Anova L1441-CUST Assembly Instruction

Type
Assembly Instruction

This manual is also suitable for

anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
9/16" Open-end or box-end wrench
1/2" Open-end or box-end wrench
Ratchet with 9/16" socket
Ratchet with 1/2" socket
Level
Assembly Instructions
Latitude
L1440 - Latitude 4' Contour Bench
L1441 - Latitude 6' Contour Bench
L1441-CUST - Latitude 6' Contour Cutom
BENCH COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(1) Contour Seat (2) Bench Legs (2) Cross Braces
(4) 3/8"-16 X 1 1/2"
Hex Head Bolts
(4) 5/16"-18 X 1 1/4"
Hex Head Bolts
(8) 3/8" Flat
Washers
(8) 5/16" Flat
Washers
(4) 3/8"-16
Nylock Nuts
(4) 5/16"-18
Nylock Nuts
ASSEMBLY:
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to nish.
3. Locate the bench legs and contour seat and place them as shown.
NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.
1
4' Contour Bench 6' Contour Bench
The assembly is a two-person operation.
6' Contour Custom Bench
2
3/8"-16 X 1 1/2"
Hex Head Bolt
3/8" Flat Washer
3/8" Flat Washer
3/8"-16 Nylock Nut
4. Mount a bench leg to the contour seat by inserting two 3/8"-16 x 1 1/2" hex
head bolts and two 3/8" at washers through the mounting holes. Place a 3/8"
at washer and a 3/8"-16 nylock nut on the end of each bolt and tighten nger
tight.
Repeat this step on the opposite side of the bench with the remaining bench leg.
5. Mount a cross brace to the contour seat by inserting two 5/16"-18 x 1 1/4" hex
head bolts and two 5/16" at washers through the mounting holes. Place a
5/16" at washer and a 5/16"-18 nylock nut on the end of each bolt and tighten
nger tight.
NOTE: The cross brace is placed on the backside of the bench leg.
Repeat this step on the opposite side of the bench.
Cross Brace
5/16"-18 X 1 1/4"
Hex Head Bolt
5/16" Flat Washer
5/16" Flat Washer
5/16"-18 Nylock Nut
Position the bench upright and tighten all of the hardware
while checking with a level.
Aer two weeks, retighten all of the hardware.
6.
7.
18.92"
37.88"
4 X O.40"
L1440 - 4' Latitude Bench Foot Mount
3
Manufactured in the U.S.
Copyright 2022 ANOV
3/21/2022
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
18.92"
4 X O.40"
L1441 - 6' Latitude Bench Foot Mount
61.75"
Assembly and Replacement Parts
Bench Leg
Cross Brace
Contour Seat
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova L1441-CUST Assembly Instruction

Type
Assembly Instruction
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI