Cumberland MOHD Double Owner's manual

Brand: Cumberland

Model: MOHD Double

Type: Owner's manual

Date: 01-01-15 PNEG-964

Instructions

1004 East Illinois Street • Assumption, IL 62510 • 1-217-226-4421

PNEG-964

Page 1 of 3

Printed in the U.S.A.

www.gsiag.com CN-315800

MOHD Double Install

Double Shutter Motor Kit Assembly Instructions

Mount Return Spring

1. Drill 1/8" hole 1-1/4" left of each connecting bar in flat edge of frame. (See Figure 1.)

2. Attach the return springs from the 1/8" holes in the frame to the pre-drilled 1/8" holes in the connecting

bars, using an “S” hook on both ends of the return springs. (See Figure 3 on Page 2.)

Mount Assembly

1. Attach motor mount bracket to the back of the motor using four (4) #8-32 x 3/8" THS screws.

(See Figure 2 on Page 2.)

2. Remove motor arm. Install the stop bracket as shown to the top of the motor using four (4)

MS #8-32 x 3/8" THS Screws. (See Figure 4 on Page 3.)

3. Re-install the motor arm onto the shaft and tighten

4. Center the motor mount bracket on the frame and attach to frame and center bar using three (3)

#8-18 x 1/2" self-tapping screws and flat washers. (See Figure 1.)

Figure 1 Complete Assembly

Ref # Description Ref # Description

ADrill 1/8" Hole GMotor

Arm

B Return Spring HLead Chain

CConnecting Bar IStop Bracket

DCenter Bar JMotor Mount Bracket

EFrame KYoke Chain

F Motor

Page 2 of 3 PNEG-964

MOHD Double Install

Mount Assembly (Continued)

Figure 2 Motor Mount Bracket

Yoke Chain Installation

1. Measure 34" down from the top of the frame and drill a 1/8" hole into the flat edge on each side of

the frame. (See Figure 1 on Page 1.)

Figure 3 Side View of Connecting Bar

2. Measure up 13" from the top of the motor and drill a 1/8" hole into the center of the center bar.

(See Figure 1 on Page 1.)

3. Measure down 29" from the top of the frame and drill a 1/8" hole through both connecting bars.

(See Figure 1 on Page 1 and Figure 3.)

4. Attach the yoke chain from the 1/8" holes in frame to 1/8" holes in the connecting bars using “S”

hooks. Then attach chain from connecting bars to the 1/8" hole in the center bar using “S” hooks.

Ref # Description

FMotor

J Motor Mount Bracket

L#8-32 x 3/8" THS Screws

Ref # Description

ADrill 1/8'' hole, 1/8'' in and align

with center of blade trough.

B Connecting Bar

PNEG-964 Page 3 of 3

MOHD Double Install

Lead Chain Installation

1. Connect the lead chain from the center bar to the motor arm using “S” hooks.

(See Figure 1 on Page 1.)

2. Move motor arm counterclockwise to full open position. Adjust blades for full open position by

adjusting lead chain to “S” hook at motor arm. (See Figure 4 and Figure 5.)

Figure 4 Motor Front Figure 5 Full Open Shutter Position

Ref # Description

AMotor

B Motor Arm

CStop Bracket

D Full Open Position

EMotor Mount Bracket

F #8-32 x 3/8" THS Screws

GChain

H Full Open Stop

Cumberland MOHD Double Owner's manual

Cumberland MOHD Double Owner's manual

Cumberland MOHD Double Owner's manual

Related papers

Other documents