FUVISION -Solar-1080SWF is an advanced security camera with a range of features to keep your home or business safe. With its 1080p resolution, you'll be able to see crystal-clear footage of anyone who comes near your property. The camera also has a wide-angle lens, so you can cover a large area with just one device.
One of the best things about the FUVISION -Solar-1080SWF is its long battery life. Thanks to its built-in solar panel, the camera can stay powered for up to 8-12 months on a single charge. This means you won't have to worry about changing batteries or running out of power.
FUVISION -Solar-1080SWF is an advanced security camera with a range of features to keep your home or business safe. With its 1080p resolution, you'll be able to see crystal-clear footage of anyone who comes near your property. The camera also has a wide-angle lens, so you can cover a large area with just one device.
One of the best things about the FUVISION -Solar-1080SWF is its long battery life. Thanks to its built-in solar panel, the camera can stay powered for up to 8-12 months on a single charge. This means you won't have to worry about changing batteries or running out of power.
Solar Powered Security Camera
ModelA9
Email:[email protected]
Facebook:https://www.facebook.com/FUVISIONCam
1. A9 solar camera can only be set up with 2.4g Wi-Fi network. (It's
ok to use Cell phone 4G data to live viewing it after the camera
was set up with 2.4g Wi-Fi network firstly.)
2. When the battery runs out, the camera can only turn on
automatically after the camera is charged more than 4 hours.
3. You may possibly need a Wi-Fi extender if your Wi-Fi signal is
weak around the yard where you want to install it.
4. At least 1-3 hours direct sunlight to the camera every day is
needed, the more sunshine the better to avoid manually charge
it frequently. (North side of the house is not a recommended
installation place)
5. Please format the micro SD card to FAT32 format and install the
card when camera powered off.(Micro SD card is not included
in the package)
6. Please charge your A9 camera before you set it up, it
usually takes up to 10-12 hours to fully charge it.Do not use any
power adaptor exceed 5V/2A,or it may damage the camera.
(There's no indicator to show charging status from the camera)
7. Make sure the distance between your phone,router and the
camera is no more than 1.5 feet when you're ready to pair the
camera. Ensure that the Wi-fi signal strength on your phone is
good.
8. The PIR range is 16 feet around,the recommend camera install
height is 8 feet around.To avoid too much false alarms, we
suggest you do not install the camera with nearby bushes,shrubs,
grasses and tree leaves coming into the PIR range.
9. To ensure an accurate motion detection function,it is suggested
to adjust the camera angle physically to focus the motion area
within the PIR suggested 16ft range.
10. If you install the camera on stucco,brick or concrete surface,
please mark 4 holes matching the bracket and then use a drill
driver to drill into the wall and insert the expansion screws to
hold the camera tightly
Warm tips before you go:
Product Diagram
Bracket
Solar Panel
MIC
PIR
Light Sensor
Status Light
LED
Lens
TF
DC/5V
RST
APP/WIFI
Charging cable to connect
external solar panel
TF
DC/5V
APP/WIFI
RST
Charging
lnsert SD card
Please charge the camera about 10-12 hours by plugging it
into a power source using the provided USB cable. After
connecting the camera with App, the App will indicate the
battery status.
Please format the SD card to FAT32 format (Application to
Windows system ONLY), then install the micro-SD card when
the camera is off. The camera only supports class 10 SD cards
with at least an 8GB capacity and a maximum capacity of 64GB
(There's no indicator to show charging status
from the camera)
SD Card
TF
DC/5V
APP/WIFI
RST
TF DC/5V
APP/WIFI RST
TF
DC/5V
APP/WIFI
RST
Solar Powered Security Camera
ModelA9
Package Includes
4 x Expansion Screws
1 x USB Cable
1 x User Manual
1 x Bracket
Camera
1 x Allen key 1 x Allen key
Make sure the distance between your phone,router and
the camera is no more than 1.5 feet when you're ready to
pair the camera.Ensure that the Wi-fi signal strength on
your phone is good.
1.Download the App
(works only with iOS & Android devices)
2.Turn on the camera
Please locate the“ Ubell” in your Google Play store,and
download the Ubell App from google play or apple store.
Press the RST button to turn on the camera, after 3
seconds, LED flashes blue. Then you will hear the following
voice “The camera is now ready to begin pairing”.
How to turn off the camera?
Press and hold on the RST button for 15 seconds, after
you hear music, LED will goes off, which means the camera
has been turned off.
Flash es b lu e
TF
DC/5V
APP/WIFI
RST
Please connect your phone to the 2.4Ghz wifi firstly
before you pair the camera, make sure your router
password in mind before you start the pairing process.
1) Click "Add a device" and then choose "Setup device",
click "Yes", when you hear the following voice “ The
camera is now ready to begin pairing”.
2) Input the CORRECT WiFi password of your router,
if you input a wrong password you will not be able to
connect it successfully. Click the eye icon to double
confirm the password you entered correct
3.Pairing the camera with the App
Click the icon to double
confirm the password you
entered is correct
Your own wifi name
3) Enter into the “search device” page, make sure to turn up
you phone’s volume to the Maximum, you will hear the
following voice: “Pairing Information Received”.
4) You have connected the device to the App successfully.
Now you can setup a password to log in, which could
protect your privacy. The camera password should be
more than 8 characters in length including numbers
and letters.
What should you do if you can not add the
camera to the APP successfully?
1. Reboot your router to make sure the WiFi
network smooth.
2. Reset the camera using the pin included.
3. Turn up your phone’s volume to the Maximum.
4. Re-do the In-App setup as per user manual
page 5 to 7.
5. Please confirm again your WiFi password correct.
6. Please make sure your router setting is DHCP
enabled, otherwise your router will not send out
WiFi signal for any wireless device for pairing up.
Please choose " Non chinese
mainland users” or you will
not get proper notifications
5) Congratulations! Now you can live view the camera on
your phone anytime and anywhere.
If you're unable to pair the camera,
Please check below suggestions:
How to reset camera:
1.Please reset the camera (using the pin to reset the camera)
to default after you fully charged the camera.
2.Please turn up your phone volume to the maximum,since
the camera pair through sound wave.
3.Please put the camera,phone as near as to your router
(within 1.5 feet) to get a strong wifi signal strength.
4.Please click on the eye icon when you input your router wifi
password to make sure your wifi password CORRECT.
5.Please make sure your router setting is DHCP enabled,
otherwise your router will not send out WiFi signal for any
wireless device for pairing up.
Press and hold on the reset button for 7 seconds to reset the
device. Don’t release the button until you hear the voice"Di",
then you will hear "system reset".
TF
DC/5V
APP/WIFI
RST
4.How to Share Your Camera And
Password with More Users
After you finish the connection with the App, click and
choose “Share QR code” .
Other users need to download the App first, and then scan
the below QR code.
Note:
1.Your camera password can be seen by the invited users,but they can
not modify it.
2.The invited users can change all the camera settings,so the camera
will work as per the last change made on the settings among all users.
3.If your camera does not work as you set before,please check
the settings from the invited users’ device.
Share QR code
Silence: You could choose to mute all incoming
notification or call in, all motion triggered videos will
be saved properly to cloud storage or Micro sd card.
Notification:
Camera will receive notification and
banner.
Call in:
Camera will receive call in sound and banners
the same time with a “ Dingdong” sound.
You can play back all cloud videos here. Cloud video
length is 8 seconds defaulted and 20 free video clips
per day. The oldest footages will be overwritten by the
newest one day by day.
Push Mode
Cloud storage
1
2
3
Check Calendar for video history
Download video to your phone
Delete all Cloud videos
Delete current video
Please find the orange color for the video event and use
two fingers to zoom out the timeline and then put the line
to the head of the orange color and wait for the playback
Micro sd card Video playback
Zoom out to playback
Check your camera signal strength
Recommended height to install the camera
If your camera get numerous motion alerts unexpected
1) Please adjust your camera installation angle a bit down to focus the
motion area.
2) Please change your PIR sensitivity to Low to reduce the PIR
sensitivity.
3) Do not install the camera with nearby bushes,shrubs,
grasses and tree leaves coming into the PIR range.
1
Camera
Check in App
WiFi extender
Router
If not satisfied with video smoothness,
and signal strength in App is not strong,
we would suggest adding wifi extender
between the Router and the camera.
2
We suggest installing the camera about 8ft. You
may adjust the camera angle physically according
to the live view in your mobile. to focus your
motion area to get the more accurate motion
triggered events.
Adjust the bracket on the wall and then mark 4
holes for mounting. Fix the bracket to the wall by
expansion screws.
3
How to take apart the bracket?
4
1 2
3
4
1 x Allen key
How to fix the solar panel ?
The solar panel can be adjusted in 0-90 degree
angle.Use the Alley Key to fix the panel.
5
Image Quality Resolution
Lens angle
Video format
Frames per
second
SD card
support
Output
Intput
WiFi
Battery capacity
Standby time
Power
consumption
Temperature
Humidity
20%~85%
(Non-condensing)
-20~+60(-4 F-140 F)
6W(run)/
0.003W (standby)
Max 8-12 months
10000mAh
Built-in speaker
Built-in microphone
2.4GHz
15fps
8GB-Max 64GB
H.264
FOV 160°
1080P
Lens
Specifications
Video
Specifications
Audio
Communications
Battery
Applicable
Environment
System
Suppport
PIR
Night Vision
Working time for
fully charged
Waterproof
Turn on the camera
PIR was triggered
Camera working
Standby mode
Connect network successfully
Android 2.3 above/ iOS 7.0 above
PIR angle FOV 120°
PIR range
Range
Continuously daytime
recording time
Continuously night vision
recording time
IP grade
LED flashes red once and goes
off and LED flashes blue
LED stays blue
LED stays blue
LED goes off
LED flashes red once and goes
off and LED stays blue
16ft
Up to 32ft
Max 36 hours
Max 14 hours
IP66
LED Status
Important:
Please keep the Cloud Storage turned on to
ensure the camera's time kept synchronized
with your phone's time.
1.click ,you could live viewing videos.
Wifi signal strength
Tips: Please make sure your camera
has a full bar of wifi strength to
ensure a smooth live view speed.
(A wifi extender is recommended
to install beside the camera if needed)
Battery charging sign
When camera exposed to sunlight,the battery will
keep charging in green.
During night or fully charged,the battery will
stay white.
Tips : If your battery sign will not show correct
status as above,please remove the solar panel
and then re install it to the camera body.Or
contact FUVISION support team for a replacement
at [email protected] All friendly customer
service staffs are ready to assist you.
Click here to chose the resolution to HD (1080P)
OR SD(720P)
Number of users
Tips: If you have invited a second users to visit
your camera.Please pay attention to below
points:
1.Your camera password can be seen by the
invited users,but it can not be modified.
2.The invited users can change all the camera
settings,so the camera will work as per the
last change made on the settings among all
users.
3.If your camera does not work as you set
before,please check the settings from the
invited users' device.
Low power indicator,please recharge the camera
manually using the provided USB cable
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
FUVISION -Solar-1080SWF is an advanced security camera with a range of features to keep your home or business safe. With its 1080p resolution, you'll be able to see crystal-clear footage of anyone who comes near your property. The camera also has a wide-angle lens, so you can cover a large area with just one device.
One of the best things about the FUVISION -Solar-1080SWF is its long battery life. Thanks to its built-in solar panel, the camera can stay powered for up to 8-12 months on a single charge. This means you won't have to worry about changing batteries or running out of power.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
XPARKIN B0BRJBVW24 Operating instructions
-
Ankway Solar Energy Alert PTZ Camera User manual
-
Emerson ER108003 Owner's manual
-
LITOM LTCD011AB User guide
-
Morris MHR-20044S User manual
-
NightWatcher NW765 User manual
-
OzSpy MDC-KP09 User manual
-
Philips VTR8060/93 User manual
-
VIONMIO L28 Low Power Consumption Mini Wi-Fi Camera User manual
-
centechia CT101 User manual
