Align-Pilates Wall Unit & Barre Bar Installation guide

Brand: Align-Pilates

Model: Wall Unit & Barre Bar

Type: Installation guide

Wall Unit & Barre Bar Installation Instructions

Contents

BAG 1:

4 X Double ended Dog Clips

4 x Karabiners

8 x Black Bolt Cover Inserts

4 x Sprung Locator Bolts

2 x Screw In Knobs

4 x Black Gaskets

1 x Wrench

1 x 5.5mm Allen Key

BAG 2:

4 x 30mm Black Hex-Head Bolts

8 x M8 Nylock Nuts

8 x Washers

BOX:

1 x PAIR Barre Bar Carriage Holders

1 x PAIR Spring Carriage Holders

1 x Top Maple Frame (Has Align Pilates LOGO front centre)

1 x Bottom Maple Frame

2 x Chrome Uprights

4 x Springs (2 long purple and 2 x short yellow)

1 x Barre Bar

1 x Trapeze bar

1 x Pair of Handles

1 x Pair of Foot straps

2 x Metal wall mounting plates

Installation Guide

Align-Pilates recommend using a suitably qualified Tradesman to install this product. Such a Tradesman can

assess the suitability/strength of the wall to accept the unit and can select the appropriate wall fixing to

attach the unit securely to the wall. Align-Pilates does not supply wall fixings with this product as these are

dependent on the type of wall which the unit is being attached to.

Note before Installing: The Bottom Maple Frame bar & bracket are usually installed on the floor, however

where the floor is uneven the Barre bar frame can be installed off the floor. In these cases, please keep in

mind the Barre bar in its lowest position will be 12.5cms higher than the mounting position. Similarly if

there is a skirting board present you can either a) Install the unit above the skirting board b) Remove the

section of skirting board c) Make a timber spacer to place behind the top wall mounting plate, to be of

equal thickness to the skirting board.

1) Lay out the chrome uprights and the top and bottom Maple

Frames on the floor as in fig 1. The maple bar with the

Align-Pilates logo plate is the top and the eyelets should face

down toward the bottom maple bar.

2) The inside of each chrome uprights has only 4 holes.

Slide on one of the spring carriage holders and

then the Barre bar carriage holder followed by the

Gasket, black face first, onto the Chrome uprights from the

bottom as shown in fig 2.

3) Using the Allen key, loosely attach the bottom maple

frame using the 30mm Black Hex headed bolt to each of

the chrome uprights. At this point double check the chrome

uprights have 10 holes facing outward and that the

carriage holders are on correctly.

4) At the top of each chrome upright, slide a Black gasket, Black side face first onto upright.

5) Using the 2 remaining Black Hex headed bolts tighten the top Maple Bracket fully and then tighten

the bottom Maple Bracket fully also.

6) Take the frame to the wall and using a SPIRIT LEVEL, ensure the top of the frame is horizontal. Mark

this position and then set aside frame.

7) Remove the metal mounting plates from the Top Maple frame. Now affix this metal bracket using

strong fixings suitable for the your wall type (seek advice from a qualified Tradesman).

8) Insert frame over top metal mounting plate and slide into position. Check Horizontal again using a

SPIRIT LEVEL and mark lower wall attachment. Again affix as above.

9) Both wall mounting plates should now be correctly attached to the wall and in position to receive

the Maple frame. slide the frame over the protruding bolts. Add washer to bolt and gradually

tighten each of the 8 nuts until the Barre Bar frame is securely attached to the wall.

10) Insert the black plastic blanking plates that cover the bolt holes.

11) Remove the white self adhesive backing of each gasket and stick in situ to the maple frame.

12) Screw in the black Sprung Locator Bolts into the Spring and Barre Bar carriages.

13) Slide Barre bar through the metal rings on each side and attach into place using the twist knobs.

14) Clip double ended dog clips to each end of the purple springs. Clip a karabiner to each end of the

short yellow springs. Clip a handle or foot strap to each of the purple springs and then attach the

top end to the spring carriage. Clip the yellow spring karabiners to the left and right metal loops in

the top of the Barre frame and the bottom karabiners to the trapeze bar.

FIG 1

FIG 2

Align-Pilates Wall Unit & Barre Bar Installation guide

Brand: Align-Pilates

Model: Wall Unit & Barre Bar

Type: Installation guide

Download PDF

report

Align-Pilates Wall Unit & Barre Bar Installation guide

Align-Pilates Wall Unit & Barre Bar Installation guide

Related papers

Other documents