secure with
canopy assemble (N).
5. Attach metal plate (K) to bracket (J) by using screws
(E).
6. Secure circular strap (L) to the outlet box using
mounting screws (Size: 8-32*1/2"L). The side of the
circular strap marked “GND” must face out.
7. The support cable is provided to support the weight of
the fixture while wiring. Align the fixture to mounting
plate (L) and attach hook (P) on the end of support
cable (M) into a slot located on mounting plate (L).
Carefully allow the support cable (M) to support the
weight of the fixture while wiring.
CONNECTING THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the circular strap (L)
using the green screw provided.
9. Tuck the wire connections neatly into the ceiling outlet
box.
COMPLETING THE INSTALLATION (Fig. 4)
10. Raise the canopy to the ceiling and secure with screws
(O).
11. Place the candle covers (C) over the sockets (B).
12. Install (4) four candelabra base bulbs (D) up to 60 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification— DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE
PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig. 4) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Set# A-012
- Circular strap
- Ground screw
- Mounting screw*2
Candle Cover# CCV21050P-710
Page: 2/2
LA-3096E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
P
Outlet Box (Ceiling)
L
Mounting
Screws
O
E
K
J
H
I
G
L
N
M
D
C
T
B
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Metropolitan N7784-248 User manual
-
-
-
-
-
-
-
Metropolitan N7785-248 User manual
-
-