Audiovox EM-2202 Installation guide

Brand: Audiovox

Model: EM-2202

Type: Installation guide

This manual is also suitable for

PROTR3M

PROTR4

EM-~O2

INST ALLA TION 'INSTRUCTIONS

CAUTION: DO NOT CLOSE TRUNK UNTIL

INSTALLATION IS COMPLETE AND YOu HAVE

TESTED THE ACTUATOR. (tailure to do so can

result in a locked trunk with no way to unlock it}.

B. Under dash installation. If you are

installing the switch button under the dash you will

need to use the switch bracket and snap ring.

Remove a screw under the dash at your desired

location or use the enclosed self-tappping screw and

install the switch button bracket. Connect the wiring

to the switch button as described In the preceding

paragraph.

s~p 1. Put towel or rag over the latch striker to

pr~vent accidental trunk closure.

STEP 2. Remove existing cable from lock cylinder

an4 latch. On some vehicles this will require drilling

oU~ two pop rivets holding the cable to the lock

cylInder.

STEP 7. Connecting the switch button. Decide first

If you want your switch to have constant power or

ignition activated power. Then taking the blank end

of the red wire you can connect at the fuse box or

splice into an existing wire. Once connected your

switch will be operable upon reconnecting the

positive battery cable.

STEp 3. Install motorized actuator. Using a 8mm

socket install the solenoid on the latch using the

incLuded se'f-tapping screws. (Do not overtighten

screws as this will bind the actuator). Next connect

the actuator cable to the lock cylinder using either

pop rivets or screws.

STEP 8. Test and adjust. With trunk still open have

someone push the switch button while you observe

the actuator. When the switch is activated the

actuator should move. It not. loosen screws holding

the actuator to the latch until the actuator is able to

move freely. If the actuator dId not run when button

was depressed. check your connections or if ignition

activated. make sure key is on. Try again. Next

check the key in the lock cylinder as described in

STEP 3.

sTf.P 4. Route wiring harness. Decide first where

you wish to mount the switch button (glove box or

under dash). Starting at the actuator, plug the black

wire into the actuator and route the wire either

through or along the trunk deck ribbing in the most

direct route to yOUf desired switch button location.

You may have to remove the rear seat. Leave the

black wife loose untIl STEP 9. Using a sheet metal

scr6;w attach the green ground wire to a metal

8U~ce. Without a proper ground your actuator will

not work.

STEP 9. Finish. Remove or JooSGn necessary trim

from switch button along the wiring route to the

solenoid. Tuck the wiring beneath the trim panels

and tighten.

STEP 5. Disconnect positive battery cable .

STEP 6. Install switch button.

A. GIOVQ box instal'ation. It you are installing

your, switch in the glove box, many models have

plugged holes already in the glove box. If your

vehicle is so equipped remove the plug. The hole

may be either 3/4. or 1 " In diameter. If the hole is 1.

diameter you will need to use the optional snap ring

with your switch button. Glove boxes with square

hole$ or without precut holes will require a 314.

diameter hole be cut or an under dash installation

used;. (CAUTION: If you choose to cut a hole

remoVe the glove box insert to prevent damage to

vehicle equipment located behind it). Once your hole

is loc~ted. route the terminals on the black wire and

red wire through and connect them to the switch

button. Push the switch button back into the hole.

PARTI

EM20-988

EM15-216

EM210-107

EM210-109

EM226-123

EM55.148

EM26-104

EM29-309

EM15-214

EM22-102

EM40-110

PARTS ENCLOSED

.Q!Y:. DESCRIPTION

1 Actuator

2 Screws (Actuator)

1 Wiring (Red)

1 Wiring (Black)

1 Tap Connector

1 Snap Ring

1 SwItch Bu"on

1 Switch Bracke'

1 Bracket Screw

1 Cable Tie

1 Instruction Sheet

From. 6fg4

'-.~

REAR WIN"DOW lllATCH RELeASE

INSTALLATION ~STRUCT'ONS

PARTS E"CLOSED:

Qty.

1 Solenoid

2 Machine Screw

2 Washers (Solenoid)

1 E-Clip

1 Washer (Cable)

1 Wire Harness (Red)

1 Wire Harness (Blk.)

1 Tap Connector

1 Snap Ring

Switch Button

SwItch Bracket

Bracket Screw

Cable Tie

InstructIon Sheet

Part

EMD20-987

EMA15-217

EMA7e.242.

EM178-123

EMA78-243

EMB210-107

EM62'0-10e

EMA226-123

EMAS5.'48

EMA26-104

EMC29-309

EMA15-214

EMA22-102

EMA40-102

STEP 5. Inst811 Switch Button.

A. Glov. box lnetallatlon.

If you are installIng your switch In the glo'ie bOx many models

have plugged holeS alreedy in them. If your vehicle is 90

equipped. remo'ie the plug. The hole may be either 3/4. or' II in

diameter If the hole is' .diameter you will need to use the

optional snap ri(\Q. Glove boxes without plugged holes will

require a 3/4" diameter hole be cut (Caution: Remove glove

box insert before drilling Hole). Once your hole is located. route

the connector plugs on tt1e black and red wires through and

connect them to t~e switch button. Push the switch button into

the hole.

8. Under dash Inata'lltlon.

If you are installing the switch button under the dash you will

need to use the switch bracket and snap ring. Remove a screw

under the dash or use tn9 enclosed self-tapping ICfew and

inatall the switch button bracket. Connect the wiring to the

switch button 8S d8scribed in abo"e paragraph.

, STEP 6. Connecting the Swttch Button.

Taking the blank end of the red wire determine If you wish to

connect at the fuse box or splice into an exist\ng w\~ DecIde

lWhether you want your power source to be ignition activated or

lconstant and complete tM connection. Your switch will be

'operable uoon reconn~ing the battery.

STeP ,. Dlaconnect PO8ittv. Battery Cabl.

STEP 2. ; Refnov. Panel From R..r Uftgat.

STEP 3. 1n8t8l1 SolenoId

Figure At below shows the so\enoid instaltation k>oklng through

the ext~r sheet metal. Once you have the inside panel

-,.mcw84 from ~te you wtR MKt have to rernove th8- .

metal cover over the latch mechanism and tn. metal bracket

occupyt~ the tailgate lICCeta hole. Orientate the solenoid

inside the liftgate acc988 aligning me solenoid bracket holes

with the i holes in the liftgate. Using the two maChine screws

with w88hers attach the solenoid to in. liftgat. by inserting the

~ehers through the sheet meial and into the solenoid

bracket ;until fIght. Next attach the solenoId cable to the latch

lever -shown in fIgure B.

STEP 7. T..t .AdJUat

Close rear hatcn and push switch button. If window opens,

move to Step 8. if it does not open and your system is ignition

activated, insure the key is on. It solenoid ~1ick8 but window

does not open check assembly to latch for proper connection. It

solenoid does not click check your power source connection.

STEP 8. Flnleh

Remove or loosen neces8ary trim along the wiring route to the

solenoid. Tuck the wiring beneath the trim P8"8I8 and tighten.

Replace rear trim panel on liftgate. Vour in8'allatlon is

complete.

STEP 4. AouUng WIN H.neaa

Plug one end of black wire into aoleno\d oon~or and route

w'n along 8id8 tr1m pan... to the location where you wish to

in..I' ~f 9w\tch button. Leave wire loose until step 8.

Audiovox EM-2202 Installation guide

Brand: Audiovox

Model: EM-2202

Type: Installation guide

This manual is also suitable for

Download PDF

report

Audiovox EM-2202 Installation guide

This manual is also suitable for

Audiovox EM-2202 Installation guide

Related papers

Other documents