Mazda 2002 626 Specification

Brand: Mazda

Model: 2002 626

Category: Cars

Type: Specification

This manual is also suitable for

CONTENTS

Mazda6

Workshop

Manual

FOREWORD

This manual contains on-vehicle service

and diagnosis for the Mazda6.

For proper repair and maintenance,

a thorough familiarization with this manual

is important, and it should always be kept

in a handy place for quick and easy

reference.

All the contents of this manual, including

drawings and specifications, are the latest

available at the time of printing.

As modifications affecting repair or

maintenance occur, relevant information

supplementary to this volume will be made

available at Mazda dealers. This manual

should be kept up-to-date.

Mazda Motor Corporation reserves

the right to alter the specifications and

contents of this manual without obligation

or advance notice.

may be reproduced or used in any form or

by any means, electronic or

mechanicalincluding photocopying and

recording and the use of any kind of

information storage and retrieval

systemwithout permission in writing.

Mazda Motor Corporation

HIROSHIMA, JAPAN

APPLICATION:

This manual is applicable to vehicles

beginning with the Vehicle Identification

Numbers (VIN), and related materials shown

on the following page.

PRINTED IN The Netherlands, MARCH 2002

17301E02C

Title Section

General Information

Engine

Lubrication System

Cooling System

Fuel and Emission Control Systems

Engine Electrical System

Clutch

Manual Transaxle

Automatic Transaxle

Front and Rear Axles

Steering System

Braking System

Suspension

Body

Body Electrical System

Heater and Air Conditioner Systems

Technical Data

Special Tools

VEHICLE IDENTIFICATION NUMBERS (VIN)

U.K. specs.

JMZ GG12820# 100001

JMZ GG14320# 100001

JMZ GG14820# 100001

JMZ GG12F20# 100001

JMZ GG12F50# 100001

JMZ GG14F20# 100001

JMZ GG14F50# 100001

European (L.H.D.) specs.

JMZ GG1232✻

✻✻

✻# 100001

JMZ GG1282✻

✻✻

✻# 100001

JMZ GG1432✻

✻✻

✻# 100001

JMZ GG1482✻

✻✻

✻# 100001

JMZ GG12F2✻

✻✻

✻# 100001

JMZ GG12F5✻

✻✻

✻# 100001

JMZ GG14F2✻

✻✻

✻# 100001

JMZ GG14F5✻

✻✻

✻# 100001

GCC specs.

JM7 GG32F✻✻

✻✻✻✻

✻✻# 100001

JM7 GG34F✻✻

✻✻✻✻

✻✻# 100001

JM7 GG42F✻✻

✻✻✻✻

✻✻# 100001

JM7 GG44F✻✻

✻✻✻✻

✻✻# 100001

RELATED MATERIALS

Mazda6 Training Manual

(European (L.H.D.), GCC Specs.) . . . . . . . . . . . . . . . . 33591*02C

Engine Workshop Manual L8, LF, L3 . . . . . . . . . . . . . . 17311*02C

Manual Transaxle Workshop Manual

G35MR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17321*02C

Automatic Transaxle Workshop Manual

FN4AEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16231098E

Automatic Transaxle Workshop Manual

Supplement FN4AEL . . . . . . . . . . . . . . . . . . . . . . . . . 17461*02C

Mazda6 Wiring Diagram

(European (L.H.D.), GCC specs.) . . . . . . . . . . . . . . . . 55391*02C

Mazda6 Wirinig Diagram

(U.K. specs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55401*02C

Mazda6 Bodyshop Manual

(European (L.H.D. U.K.), GCC specs.) . . . . . . . . . . . . 33601*02C

* : Indicates the printing location

E: Europe

0: Japan

WARNING

Servicing a vehicle can be dangerous. If you have not received

service-related training, the risks of injury, property damage, and

failure of servicing increase. The recommended servicing procedures

for the vehicle in this workshop manual were developed with

Mazda-trained technicians in mind. This manual may be useful to

non-Mazda trained technicians, but a technician with our

service-related training and experience will be at less risk when

performing service operations. However, all users of this manual are

expected to at least know general safety procedures.

This manual contains "Warnings" and "Cautions" applicable to risks

not normally encountered in a general technician's experience.

They should be followed to reduce the risk of injury and the risk that

improper service or repair may damage the vehicle or render it unsafe.

It is also important to understand that the "Warnings" and "Cautions"

are not exhaustive. It is impossible to warn of all the hazardous

consequences that might result from failure to follow the procedures.

The procedures recommended and described in this manual are

effective methods of performing service and repair. Some require tools

specifically designed for a specific purpose. Persons using procedures

and tools which are not recommended by Mazda Motor Corporation

must satisfy themselves thoroughly that neither personal safety nor

safety of the vehicle will be jeopardized.

The contents of this manual, including drawings and specifications, are

the latest available at the time of printing, and Mazda Motor Corporation

reserves the right to change the vehicle designs and alter the contents

of this manual without notice and without incurring obligation.

Parts should be replaced with genuine Mazda replacement parts or

with parts which match the quality of genuine Mazda replacement

parts. Persons using replacement parts of lesser quality than that of

genuine Mazda replacement parts must satisfy themselves thoroughly

that neither personal safety nor safety of the vehicle will be

jeopardized.

Mazda Motor Corporation is not responsible for any problems which

may arise from the use of this manual. The cause of such problems

includes but is not limited to insufficient service-related training, use of

improper tools, use of replacement parts of lesser quality than that of

genuine Mazda replacement parts, or not being aware of any revision

of this manual.

GI1

GIGENERAL INFORMATION

HOW TO USE THIS MANUAL ..............................GI-2

RANGE OF TOPICS...........................................GI-2

SERVICE PROCEDURE ....................................GI-2

SYMBOLS...........................................................GI-4

ADVISORY MESSAGES ....................................GI-4

TROUBLESHOOTING PROCEDURE................GI-5

UNITS ..................................................................GI-11

UNITS ...............................................................GI-11

FUNDAMENTAL PROCEDURES .......................GI-12

PROTECTION OF VEHICLE ............................GI-12

PREPARATION OF TOOLS AND

MEASURING EQUIPMENT...........................GI-12

SPECIAL SERVICE TOOLS.............................GI-12

OIL LEAKAGE INSPECTION ...........................GI-12

DISCONNECTION OF THE NEGATIVE

BATTERY CABLE..........................................GI-13

REMOVAL OF PARTS .....................................GI-13

DISASSEMBLY.................................................GI-13

INSPECTION DURING REMOVAL,

DISASSEMBLY..............................................GI-14

ARRANGEMENT OF PARTS ...........................GI-14

CLEANING OF PARTS.....................................GI-14

REASSEMBLY..................................................GI-14

ADJUSTMENT..................................................GI-15

RUBBER PARTS AND TUBING .......................GI-15

HOSE CLAMPS ................................................GI-16

TORQUE FORMULAS......................................GI-16

VISE..................................................................GI-16

DYNAMOMETER..............................................GI-17

SST ...................................................................GI-17

INSTALLATION OF RADIO SYSTEM ............... GI-17

INSTALLATION OF RADIO SYSTEM ............. GI-17

ELECTRICAL SYSTEM...................................... GI-18

ELECTRICAL PARTS ...................................... GI-18

CONNECTORS................................................ GI-18

ELECTRICAL TROUBLESHOOTING

TOOLS .......................................................... GI-22

PRECAUTIONS BEFORE WELDING.............. GI-23

JACKING POSITIONS ,VEHICLE LIFT

(2 SUPPORTS),SAFETY STANDS

(RIGID RACK) POSITIONS................................ GI-24

JACKING POSITIONS, VEHICLE LIFT

(2 SUPPORTS) AND SAFETY STAND

(RIGID RACK) POSITIONS .......................... GI-24

TOWING ............................................................. GI-26

TOWING .......................................................... GI-26

TOWING HOOKS ............................................ GI-26

IDENTIFICATION NUMBER LOCATIONS ........ GI-28

VEHICLE IDENTIFICATION

NUMBER(VIN) .............................................. GI-28

ENGINE IDENTIFICATION NUMBER ............. GI-28

NEW STANDARDS ............................................ GI-29

NEW STANDARDS.......................................... GI-29

ABBREVIATIONS .............................................. GI-31

ABBREVIATIONS ............................................ GI-31

PRE-DELIVERY INSPECTION........................... GI-32

PRE-DELIVERY INSPECTION........................ GI-32

SCHEDULED MAINTENANCE .......................... GI-33

SCHEDULED MAINTENANCE TABLE ........... GI-33

GI2

HOW TO USE THIS MANUAL

RANGE OF TOPICS

A6E201000001W01

• This manual contains procedures for performing all required service operations. The procedures are divided

into the following five basic operations:

 Removal/Installation

 Disassembly/Assembly

Replacement

 Inspection

 Adjustment

• Simple operations which can be performed easily just by looking at the vehicle (i.e., removal/installation of

parts, jacking, vehicle lifting, cleaning of parts and visual inspection) have been omitted.

End Of Sie

SERVICE PROCEDURE

A6E201000001W02

Inspection, adjustment

• Inspection and adjustment procedures are divided into steps. Important points regarding the location and

contents of the procedures are explained in detail and shown in the illustrations.

HOW TO USE THIS MANUAL

XME2010001

HOW TO USE THIS MANUAL

GI3

Repair procedure

1. Most repair operations begin with an overview illustration. It identifies the components, shows how the parts fit

together and describes visual part inspection. However, only removal/installation procedures that need to be

performed methodically have written instructions.

2. Expendable parts, tightening torques and symbols for oil, grease, and sealant are shown in the overview

illustration. In addition, symbols indicating parts requiring the use of special service tools or equivalent are also

shown.

3. Procedure steps are numbered and the part that is the main point of that procedure is shown in the illustration

with the corresponding number. Occasionally, there are important points or additional information concerning a

procedure. Refer to this information when servicing the related part.

End Of Sie

XME2010010

GI4

HOW TO USE THIS MANUAL

SYMBOLS

A6E201000001W03

• There are eight symbols indicating oil, grease, fluids, sealant, and SST or equivalent use. These symbols show

application points or use of these materials during service.

End Of Sie

ADVISORY MESSAGES

A6E201000001W04

• You'll find several Warnings, Cautions, Notes, Specifications and Upper and Lower Limits in this manual.

Warning

• A Warning indicates a situation in which serious injury or death could result if the warning is ignored.

Caution

• A Caution indicates a situation in which damage to the vehicle or parts could result if the caution is ignored.

Note

• A Note provides added information that will help you to complete a particular procedure.

Specification

• The values indicate the allowable range when performing inspections or adjustments.

Upper and lower limits

• The values indicate the upper and lower limits that must not be exceeded when performing inspections or

adjustments.

End Of Sie

Symbol Meaning Kind

Apply oil

New appropriate

engine oil or gear

oil

Apply brake fluid

New appropriate

brake fluid

Apply automatic

transaxle/

transmission fluid

New appropriate

automatic

transaxle/

transmission fluid

Apply grease

Appropriate

grease

Apply sealant

Appropriate

sealant

Apply petroleum

jelly

Appropriate

petroleum jelly

Replace part

O-ring, gasket,

etc.

Use SST or

equivalent

Appropriate tools

HOW TO USE THIS MANUAL

GI5

TROUBLESHOOTING PROCEDURE

A6E201000001W05

Basic flow of troubleshooting

DTC troubleshooting flow (on-board diagnostic)

• Diagnostic trouble codes (DTCs) are important hints for repairing malfunctions that are difficult to simulate.

Perform the specific DTC diagnostic inspection to quickly and accurately diagnose the malfunction.

• The on-board diagnostic function is used during inspection. When a DTC is shown specifying the cause of a

malfunction, continue the diagnostic inspection according to the items indicated by the on-board diagnostic

function.

Diagnostic index

• The diagnostic index lists the symptoms of specific malfunctions. Select the symptoms related or most closely

relating to the malfunction.

Quick diagnosis chart (If mentioned)

• The quick diagnosis chart lists diagnosis and inspection procedures to be performed specifically relating to the

cause of the malfunction.

Symptom troubleshooting

• Symptom troubleshooting quickly determines the location of the malfunction according to symptom type.

XME2010002

GI6

HOW TO USE THIS MANUAL

Procedures for Use

Using the basic inspection (section K)

• Perform the basic inspection procedure before symptom troubleshooting.

• Perform each step in the order shown.

• The reference column lists the location of the detailed procedure for each basic inspection.

• Although inspections and adjustments are performed according to the reference column procedures, if the

cause of the malfunction is discovered during basic inspection, continue the procedures as indicated in the

remarks column.

XME2010003

HOW TO USE THIS MANUAL

GI7

Using the DTC troubleshooting flow

• DTC troubleshooting flow shows diagnostic procedures, inspection methods, and proper action to take for each

DTC.

XME2010004

GI8

HOW TO USE THIS MANUAL

Using the diagnosis index

• The symptoms of the malfunctions are listed in the diagnostic index for symptom troubleshooting.

• The exact malfunction symptoms can be selected by following the index.

XME2010006

HOW TO USE THIS MANUAL

GI9

Using the quick diagnosis chart

• The chart lists the relation between the symptom and the cause of the malfunction.

• The chart is effective in quickly narrowing down the relation between symptom and cause of the malfunction. It

also specifies the area of the common cause when multiple malfunction symptoms occur.

• The appropriate diagnostic inspection relating to malfunction cause as specified by the symptoms can be

selected by looking down the diagnostic inspection column of the chart.

XME2010011

GI10

HOW TO USE THIS MANUAL

Using the symptom troubleshooting

• Symptom troubleshooting shows diagnostic procedures, inspection methods, and proper action to take for

each trouble symptom.

End Of Sie

XME2010007

UNITS

GI11

UNITS

A6E201200002W01

Conversion to SI Units (Système International d'Unités)

• All numerical values in this manual are based on SI units. Numbers shown in conventional units are converted

from these values.

Rounding Off

• Converted values are rounded off to the same number of places as the SI unit value. For example, if the SI unit

value is 17.2 and the value after conversion is 37.84, the converted value will be rounded off to 37.8.

Upper and Lower Limits

• When the data indicates upper and lower limits, the converted values are rounded down if the SI unit value is

an upper limit and rounded up if the SI unit value is a lower limit. Therefore, converted values for the same SI

unit value may differ after conversion. For example, consider 2.7 kgf/cm

in the following specifications:

210260 kPa {2.12.7 kgf/cm

, 3038 psi}

270310 kPa {2.73.2 kgf/cm

, 3945 psi}

• The actual converted values for 2.7 kgf/cm

are 264 kPa and 38.4 psi. In the first specification, 2.7 is used as

an upper limit, so the converted values are rounded down to 260 and 38. In the second specification, 2.7 is

used as a lower limit, so the converted values are rounded up to 270 and 39.

End Of Sie

UNITS

Electrical current A (ampere)

Electric power W (watt)

Electric resistance Ω (ohm)

Electric voltage V (volt)

Length

mm (millimeter)

in (inch)

Negative pressure

kPa (kilo pascal)

mmHg (millimeters of mercury)

inHg (inches of mercury)

Positive pressure

kPa (kilo pascal)

kgf/cm

(kilogram force per square

centimeter)

psi (pounds per square inch)

Torque

N·m (Newton meter)

kgf·m (kilogram force meter)

kgf·cm (kilogram force centimeter)

ft·lbf (foot pound force)

in·lbf (inch pound force)

Volume

L (liter)

US qt (U.S. quart)

Imp qt (Imperial quart)

ml (milliliter)

cc (cubic centimeter)

cu in (cubic inch)

fl oz (fluid ounce)

Weight

g (gram)

oz (ounce)

GI12

FUNDAMENTAL PROCEDURES

PROTECTION OF VEHICLE

A6E201400004W01

• Always be sure to cover fenders, seats and floor

areas before starting work.

End Of Sie

PREPARATION OF TOOLS AND MEASURING EQUIPMENT

A6E201400004W02

• Be sure that all necessary tools and measuring

equipment are available before starting any work.

End Of Sie

SPECIAL SERVICE TOOLS

A6E201400004W03

• Use special service tools or equivalent when they

are required.

End Of Sie

OIL LEAKAGE INSPECTION

A6E201400004W04

• Use either of the following procedures to identify the type of oil that is leaking:

Using UV Light (Black Light)

1. Remove on the engine or transaxle.

Note

• Referring to the fluorescent dye instruction manual, mix the specified amount of dye into the engine oil or

ATF (or transaxle oil).

2. Pour the fluorescent dye into the engine oil or ATF (or transaxle oil).

3. Allow the engine to run for 30 minutes.

4. Inspect for dye leakage by irradiating with UV light (black light), and identify the type of oil that is leaking.

FUNDAMENTAL PROCEDURES

X3U000WAG

X3U000WAH

X3U000WAJ

FUNDAMENTAL PROCEDURES

GI13

5. If no dye leakage is found, allow the engine to run for another 30 minutes or drive the vehicle then reinspect.

6. Find where the oil is leaking from, then make necessary repairs.

Note

• To determine whether it is necessary to replace the oil after adding the fluorescent dye, refer to the

fluorescent dye instruction manual.

Not Using UV Light (Black Light)

1. Gather some of the leaking oil using an absorbent white tissue.

2. Take samples of engine oil and ATF (or transaxle oil), both from the dipstick, and place them next to the leaked

oil already gathered on the tissue.

3. Compare the appearance and smell, and identify

the type of oil that is leaking.

4. Remove any oil on the engine or transaxle/

transmission.

5. Allow the engine to run for 30 minutes.

6. Check the area where the oil is leaking, then

make necessary repairs.

End Of Sie

DISCONNECTION OF THE NEGATIVE BATTERY CABLE

A6E201400004W05

• Before beginning any work, turn the ignition switch to LOCK position, then disconnect the negative battery

cable and wait for more than 1 minute to allow the backup power supply of the SAS unit to deplete its stored

power. Disconnecting the battery cable will delete the memories of the clock, audio, and DTCs, etc. Therefore,

it is necessary to verify those memories before disconnecting the cable.

• If the battery had been disconnected during vehicle maintenance or for other reasons, the window will not fully

close automatically.Carry out the power window main switch initial setting. (See S23 INITIAL SETTING.)

End Of Sie

REMOVAL OF PARTS

A6E201400004W06

• While correcting a problem, also try to determine

its cause. Begin work only after first learning

which parts and subassemblies must be removed

and disassembled for replacement or repair. After

removing the part, plug all holes and ports to

prevent foreign material from entering.

End Of Sie

DISASSEMBLY

A6E201400004W07

• If the disassembly procedure is complex,

requiring many parts to be disassembled, all parts

should be marked in a place that will not affect

their performance or external appearance and

identified so that reassembly can be performed

easily and efficiently.

End Of Sie

XME2014003

X3U000WA

X3U000WAL

GI14

FUNDAMENTAL PROCEDURES

INSPECTION DURING REMOVAL, DISASSEMBLY

A6E201400004W08

• When removed, each part should be carefully

inspected for malfunction, deformation, damage,

and other problems.

End Of Sie

ARRANGEMENT OF PARTS

A6E201400004W09

• All disassembled parts should be carefully

arranged for reassembly.

• Be sure to separate or otherwise identify the parts

to be replaced from those that will be reused.

End Of Sie

CLEANING OF PARTS

A6E201400004W10

• All parts to be reused should be carefully and

thoroughly cleaned in the appropriate method.

Warning

•

••

• Using compressed air can cause dirt and

other particles to fly out causing injury to

the eyes. Wear protective eye wear

whenever using compressed air.

End Of Sie

REASSEMBLY

A6E201400004W11

• Standard values, such as torques and certain

adjustments, must be strictly observed in the

reassembly of all parts.

X3U000WAM

X3U000WAN

WGIWXX0030J

WGIWXX0031J

FUNDAMENTAL PROCEDURES

GI15

• If removed, these parts should be replaced with new ones:

 Oil seals

Gaskets

 O-rings

 Lockwashers

 Cotter pins

 Nylon nuts

• Depending on location:

 Sealant and gaskets, or both, should be applied to specified locations. When sealant is applied, parts

should be installed before sealant hardens to prevent leakage.

 Oil should be applied to the moving components of parts.

 Specified oil or grease should be applied at the prescribed locations (such as oil seals) before reassembly.

End Of Sie

ADJUSTMENT

A6E201400004W12

• Use suitable gauges and/or testers when making

adjustments.

End Of Sie

RUBBER PARTS AND TUBING

A6E201400004W13

• Prevent gasoline or oil from getting on rubber

parts or tubing.

End Of Sie

WGIWXX0032J

X3U000WAS

WGIWXX0034E

GI16

FUNDAMENTAL PROCEDURES

HOSE CLAMPS

A6E201400004W14

• When reinstalling, position the hose clamp in the

original location on the hose and squeeze the

clamp lightly with large pliers to ensure a good fit.

End Of Sie

TORQUE FORMULAS

A6E201400004W19

• When using a torque wrench-SST or equivalent

combination, the written torque must be

recalculated due to the extra length that the SST

or equivalent adds to the torque wrench.

Recalculate the torque using the following

formulas. Choose the formula that applies to you.

A : The length of the SST past the torque wrench drive

L : The length of the torque wrench

End Of Sie

VISE

A6E201400004W16

• When using a vise, put protective plates in the jaws of the vise to prevent damage to parts.

End Of Sie

WGIWXX0035J

Torque Unit Formula

N·m N·m × [L/(L+A)]

kgf·m kgf·m × [L/(L+A)]

kgf·cm kgf·cm × [L/(L+A)]

ft·lbf ft·lbf × [L/(L+A)]

in·lbf in·lbf × [L/(L+A)]

WGIWXX0036E

X3U000WAW

FUNDAMENTAL PROCEDURES, INSTALLATION OF RADIO SYSTEM

GI17

DYNAMOMETER

A6E201400004W17

• When inspecting and servicing the power train on the dynamometer or speed meter tester, pay attention to the

following:

 Place a fan, preferably a vehicle-speed proportional type, in front of the vehicle.

 Make sure the vehicle is in a facility with an exhaust gas ventilation system.

 Since the rear bumper might deform from the heat, cool the rear with a fan. (Surface of the bumper must be

below 70 degrees.)

 Keep the area around the vehicle uncluttered so that heat does not build up.

 Watch the water temperature gauge and dont overheat the engine.

 Avoid added load to the engine and maintain normal driving conditions as much as possible.

Note

• When only the front wheels are being rotated on the dynamometer, the ABS warning light could illuminate.

If the ABS warning light illuminates, turn the ignition switch to the LOCK position, then turn it back to the

ON position, run the vehicle at 10km/h and check that the ABS warning light goes off. (In this case, a DTC

will be stored in the memory. To delete this data from the memory, follow the procedure for deleting DTCs

(ABS) from memory.) (See P6 PRECAUTION (BRAKES) ) to turn off the warning light.)

End Of Sie

SST

A6E201400004W18

• Some Ford SST or equivalent are used as SSTs necessary for engine repair. Note that these SSTs are

marked with Ford SST numbers.

• Note that a Ford SST number is written together with a corresponding Mazda SST number as shown below.

Example (section ST)

Example (except section ST)

End Of Sie

INSTALLATION OF RADIO SYSTEM

A6E201600005W01

If a radio system is installed improperly or if a high-powered type is used, the CIS and other systems may be

affected. When the vehicle is to be equipped with a radio, observe the following precautions:

• Install the antenna at the farthest point from control modules.

• Install the antenna feeder as far as possible from the control module harnesses.

• Ensure that the antenna and feeder are properly adjusted.

• Do not install a high-powered radio system.

End Of Sie

XME2014002

XME2014001

INSTALLATION OF RADIO SYSTEM

Page is loading ...

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187

Mazda 2002 626 Specification

Brand: Mazda

Model: 2002 626

Category: Cars

Type: Specification

This manual is also suitable for

Download PDF

report

Mazda 2002 626 Specification

This manual is also suitable for

Mazda 2002 626 Specification

Related papers

Other documents