Hobbico FLITEWORK FLWA4130 User manual

Brand: Hobbico

Model: FLITEWORK FLWA4130

Category: Remote controlled toys

Type: User manual

This manual is also suitable for

FLITEWORK T28-Mini

- 1 -

Instruction manual

FLITEWORK T28-Mini / FLWA4130

Version 1.00

Wingspan 650 mm

Length 570 mm

Take off weight 330 g

Radio channels A, E, M

Battery 3s 850 mAh

Fully licensed through the Red Bull GmbH - Austria

Please read the instruction manual carefully and take notice of the safety guidelines.

If the model is given to a third party, always include this instruction manual to the model.

The Flitework Gmbh assumes no liability in case of misprints. Technical amendments reserved.

Distributed by

www.flyingbulls.at

- 2 -

Technical data........................................................1

Introduction............................................................2

General information...............................................2

Environment protection infos.................................2

Safety precautions.................................................3

Recommended accessories...................................3

Additional items required.......................................3

Kit check................................................................3

Content of delivery.................................................4

Installation of rudder and elevator..........................4

Assembling tail unit and fuselage..........................5

Elevator linkage.....................................................5

Installing the receiver.............................................6

Set the control throws............................................6

Adjusting center of gravity......................................6

Spare parts............................................................6

Scale spinner.........................................................6

Check list...............................................................6

Check list...............................................................7

Hobbico service line...............................................7

Flitework contact....................................................8

Introduction

The T-28 Trojan has relieved the AT-6 as a training aircraft and was used by US Navy as prestage for the F-86 Sabre.

The version of the Flying Bulls is a T-28B of the model year 1954. The Flitework T28 mini convinces with stable flight

characteristics and superior speed range. This model has reinforced carbon wing stringers to get it very stable during

speed flight up to 110 mph.

Attention please!

Remote controlled model planes are not a toy! For assembling, flying and servicing such models, you need a high

grade of technical comprehension and liability. Careless assembling and operation may cause personal and material

damage.

Because the Flitework GmbH has no influence on assembly, RC installation, operation and servicing of the flight

device, any liability is rejected under explicit advice to these dangers.

● Read this manual and its safety precautions carefully!

Keep this manual and if you give the model to a third

party, put this manual to the model.

● Take care, that you are familiar with your transmitter

and all electronic components, used in your plane.

● Take care of all safety instructions of tools, which are

you using to assemble this model.

● Only take glues, which are recommended for the

specific materials and which are approved for model

business.

● Before assembling please check all parts of this kit. If

some parts are missing or have a mistake, please call.

● The symbols on the package show you, that the

model and its accessories should not be put to waste.

All electric and electronic parts should be deposed to

places of waste manage-

ment.

● Batteries and accumula-

tors must be removed

from the devices and

should be deposed to the

correct waste manage-

ment organisation. Take

information from your

home town government.

- 3 -

1. Your T-28 Mini should not be considered a toy, but

rather a sophisticated, working model that functions

very much like a full-size airplane. Because of its

performance capabilities, the T-28, if not assembled

and operated correctly, could possibly cause injury to

yourself or spectators and damage to property.

2.You must assemble the model according to the instruc-

tions. Do not alter or modify the model, as doing so

may result in a unsafe or unflyable model. In a few

cases the instructions may differ slightly from the

photos. In those instances the written instructions

should be considered as correct.

3. You must take time to build straight, true and strong.

4. You must use an R/C radio system that is in first-class

condition and a correctly sized engine and compo-

nents (fuel tank, wheels, etc.) throughout the building

process.

5. You must correctly install all R/C and other compo-

nents so that the model operates correctly on the

ground and in the air.

6. You must check the operation of the model before

every flight to insure that all equipment is operating

and that the model has remained structurally sound.

Be sure to check clevises or other connectors often

and replace them if they show any signs of wear or

fatigue.

7. If you are not already an experienced R/C pilot, you

should fly the model only with the help of a competent,

experienced R/C pilot.

8. While this kit has been flight tested to exceed normal

use, if the plane will be used for extremly hight stress

flying, such as racing, or if an engine larger than one

in the recommended range is used, the modeler is

responsible for taking steps to reinforce the hight

stress points and/or substituting hardware more suit-

able for the increased stress.

Flitework quality

We, as the kit manufacturer, provide you with a top quality kit and instructions, but ultimately the

quality and flyability of your finished model depends on how you build it; therefore, we cannot in

any way guarantee the performance of your completed model and no representations are

expressed or implied as to the performance or safety of your completed model.

1 x Lipo battery 3s 850 mAh 25C

Order No.: GPMP0826

1 x Receiver min. 3 Channels

· Hobby knife

· Philips screw driver

· Set of small wrenches

· 5 Min. epoxy glue

· Prop balancing device

Before starting to build, use the Kit Contents list to take an inventory of this kit to make sure it is complete and inspect

the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you

need assistance with assembly, contact Hobbico Product Support.

Service center Revell GmbH

Henschelstr. 20-30, 32257 Bünde, Germany

Tel: +49 52239 65144

Email: [email protected]

- 4 -

1x Fuselage with main wing, mounted motor, prop, spinner, ESC and servos.

1x Fuselage upper part with canopy and pilot figures.

1x Rudder

1x Elevator with preinstalled flap lever.

1x Elevator linkage

1x Scale spinner

1x Multilingual instruction manual

- 5 -

Remove the color from the glueing areas by sanding the

parts carefully. For hidden areas you can use a glass

pencil, which you can get from the stationery store.

If you put the parts together with 5 min. epoxy glue, take

care for a correct alignment. Fix the parts with pins until

the glue is setted.

Attention!!

Never take CA glue for EPO, because this glue causes

damages to this material. Always take epoxy glue.

If you use to much of epoxy glue, the glue is oozing out

between the parts. You can remove this glue, using a

cotton stick.

Before you glue the tail unit to the body, it is very important, to hook in the elevator linkage. Use the third hole, away

from the flap.

Afterward you can glue the complete unit to the fuselage, looking for correct aligment. Take care, that the lower part of

the rudder meets the fuselage at the center. Put also epoxy glue there. Fix the unit with pins until glue has hardened.

Adjust the elevator linkage so, that elevator flap and servo

lever are in neutral position as shown in the picture. The

position of the clevis should be the third hole from oter

side of the servo lever.

Take care, that the prong of the clevis snaps correct to the

opposite side.

Additional you can fix the clevis with a small shrinking

tube, provided in this kit.

- 6 -

Elevator Ailerons

+/- 5mm +/- 7mm

In the following picture you can see a possible placement

of the compnents like receiver and battery. To have no

problem with the CG, you should place the receiver as

backmost as possible.

For connecting the ailerons you can use the included

V-cable.

If you like experimenting with flaps or you like aileron

differentiation, it would be better to connect each aileron

servo to a separate channel.

5cm

The CG is located 5cm behind the joint of fuselage and

main wing. Especially small models require a correct CG

to have good flight performance.

FLWA4131 Motor cowl T28-Mini

FLWA4132 Fuselage upper part with canopy

FLWA4133 Speed spinner

FLWA4134 Brushless motor T28-Mini

FLWA4135 ESC T28-Mini

FLWA4136 Servo T28-Mini

FLWA4137 Prop adapter incl. screws T28-Mini

HCAQ9008 Tuning propeller APC 5 x 5 E

If you prefer more scale look, you can replace the speed

spinner with the provided scale spinner.

During the last few moments of preparation

your mind may be elsewhere anticipating the

excitement of the first flight. Because of this,

you may be more likely to overlook certain

checks and procedures that should be per-

formed before the model is flown. To help

avoid this, a checklist is rovided to make

sure these important areas are no over-

looked. Many are covered in the instruction

manual, so where appropriate, refer to the

manual for complete instructions. Be sure to

check the items off as they are completed

(that's why it's called a check list!).

- 7 -

● 1. Check the C.G. according to the measure-

ments provided in the manual.

● 2. Be certain the battery and receiver are

securely mounted in the fuse. Simply stuffing

them into place with foam rubber is not suffi-

cient.

● 3. Look for a correct position of your receiver

antenna or antennas. The antenna should

not be ´close to other wires inside the fuse-

lage.

● 4. Balance your model laterally as explained

in the instructions.

● 5. Use threadlocking compound to secure

critical fasteners such as the set screws that

hold the wheel axles to the struts, screws

that hold the carburetor arm (if applicable),

screw-lock pushrod connectors, etc.

● 6. Add a drop of oil to the axles so the

wheels will turn freely.

● 7. Make sure all hinges are securely glued in

place.

● 8. Reinforce holes for wood screws with thin

CA where appropriate (servo mounting

screws, cowl mounting screws, etc.).

● 9. Confirm that all controls operate in the

correct direction and the throws are set up

according to the manual.

● 10. Make sure there are silicone retainers on

all the clevises and that all servo arms are

secured to the servos with the screws in-

cluded with your radio.

● 11. Secure connections between servo wires

and Y connectors or servo extensions and

the connection between your battery pack

and the on/off switch with vinyl tape, heat

shrink tubing or special clips suitable for that

purpose.

● 12. Make sure any servo extension cords you

may have used do not interfere with other

systems (servo arms, pushrods, etc.).

● 14. Secure the pressure tap (if used) to the

muffler with high temp RTV silicone, thread

locking compound or J.B.Weld.

● 15. Make sure the fuel lines are connected

and are not kinked.

● 16. Balance your propeller (and spare propel-

lers).

● 17. Tighten the propeller nut and spinner.

● 18. Place your name, address, AMA number

and telephone number on or inside your mod-

el.

● 19. Cycle your receiver battery pack (if nec-

essary) and make sure it is fully charged.

● 20. If you wish to photograph your model, do

so before your first flight.

● 21. Range check your radio when you get to

the flying field.

Service department Revell GmbH

Henschelstr. 20-30, 32257 Bünde, Germany

Tel: +49 52239 65144

Email: [email protected]

- 8 -

Remember to think.

Have a ball!

But always stay in control and fly in

a safe manner.

GOOD LUCK AND

GREAT FLYING!

Flitework GmbH

Geymannstr. 27, 4713 Gallspach, Austria

Tel: +43 664 3231 059

Email: [email protected]

Hobbico FLITEWORK FLWA4130 User manual

Brand: Hobbico

Model: FLITEWORK FLWA4130

Category: Remote controlled toys

Type: User manual

This manual is also suitable for

FLITEWORK T28-Mini

Download PDF

report

Hobbico FLITEWORK FLWA4130 User manual

This manual is also suitable for

Hobbico FLITEWORK FLWA4130 User manual

Related papers

Other documents