Halo LZR212P Installation guide

Halo
Brand
Halo
Model
LZR212P
Type
Installation guide

Halo LZR212P is a mini track connector designed for use with LZR100 Series track systems. It allows for the connection of two sections of track and provides a secure and reliable electrical connection. The connector is easy to install, requiring only the loosening of a set screw, insertion of the connector into the open ends of the track, and tightening of the lock screws. The ground conductor must be on the same side of the sections of track being joined (polarity groove side).

Here are some of the key features and capabilities of the Halo LZR212P:

  • Easy to install
  • Provides a secure and reliable electrical connection

Halo LZR212P is a mini track connector designed for use with LZR100 Series track systems. It allows for the connection of two sections of track and provides a secure and reliable electrical connection. The connector is easy to install, requiring only the loosening of a set screw, insertion of the connector into the open ends of the track, and tightening of the lock screws. The ground conductor must be on the same side of the sections of track being joined (polarity groove side).

Here are some of the key features and capabilities of the Halo LZR212P:

  • Easy to install
  • Provides a secure and reliable electrical connection
Instrucciones de Instalacion
LZR Mini Conector
NOTA: El conductor de tierra debe estar del
mismo extremo que las secciones del riel que
se desea unir (extremo de acanaladura de
polaridad).
Paso 1. Afloje los tornillos prisioneros y retire
el conector de extremo terminal.
Paso 2. Presione el conector para que entre en
los extremos abiertos del riel.
Paso 3. Ajuste los tornillos prisioneros. No
apriete en exceso.
Installation Instructions For
LZR212 Mini-Connector
NOTE: Ground conductor must be on the
same side of sections of track being
joined (polarity groove side).
Step 1. Loosen set screw and remove dead
end fitting.
Step 2. Push connector into open ends of
track.
Step 3. Tighten lock screws. Do not
overtighten.
Instructions d’ Installation
LZR212 Mini Connecteur
Remarque: Le fil de terre doit se trouver de
même côté que les parties du rail étant reliées
(côté de la rainure de polarité).
Étape 1. Desserrer les vis de pression et
enlever le raccord de bout mort.
Étape 2. Pousser le connecteur dans les
extrémités ouvertes du rail.
Étape 3. Serrer les vis de pression. Ne pas
trop serrer.
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
1. Read all of these installation instructions before
installing the track system.
2.
Save These Instructions
and refer to them when additions or changes in the
track configuration are made.
3. Disconnect electrical power before adding to or
changing the configuration of the track.
4. For use with LZR100 Series track systems only.
5. Electrical ratings: 120V, 60Hz, 20A
INSTRUCTIONS D’ INSTALLATION
IMPORTANTES CONSIGNES DE
SÉCURITÉ
1. Pour l’installation ou l’utilisation du présent système
sur rail, veullez prendre des mesures de sécurité de
base, y compris les mesures suivantes.
2.
Conserver ces instructions
et s’y reporter en cas d’ajouts ou de changements
au profil du système sur rail.
3. Couper le courant électrique avant de faire des
ajouts ou des changements au profil du rail.
4. Seulement pour systèmes de rails série LZR100.
5. Alimentation electrique: 120V, 60Hz, 20A
INSTRUCCIONES DE INSTALACIÓN
MEDIDAS IMPORTANTES DE
SEGURIDAD
1. Antes de conectar el sistema de rieles lea las
instrucciones para instalación
2.
Guarde estas instrucciones
y sigalas cada vez que se hagan adiciones o cam-
bios en la configuracion del sistema.
3. Desconecte el suministro eléctrico antes de hacer
adiciones o canbios en la configuración del
sistema.
4. Para ser utilizado solamente con los sistemas de
riel de la serie LZR 100.
5. Capacidades nominales eléctricas: 120V, 60Hz, 20A
Cooper Lighting
Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269
701166
POLARITY GROOVE
GORGE DE POLARIT
RANURA DE POLARIDAD
POLARITY GROOVE
GORGE DE POLARIT
RANURA DE POLARIDAD
GROUND CONDUCTOR
VIS DE TERRE
CALIBRADOR DE
PELADURA
LOCKING SCREW
VIS DE BLOCAGE
TORNILLO DE SEGURIDAD
DEAD END
BOUT MORT
PUNTA UERTA
LOCKING SCREW
VIS DE BLOCAGE
TORNILLO DE SEGURIDAD
  • Page 1 1

Halo LZR212P Installation guide

Halo
Brand
Halo
Model
LZR212P
Type
Installation guide

Halo LZR212P is a mini track connector designed for use with LZR100 Series track systems. It allows for the connection of two sections of track and provides a secure and reliable electrical connection. The connector is easy to install, requiring only the loosening of a set screw, insertion of the connector into the open ends of the track, and tightening of the lock screws. The ground conductor must be on the same side of the sections of track being joined (polarity groove side).

Here are some of the key features and capabilities of the Halo LZR212P:

  • Easy to install
  • Provides a secure and reliable electrical connection
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents