12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
RV814 SERIES PULLOUT WASTE CONTAINER
TOOLS REQUIRED:
15 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
Clean with a damp
cloth and wipe parts
dry.
I-RV814-0117
Parts List
No. Description Qty
1 Frame 1
2 Slide 2
3 Upright 2
4 Floor Screws 4
5 Machine Screws 4
6 Waste Container 1
1
3
4 5
6
2
#2
#2
Determine the position you
would like to install your waste
container by making sure that
no obstruction will interfere
with the unit (See Fig 1).
NOTE: If the current
conguration is not desired
then proceed to step 6 to
install the rotated version
Place the frame into the
cabinet and center the frame
to the center of the cabinet
opening (See Fig 2). The frame
should be at least 1/2” from
the opening to ensure the
cabinet door will be able to
fully close. For inset doors, add
the thickness of the door to
the 1/2” recommendation.
Mark through the 4 horizontally
slotted holes with a pencil
(See Fig 3).
Attach the 4 oor screws using
the hole locations marked in
Step 3.
Remove Wire ties from frame.
NOTE: At this time, skip to
Step 11 and proceed with
your installation.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
DETERMINE YOUR
APPLICATION
FIGURE 1
FIGURE 2
FIGURE 3
CURRENT CONFIGURATION
1/2”
ROTATED VERSION
#2
Rotate the inner bracket piece
90º (See Fig 7A) as well as ip
it upside down (See Fig 7B).
Reattach the frame with the
same 4 machine screws you
removed in Step 6. Refer to
Figure 7C for the new screw
locations.
Remove the wire ties from
the frame. Locate the frame
support machine screws on
both sides of the frame and
remove them (See Fig 6).
Place the frame into the
cabinet and center the frame
to the center of the cabinet
opening (See Fig 8). The frame
should be at least 1/2” from
the opening to ensure the
cabinet door will be able to
fully close. For inset doors, add
the thickness of the door to
the 1/2” recommendation.
Mark through the 4 horizontally
slotted holes with a pencil
(See Fig 9).
attach the 4 oor screws using
the hole locations marked in
step 9.
STEP 6
STEP 8
STEP 9
STEP 10
INSTALLING THE
ROTATED VERSION
#2
#2
FIGURE 9
FIGURE 6
FIGURE 7A
FIGURE 7B
FIGURE 7C
FIGURE 8
SCREW
LOCATIONS
SCREW
LOCATIONS
SCREW
LOCATIONS
ROTATE 90º
FLIP UPSIDE
DOWN
SCREW LOCATIONS
CENTER OF CABINET
1/2”
STEP 7
#2
Insert both uprights into their
corresponding slots from the
interior side of the frame rst
as shown in Figure 11.
STEP 11
INSTALLING THE
UPRIGHTS
FIGURE 11
Place your waste container in
between the uprights.
STEP 12
PLACE YOUR WASTE
CONTAINER
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
INSTALLATION INSTRUCTIONS: RV814 SERIES PULLOUT WASTE CONTAINER
Page is loading ...
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Rev-A-Shelf RV-814PB Mode d'emploi
- español: Rev-A-Shelf RV-814PB Guía del usuario
Related papers
-
Rev-A-Shelf 53WC-1527SCDM-217 User manual
-
Rev-A-Shelf 5LB-1550SSBL-118 Operating instructions
-
Rev-A-Shelf 5743-10-CR-1 Operating instructions
-
Rev-A-Shelf 4WCTM-24DM2-162 Operating instructions
-
-
-
-
-
-