Page is loading ...
User's Guide
PIR Observation Camera
SMM-PIRCAMBW
SMM-PIRCAM
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 1
1. Make sure that the cable is plugged in securely
before using. (A loose connection may result in
fire.)
2. When installing the camera on a wall or ceiling, mount it
safely and securely. (A falling camera may cause personal
injury.)
3. Do not place conductive objects (e.g., screwdrivers, coins,
and metal things) or containers filled with water on top of the
camera. (Serious injury may result from fire, electric shock, or
falling objects.)
4. Do not install in a sooty, dusty, or humid location. (Doing so
may cause fire or electric shock.)
5. If any unusual smells or smoke come from the unit, stop using
the product. In such case, immediately disconnect the power
source and contact the service center. (Continued use in such
a condition may cause fire or electric shock.)
32
Important Safety Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE REAR COVER. NO USER
SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present
inside. It is dangerous to make any kind of
contact with any inside part of this product.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
6. If this product fails to operate normally,
contact the store of purchase or your nearest
service center. Never disassemble or modify
this product in any way. (The manufacturer is
not liable for any damage resulting from unauthorized
disassembly or repairs.)
7. When cleaning, do not spray water directly onto parts of the
product. (Doing so may cause fire or electric shock.) Wipe
the surface with a dry cloth. Never use detergents or
chemical cleaners on the product, as this may result in
discoloration of surface or cause damage to the finish.
1. Do not drop objects on the product or apply strong shock to
it. Keep away from a location subject to excessive vibration
or magnetic interference.
2. Do not install in a location subject to high temperature (over
50°C /122°F), low temperature (below -10°C /14°F), or high
humidity. (Doing so may cause fire or electric shock).
3. Avoid a location which is exposed to direct sunlight, or near
heat sources such as heaters or radiators.
(Neglecting to do so may result in a risk of fire).
4. If you want to relocate the already installed product, be sure
to turn off the power and then move or reinstall it.
5. Install in a well - ventilated location.
6. Remove the power plug from the outlet when there is a
lightning storm.
(Neglecting to do so may cause fire or damage to the
product.)
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 2
54
Overview
Number of CCD pixels
PIR Observation Camera is the monitoring cam-
era incorporated with the recent CCD that
provides the best monitoring function in connec-
tion with the CCTV system equipment.
✔
SCC-PIRCAMBW : 270,000 pixels B/W
✔
SCC-PIRCAM : 270,000 pixels Color
Power supply
✔
DC 12V From Monitor (RJ-11 Jack)
✔
DC 12V (Backup Supply) for PIR (2-Pin
Terminal)
Automatic function and
special function
✔
ATW (SMM-PIRCAM only)
✔
ELC(Electronic shutter iris)
✔
Built-in Mic/Speaker
✔
Built-in PIR Sensor
✔
PIR Sensor Relay Output (N.C. 350V/130mA)
Kit Model
✔
SMM-PIRCAM : SMM-15FDQ/21FDQ, SSC-
17TQ only
✔
SMM-PIRCAMBW : SSC-12P only
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 4
76
3
5
4
1
2
<Top> <Bottom>
① Lens
It has a focal length of 3.8mm and makes it
possible for you to observe a relatively wide
area.
➁ Speaker
It outputs the sound signal which was
transfered from the monitor.
➂ Fresnel Lens
An infrared focusing lens for increasing the
sensitivity of the built-in PIR sensor.
<Sensor Detection Angle & Area>
1> Vertical Detection Line
Part Names and
Function
• Please consider the horizontal detection area
and the vertical detection line when choosing
an installation site.
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 6
98
2> Horizontal Detection Area ➃ 6-pin modular jack
Used to connect the camera to the monitor.
PIN NUMBER
!
@
#
$
%
^
SPEC
SPEAKER(HOT)
VIDEO_OUT
GND
SPEAKER(COLD)
AUDIO_OUT/ALARM_OUT
12V DC
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 8
1110
⑤ 5-Pin Terminal Block
A terminal block for supplying backup power
for the PIR sensor operation during power
outages and for transmitting the relay signals
to external devices during the PIR sensor
operation.
5 4 3 2
1
86
7
9
<Inside>
➅ Function Switch
A function switch for the PIR sensor operation.
PIN
!
@
#
$
%
SPEC
Power Input DC 12 Volts
(Back Up) Ground
Not Used
Relay Output COM
(350V 130mA) N.C
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 10
1312
⑦ PIR Sensor
A thermal heat sensor that detects infrared
radiation projected by warm objects.
⑧ Microphone
Capable of picking up all sound in the vicinity
of the camera location and transmitting to the
monitor.
⑨ Electronic Relay
Output power is 350V/130mA.
ON
OFF
! @ # $
• Check to see if the following parts are included
in the purchased package.
Screws
(BH M3 x 30), HUD 5
User's guide
PIR CAMERA
Installation
Check what is inside the
package
PIN
!
@
#
$
Function
Sensor Sensitivity
On, On : Low
On, Off : Normal
Off, On : Normal
Off, Off : High
Alarm LED On/Off (Sensor On)
Sensor On/Off
CABLE
(Camera KIT Option)
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 12
1514
1. Users should not disassemble the camera
from the front direction.
2. Always handle the camera with care. Please
do not apply a shock or vibration as much
as possible and take cautions not to cause
damage or make a scratch on the camera
due to careless storage.
3. Please do not install the camera with the
rainy place or highly humid areas. And do
not operate the camera in the wet place.
4. Do not clean the camera body with the
strong abrasives or soaps. When the
camera becomes dirty, clean it with the dry
rugs. Especially, make sure to use the dedi
cated rugs for lens to clean the dome cover.
5. Please select the camera in the cool area
that is not exposed to the direct sunlight. If
you do, it can cause bad effects on the
product.
1. Do not install directly towards rising or
setting sun. Can cause burn or damage to
internal options.
2. Do not limit desired detection zone by inter
ference of curtains, screens, potted plants,
etc.
3. Also, do not locate it in front of source of
water/oil vapors. Avoid placement of heat
source inside detection zone
4. Do not install outdoors.
Notes on installation and
usage
Camera installation Hints
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 14
1716
INSTALLING THE PIR CAMERA
1. Choose an installation site that can suffi-
ciently support 5 times the weight of the
equipments to be installed.
2. Remove the screw (BH M2.6) at the bottom
of the main unit by turning it counterclock
wise, and then lift the assy-case front as you
push it upward to detach it from the case-
rear.
(❊ Do not apply excessive force, as doing
so may damage the inside assembly.❊)
3. Place the case-rear over the installation site
and mark screw holes with a pencil (indicat-
ed by the circles in the illustration). Drill a
pilot hole for each pencil mark (5mm in
diameter and at least 35mm in depth), and
then fully insert the supplied plastic anchors
(HUD 5) into them.
Screw
(BH M3 x 30)
Assy-case front
Screw (BH M2.6)
CASE-REAR
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 16
1918
4. Connect the Camera connector(RJ-11) cable
to the case-rear as well as the cable to be
connected to the terminal.
5. Align the two holes of the case-rear to the
holes of the plastic anchors, and then fasten
the screw-tappings (BH M3 X 30).
SCREW-TAPPING
G(BH M3 x 30)
SCREW-TAPPING
G(BH M3 x 30)
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 18
2120
6. Adjust the direction of the lens.
1) Use the cross (+) screw driver to turn
the screw (indicated by the arrow in the
illustration) counterclockwise slightly.
The lens body will move.
2) Tilt the lens body down about 10° from
the horizontal, and then turn the screw
clock wise to fasten it.
Screw
(HB M4 x L8)
7. Assemble the assy-case front onto the case-
rear as shown in the illustration. Fasten the
assy-case front to the case-rear with the
screw (BH M2.6) you removed earlier.
CASE-REAR
Screw (BH M2.6) ASSY-CASE
FRONT
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 20
2322
1. Choose an installation site that can suffi
ciently support 5 times the weight of the
equipments to be installed.
2. Place the mount-corner to the corner to
which you want to install the camera and
mark screw holes with a pencil (indicated by
the blue circles in the illustration). Drill a pilot
hole for each pencil mark (5mm in diameter
and at least 35mm in depth), and then fully
insert the supplied plastic anchors (HUD 5)
into them.
3. Install the mount-corner by aligning the four
holes of the mount-corner to the holes of the
plastic anchors, and then fastening the
screw-tappings (BH M3 X 30).
Installing the Camera
using the Mount-Corner
SCREW-
TAPPING
(BH M3 x 30)
SCREW-
TAPPING
(BH M3 x 30)
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 22
2524
4. Remove the screw (BH M2.6) at the bottom
of the main unit by turning it counterclockwise,
and then lift the assy-case front as you push it
upward to detach it from the case-rear.
(❊Do not apply excessive force, as doing so
may damage the inside assembly.❊ )
5. Connecting Cables
1) Connecting the cables to the case-rear.
Connect the RJ-11 cable to the RJ-11
connector on the case-rear and connect the
camera cable to the cable terminal on the on
the case-rear.
Assy-case front
Screw (BH M2.6)
CASE-REAR
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 24
2726
2) Passing the cables through the hole on
the mount-corner.
Pass the cables through the hole on the
mount-cornder as shown in the right picture
below.
6. Assemble the case-rear onto the mount-
corner by aligning the two holes of the case-
rear to the protrusions of the mount-corner
(indicated by the blue circles in the
illustration) and fastening the screw-tappings
(PH M3 X 16).
SCREW-TAPPING
(PH M3 x 16)
SCREW-TAPPING
(PH M3 x 16)
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 26
2928
7. Adjust the direction of the lens.
1) Use the cross (+) screw driver to turn
the screw (indicated by the arrow in the
illustration) counterclockwise slightly.
The lens body will move.
2) Tilt the lens body down about 10° from
the horizontal, and then turn the screw
clockwise to fasten it.
8. Assemble the assy-case front onto the case-
rear as shown in the illustration. Fasten the
assy-case front to the case-rear with the
screw (BH M2.6) you removed earlier.
Screw
CASE-REAR
Screw (BH M2.6) ASSY-CASE
FRONT
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 28
3130
Cable connection
• Connect the camera cable to the camera cable
jack on the camera,then connect,and the
other end of the cable to the monitor's channel
input jack.
Example:
• Connect the alarm box to the terminal block,
which is located at the bottom of the camera.
Model Name SMM-PIRCAM, SMM-PIRCAMBW
Broadcast Syatem SMM-PIRCAM : NTSC Standard
SMM-PIRCAMBW : EIA Standard
Imaging Device SMM-PIRCAM : 1/4" Color IT CCD
SMM-PIRCAMBW : 1/3" B/W IT CCD
Effective Pixels 537(H) X 505(V)
Synchronization Internal
Resolution SMM-PIRCAM : 330TV Lines(H),
350TV Lines(V)
SMM-PIRCAMBW : 380TV Lines(H),
350TV Lines(V)
Signal Output VBS 1.0 Vp-p (75 ohms composite)
S/N Ratio
≤ 48dB
Minimum Object SMM-PIRCAM : 2 lux (F2.0, 50IRE)
Illumination SMM-PIRCAMBW : 0.2lux (F2.0, 50IRE)
Gamma Correction 0.45
Lens Focal Length = 3.8 mm, F Number = 2.0
Auto Exposure Electronic Shutter Iris
Caractéristiques
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 30
32
Mounting Height : 1.5m to 3m(5ft to 10ft)
Warm-Up Period : Max. 50 seconds
Spectral Response : 5 to 14 um
Sensitivity : 4860(V/W)
PIR Sensor Detectivity : 1.5 X 10
3
Cm Hz
1/2
/W
Sensor : Off/On
Alarm LED : Off/On ( 0.3~2 sec)
Alarm Output : NC (350V/130mA)
Audio -40 dB Condenser Microphone Inclusion
I/O Connectors Modular Jack (RJ-11)
Operating Temperature -10 to +50°C
Power Source DC 12V (Camera & Sensor from Monitor)
DC 12V (External Power Supplier)
Power Consumption Approx. 2W
Dimensions 40(W) x 69.5(H) x 115(L) mm
Weight About 200g
Part No.: AB68-00421A
Printed in Korea
00421A SMM-PIRCAM-ENG 10/7/03 9:22 AM Page 32
/
