UBI EasyCoder 101 Startup Manual

Brand: UBI

Model: EasyCoder 101

Type: Startup Manual

This manual is also suitable for

UBI EasyCoder 101

The UBI EasyCoder 101 is a versatile and powerful label printer that offers a wide range of features and capabilities to meet your labeling needs. With its compact size and easy-to-use interface, the EasyCoder 101 is perfect for a variety of applications, from small businesses to large corporations.

Some of the key features of the UBI EasyCoder 101 include:

High-resolution printing: The EasyCoder 101 can print labels with a resolution of up to 300 dpi, ensuring that your labels are clear and easy to read.
Fast printing speed: The EasyCoder 101 can print labels at speeds of up to 4 inches per second, making it ideal for high-volume printing applications.

UBI EasyCoder 101

Some of the key features of the UBI EasyCoder 101 include:

High-resolution printing: The EasyCoder 101 can print labels with a resolution of up to 300 dpi, ensuring that your labels are clear and easy to read.
Fast printing speed: The EasyCoder 101 can print labels at speeds of up to 4 inches per second, making it ideal for high-volume printing applications.

UBI Shell 4.0 Standard – Startup Manual

CONTENTS

Introduction Contents .................................................................................. 1

Copyrights and Trade Marks ................................................... 2

Startup Files ............................................................................ 3

Using the Print Key and Headlift Handle ................................. 4

Using UBI Shell Starting Up with UBI Shell ...................................................... 5

Options in UBI Shell................................................................ 6

Overview ................................................................................ 9

Setup Mode Step-by-Step Instructions....................................................... 10

Setup Overview..................................................................... 14

Terminal Setup Starting Terminal Setup ......................................................... 15

Solving Communication Problems ........................................ 15

Using Terminal Setup ............................................................ 16

Selecting an Application........................................................ 17

Changing the Setup ............................................................... 18

Exiting Terminal Setup .......................................................... 19

Setup Parameters................................................................... 20

Line Analyzer Description............................................................................ 21

UBI Shell 4.0 Standard

Startup Manual

Edition 2, June 1995

Art. No. 1-960372-01

UBI Shell 4.0 Standard – Startup Manual

Information in this manual is subject to change without prior notice and does not represent a commitment

on the part of UBI Printer AB.

EasyCoder and LabelShop are trademarks of United Barcode Industries (UBI).

Apple and Macintosh are registered trademarks of Apple Computer Inc.

Centronics is a registered trademark of Centronics Data Computer Corp.

Windows is a trademark of Microsoft Corporation.

UBI Shell 4.0 Standard – Startup Manual

UBI Shell is a so called startup program (also called “autoexec-

file”), i.e. a program that automatically starts running when the

printer is turned on. UBI Shell helps the operator to choose between

a number of standard or custom-made application programs and to

start certain useful facilities, as listed below.

Application Programs

• UBI LabelShop (WYSIWYG label design program)

• UBI Windows Driver (for printing from Windows programs)

• UBI Macintosh Driver (for printing from Macintosh programs)

• UBI Fingerprint (for writing your own programs)

• UBI Direct Protocol (easy-to-use slave protocol)

• Line Analyzer (prints all characters received by printer)

• Other application programs in the printer's memory

Other Facilities

• Terminal Setup (remote setup and UBI Shell control)

• Setup Mode (manual setup w. limited options)

• Print Setup (printing setup on label)

• Testfeed (formfeed + auto-adjust of the LSS)

• Test Label (printing of test labels)

• Ser-Com Reset (resetting communication to default )

• Clear RAM Memory (erasing the printer's RAM memory)

• Reboot (restarting the printer)

There can be one startup file stored in each of the following parts of

the printer's memory: RAM, ROM, and memory cards. If there are

startup files stored in more than one place, they will be used with the

following priority:

1. Dos-formatted memory cards (SRAM).

2. Printer's RAM memory.

3. Non DOS-formatted memory cards (SRAM or OTPROM).

4. Printer's ROM memory, e.g. the configuration EPROM's.

This implies that if you e.g. have UBI Shell stored in the printer's

configuration EPROM's and insert a memory card with another

startup file before you turn on the printer, the startup file of the

memory card will be used.

INTRODUCTION

Startup Files

EPROM = Erasable Programmable

Read-Only Memory

OTPROM = One-Time

Programmable Read-

Only Memory

RAM = Random Access Memory

ROM = Read-Only Memory

SRAM = Static Random Access

Memory

UBI Shell 4.0 Standard – Startup Manual

Load

DOWN

PULL/TIREZ

UBI

EasyCoder 101

Power

Ready

Error

Using the Print Key and

Headlift Handle

INTRODUCTION, cont'd.

In EasyCoder printers without keyboard, the Print key has been

given dual functions in UBI Shell by combining it with the printhead

lift handle. This is used for navigating between the menus in UBI

Shell and for selecting various options.

EasyCoder 401 and EasyCoder 501

EasyCoder 201 II

EasyCoder 101

Headlift Handle

Print Key

Power

Ready

Error

Headlift Handle

UBI Shell 4.0 Standard – Startup Manual

USING UBI SHELL

Starting Up with UBI Shell

A few seconds after you have turned on the power to the printer, the

countdown menu of the UBI Shell program will be displayed:

PRINT=UBI SHELL

5 sec. v.4.0

Now you have 5 seconds to enter UBI Shell by pressing the

< Print > key with the printhead lowered (the printhead should

always be lowered at startup).

Provided you have a working two-way communication with a

terminal program in a host computer, you may – as an alternative –

enter the Terminal Setup by transmitting “TTT” or “ttt” to the

printer. The Terminal Setup is described in a separate chapter later

on.

The lower line keeps you informed how much time you have left.

Should the time run out before you have taken any action to enter

UBI Shell or the Terminal Setup, the last selected application in UBI

Shell will be opened. This implies that if you use the same

application all the time, you will only need to turn on the power,

once the application has been selected.

If no other application has been selected yet, the default choice will

be displayed when the countdown is completed, e.g.:

UBI FINGERPRINT

6.0

This message means that you have entered the immediate mode of

UBI Fingerprint with "uart1:" selected as std I/O channel (see UBI

Fingerprint manuals).

If you want to enter another application, just turn off and on the

power and enter UBI Shell before the countdown is completed.

If you enter the UBI Shell from the countdown menus (Head Down/

Press Print), the Select Application menu will be displayed:

UBI SHELL

SEL. APPLICATION

In this menu, you can choose between three options:

• Go to a stack of menus, where you can select an application

program, by pressing < Print > without lifting the printhead.

• Go to the Facilities part of UBI Shell by lifting the printhead and

pressing < Print >.

• Start the Terminal Setup program by transmitting “TTT” or “ttt”

from the host.

Continued!

UBI Shell 4.0 Standard – Startup Manual

Options in UBI Shell

Continued!

USING UBI SHELL, cont'd.

/. A prerequisite is that the program is

provided with the extension “.PRG”.

However, some original UBI utility

programs are excluded from the list:

ERRHAND.PRG

ERRH910.PRG

FILELIST.PRG

MKAUTO.PRG

TEST910.PRG

In UBI Shell, the options are presented in stacks of menus, organ-

ized as infinite loops, where you can move around and select the

desired option, as illustrated by the diagram at the end of this

chapter.

Select Application

The Select application option allows you to enter a stack of menus

showing the different application programs in the printer's memory

Note that after having selected an application, you must wait for

the printer to restart and perform the 5 seconds countdown before

the selected application is opened.

As standard, EasyCoder printers fitted with UBI Shell will contain

the following application programs:

❑ UBI LabelShop selects the standard serial interface "uart1:" as

standard

IN/OUT channel and sets up the printer for the UBI

LabelShop label design program, which you can run on a

personal computer with Microsoft Windows 3.1.

Refer to the UBI LabelShop User's Manual.

❑ UBI Windows Driver selects the optional parallel interface

"centronics:" as standard IN/OUT channel and sets up the printer

for the UBI Windows Driver, which you can use on a personal

computer to produce printouts from almost any standard pro-

gram run under Microsoft Windows 3.1, e.g. word processors,

spreadsheet programs, drawing programs etc.

Refer to the UBI Windows Driver Installation Instructions.

❑ UBI Macintosh Driver makes it possible to connect an Apple

Macintosh computer to any RS 232C communication port on

the printer. The program automatically detects which port is

used and resets its communication parameters. In case of

"uart1:", the baudrate is set to 19,200 and in case of "uart2:" or

"uart3:" to 38,400. The UBI Macintosh Driver is installed in the

System folder of the Macintosh computer and can be selected by

means of the Chooser. Then you can print from almost any

standard program, e.g. word processors, spreadsheets, drawing

programs, etc.

Refer to the UBI Macintosh Driver Installation Instructions.

UBI Shell 4.0 Standard – Startup Manual

Continued!

USING UBI SHELL, cont'd.

Options in UBI Shell, cont'd.

❑ UBI Fingerprint is used to create or modify programs written

in the UBI Fingerprint programming language. This option

requires that you also select a standard

IN/OUT channel, i.e. the

channel you want to use for communication between the printer

and the computer or terminal on which you will write your

program. Normally, select "uart1:" (default). For programming,

do not use the parallel "centronics:" channel (one-way commu-

nication only).

Refer to the UBI Fingerprint Reference Manual and the UBI

Fingerprint Programmer's Guide.

❑ UBI Direct Protocol is an easy-to-use printer protocol for

downloading label layouts and variable input data to a printer

from a host computer. This option requires that you also select

a standard

IN/OUT channel, i.e. the channel you want to use for

communication between the printer and the computer or termi-

nal. Normally, select "uart1:" (default).

Refer to the UBI Direct Protocol Programmer's Guide.

❑ Line Analyzer is a UBI Fingerprint programs that captures all

characters received by the printer on a specified communication

channel and prints them on labels.

Refer to the chapter “Line Analyzer” later in this manual.

❑ Other Application Programs

If the printer contains any other application programs – standard

or custom-made – these will presented as additional options.

When you have selected an application, the printer beeps and the

error lamps comes on. Then the display goes blank as the printer is

restarted. After a short moment, the printer starts up and the UBI

Shell countdown menus are shown again. You can either enter UBI

Shell or ignore the countdown menus and just wait 5 seconds for the

selected application to be started.

As long as you do not select another application in UBI Shell, the

same application will be automatically selected at each power-up,

unless you enter UBI Shell in the countdown menus.

UBI Shell 4.0 Standard – Startup Manual

USING UBI SHELL, cont'd.

Default Communication Setup :

Baudrate: 9600

Parity: none

Char. length: 7 bits

Stopbits: 2

Flow control: XON/XOFF to/from host

New line: CR/LF

As an alternative to selecting an application, you can step through

a number of useful facilities:

Setup Mode

The Setup Mode allows you to adjust the Label Stop Sensor (LSS)

and to read the printer's present setup in its display window. In

EasyCoder 101, you can also set up the printhead resistance,

whereas all other models have automatic resistance detection. For

information on the various setup parameters, please refer to the

Technical Manual for the printer model in question. The Setup

Mode is further described in a separate chapter later on.

Print Setup

The Print Setup option allows you to produce a printout of the

printer's current setup values.

Testfeed

The Testfeed option allows you to feed out one label, ticket, tag or

piece of strip while the printer auto-adjusts its paper feed and label

stop sensor or black mark sensor. It is recommended to perform at

least two Testfeed operations.

Test Label

The Test Label option allows you to print a series of four test labels

in order to test the printout quality and printhead alignment. The

labels are presented in an infinite loop, so you can print the series

over and over again.

Ser-Com Reset

The Ser-Com Reset option allows you to reset the serial communi-

cation setup parameters for all serial communication channels to

their respective default values.

Clear RAM Memory

The UBI Windows Driver and the UBI Macintosh Driver require a

certain amount of free memory space in the printer, depending on

the size of the print image. The Clear RAM Memory option is used

to erase most of the printer's RAM memory in order to provide such

memory space, if necessary. Only use the Clear Memory option

when you experience problems with printing via any of the drivers

and when you are sure that you do not have any irreplaceable files

in the RAM memory!

Reboot

The Reboot option has the same effect as turning off and on the

power to the printer. To exit UBI Shell without having selected any

application program, use Reboot or restart the printer. Then wait for

the 5 seconds countdown without taking any action, and the last

selected application will be opened.

Options in UBI Shell, cont'd.

Continued!

UBI Shell 4.0 Standard – Startup Manual

USING UBI SHELL, cont'd.



ARE YOU SURE ?

Y=H DOWN/ N=H UP



RAM MEMORY

CLEARED

HD/PP HD/PP HD/PP

HU/PP



ARE YOU SURE ?

Y=H DOWN/ N=H UP



SER-COM RESET

PERFORMED

Enter



UBI SHELL

SER-COM RESET



UBI SHELL

CLEAR RAM MEMORY



UBI SHELL

REBOOT

Exit UBI Shell and enter last selected application!

 



STD I/O CHANNEL

UART1

STD I/O CHANNEL

UART2

STD I/O CHANNEL

UART3

STD I/O CHANNEL

CENTRONICS



LSS ADJUST



CONTRAST



SEL. APPLICATION

optional applic.



SEL. APPLICATION

Fingerprint 6.0



UBI SHELL

SETUP



See Technical 

Manual



SEL. APPLICATION

WINDOWS DRIVER

SEL. APPLICATION

MACINTOSH DRIVER



PRINT=UBI SHELL

5 sec. v.4.0

PRINT=UBI SHELL

4 sec. v.4.0

PRINT=UBI SHELL

3 sec. v.4.0

PRINT=UBI SHELL

2 sec. v.4.0

PRINT=UBI SHELL

1 sec. v.4.0

Last selected

application is started

Default: 

UBI Fingerprint

w. std I/O= "uart1:"

No action taken

POWER ON

Printhead Up/

Press Print key:

Proceed to next menu

Legend:



UBI SHELL

SEL. APPLICATION



SEL. APPLICATION

Direct Protocol



SEL. APPLICATION

optional applic.



SEL.APPL rom:

LINE_ALY.PRG

HU/PP: SET

HD/PP: VIEW

UBI Shell for EasyCoder Printers w/o Keyboard



SEL. APPLICATION

LABELSHOP

Enter Terminal Setup 

by transmitting T T T 

to printer, when menus 

marked with grey 

are displayed!

HU/PP

Printhead Down/

Press Print key:

Accept displayed

option and proceed

HD/PP



UBI SHELL

TEST LABEL



UBI SHELL

TESTFEED

Perform a Testfeed, i.e. feed out a blank copy and

autoadjust the label stop sensor.

Print a series of test labels in a loop. 

Press Print for each new label.

Print a list of current setup values.

Resets comm. setup

to default values on

all serial channels.

Clears printer's

RAM memory.



UBI SHELL

PRINT SETUP

HD/PP

HU/PP

HD/PP

HD/PP HD/PP HD/PP

HD/PP

HD/PP HD/PP

HD/PP

HU/PP

HD/PP

HU/PP

UBI Shell 4.0 Standard – Startup Manual

Continued!

The Setup Mode can only be used to manually change the adjust-

ment of the label stop sensor/black mark sensor, to read the present

setup values and – in case of EasyCoder 101 – to change the

printhead resistance setup. To change any other setup parameters,

use the Terminal Setup in UBI Shell or a setup file (see

SETUP

statement in the UBI Fingerprint manual).

❑ Turn on the power. After a few seconds, the display shows:

PRINT=UBI SHELL

X sec. v.4.0

❑ Press < Print > with the printhead down. The display shows:

UBI SHELL

SEL. APPLICATION

❑ Lift the printhead and press < Print >. The display shows:

UBI SHELL

SETUP

❑ With the printhead down, press < Print >:

HU/PP: SET

HD/PP: VIEW

There are two alternative ways to go on:

1. Pressing < Print > with the printhead lifted allows you to

change the printhead resistance (EasyCoder 101 only) and

the LSS setup.

2. Pressing < Print > with the printhead lowered lets you

view the current values of all setup parameters.

EasyCoder 101 only:

❑ Assuming you have pressed < Print > with the printhead

lifted, the display will show:

HEAD RESISTANCE

680

The printhead resistance controls the amount of energy trans-

mitted to the printhead resistors (“dots”) and must be adjusted

according to the marking on the printhead, whenever a print-

head is replaced. An incorrect resistance value may rapidly

damage the printhead beyond repair.

SETUP MODE

Step-by-Step Instructions

UBI Shell 4.0 Standard – Startup Manual

Continued!

EasyCoder 101 only, cont'd.:

❑ To change the resistance, proceed as follows:

• With the printhead lifted, press < Print >. The value on the

lower line will change to 552.

• Press < Print > once and the value will change to 560.

• Press < Print > again and the value will be increased by 10, i.e.

to 570.

• Each time you press < Print >, the value will be increased by

10 until the highest possible value (748) is obtained. Then the

loop will start all over again at 552.

• Press < Print > repeatedly until the displayed value comes as

close as possible to the value written or labelled on the

printhead.

• Finally lower the printhead and press < Print > to set up the

printer according to the displayed resistance value.

All Printers:

❑ The display shows:

LSS ADJUST

❑ Lift the printhead and press < Print >, and the display changes

to show the LSS indicator menu, e.g.:

LABEL <103> GAP

■

❑ Often it will suffice just to perform a couple of TESTFEED

operations, which allows the printer to auto-adjust itself. With-

out pressing < Print >, lower and lift the printhead. A blank

label (or the equivalent) will be fed out. When the paper feed

operates as expected, you can exit the LSS adjustment by

lowering the printhead and pressing < Print >, which will take

you to the part of the program where you can check all setup

parameters.

❑ If you cannot make the paper feed operate properly by means of

TESTFEEDs, you will have to adjust the LSS as described below.

❑ Before the LSS is adjusted, the printer must be set up for the type

of paper web you intend to use, i.e. “Label (w gaps)”, “Ticket (w

mark)”, “Ticket (w gaps)”, “Fix length strip”, or “Var. length

strip”. “Tickets (w mark)” is not available in all models.

Step-by-Step Instructions,

cont'd.

SETUP MODE, cont'd.

UBI Shell 4.0 Standard – Startup Manual

Continued!

❑ Label (w gaps):

Put a piece of paper with backing paper into the sensor. The

cursor should appear at the left side of the menu:

LABEL <103> GAP

■

Put a piece of backing paper without any label into the sensor.

The cursor should move to the centre of the menu:

LABEL <103> GAP

■

Finally remove all paper web from the sensor. The cursor should

move to the right side of the menu:

LABEL <103> GAP

■

❑ Ticket (w mark), certain models only:

Put the paper into the sensor so there is no black mark close to

the LSS. The cursor should appear at the right side of the menu:

MARK <103>TICKET

■

Move the paper so the black mark becomes situated between the

two parts of the sensor. The cursor should move to the left side

of the menu (the same applies when no paper is fitted):

MARK <103>TICKET

■

❑ Ticket (w gaps), Fix Length Strip and Var. Length Strip:

Put the paper into the sensor, making sure there is no gap close

to the LSS. The cursor should appear at the left side of the menu:

LABEL <103> GAP

■

In case of tickets, move the paper so the gap becomes situated

above the sensor. In case of strip, remove the paper completely.

In both cases, the cursor should move to the left side of the menu:

LABEL <103> GAP

■

❑ If the cursor does not behave as described, the LSS must be

adjusted.

Step-by-Step Instructions,

cont'd.

SETUP MODE, cont'd.

UBI Shell 4.0 Standard – Startup Manual

Step-by-Step Instructions,

cont'd.

SETUP MODE, cont'd.

❑ The value in the centre of the upper line shows the level of the

LSS. Select another level by pressing < Print > with the print-

head lifted.

EasyCoder 101 and EasyCoder 201 II:

Each time you press < Print >, the level will increase one step

in a loop of four levels (000-001-002-003-000-001-002-003-

000....).

EasyCoder 401 and EasyCoder 501:

Each time you press < Print >, the level will increase 8 steps in

a loop between 0 and 127 (0-7-15-23-31-........-119-127-0–7....).

Keep trying until you find a level, that places the cursor as

described.

❑ When the adjustment looks right, lower and lift the printhead.

This will produce a

TESTFEED, i.e. it will allow the printer feed

out one label, ticket, tag or piece of strip in order to adjust itself

and to allow you to check that the paper feed works correctly. At

least two

TESTFEEDs should be produced before you go on.

❑ If you cannot make the LSS work correctly by following the

instructions above, you may – as a last resort – need to adjust the

potentiometer on the CPU board, see the Technical Manual of

the printer model in question.

❑ Try different combinations of potentiometer settings and LSS

levels until the cursor is positioned correctly.

❑ When you are satisfied that the LSS is set up correctly, lower the

printhead and press < Print >. That will set the LSS and take

you to the part of the Setup Mode, where you can view all setup

parameters, i.e. to the same part as if you had entered the Setup

Mode with the printhead lowered:

CONTRAST

❑ Now you can check all current setup values (except the LSS

adjustment and the printhead resistance), one after the other, by

pressing < Print > with the printhead lowered. The para-

meters are organized in a loop so you can step through them over

and over again (see the overview on next page).

If you want to change any of these setup parameters, you must

use a setup file (see

SETUP statement in the UBI Fingerprint

manual) or use the Terminal Setup in UBI Shell.

❑ To leave, lift the printhead and press < Print >. This will take

you back to the UBI Shell program.

UBI Shell 4.0 Standard – Startup Manual

SETUP MODE, cont'd.

HEAD RESISTANCE

748

UBI SHELL

SETUP

HU/PP: SET

HD/PP: VIEW

HEAD RESISTANCE

...

HEAD RESISTANCE

...

HEAD RESISTANCE

580

HEAD RESISTANCE

570

HEAD RESISTANCE

560

HEAD RESISTANCE

680

HEAD RESISTANCE

552

HU/PP

LSS ADJUST LABEL <103> GAP

■

HD/PP

HU/PP to scroll

TESTFEED

HD + HU

HD/PP

HU/PP to change level

(000-001-002-003-000-001-002-003-000 ...

0-7-15-23-31-39-47-55.....-119-127-0-7...)

UART1,BAUDRATE

9600

UART1,PARITY

NONE

UART1,CHAR-LEN

UART1,STOPBITS

UART1,RTS/CTS

DISABLE

UART1,ENQ/ACK

DISABLE

U1,XO,FROM HOST

ENABLE

U1,XO,TO HOST

ENABLE

CONTRAST

UART1,NEW LINE

CR/LF

XSTART

WIDTH

832

LENGTH

1200

MEDIA TYPE

LABEL (w GAPS)

PAPER TYPE

UBI HP 20

STOPADJ

START ADJ

REC BUF UART1

300

TRANS BUF UART1

300

PERFORMANCE

NORMAL

IMAGE BUFF SIZE

HD/PP

HD/PP HU/PP

➜

Menus in this example show default

setup for an EasyCoder 501 with an 8

dots/mm printhead.

Legend:

HU/PP= Press Print with Printhead Up

HD/PP = Press Print with Printhead Down

HD = Lower Printhead

HU = Lift Printhead

HU/PP

Setup Overview

HD/PP

➜

EasyCoder 101 only

All others

➜

HD/PP

UBI Shell 4.0 Standard – Startup Manual

TERMINAL SETUP

The Terminal Setup program in UBI Shell allows the operator to

control the whole UBI Shell program remotely from a host compu-

ter or terminal and also to read and change the printer's setup.

Obvious prerequisite are that there must be a working two-way

(serial) communication between printer and host, and that the host

runs a suitable communication program (e.g. MS Windows Termi-

nal) that can transmit and receive data in ASCII format, i.e.

printable characters.

You can enter Terminal Setup by transmitting three uppercase or

lowercase T characters (TTT or ttt) while the printer either shows

the UBI Shell countdown menus or the Select Application menu.

If this does not work, the communication protocols of the printer

and the host probably do not match, or there is some other

communication error, e.g. a defect communication cable, wrong

port selected on the host, or cable connected to some other port than

"uart1:" on the printer

You can check the printer's communication setup by entering UBI

Shell and go to the “Facilities” part. There, you will find a number

of options that allow you to read or change the communication setup

of the printer:

• Setup

This option allows you to read the communication setup.

• Print Setup

Here you can print the current setup on one or more labels.

• Ser-Com Reset

This option allows you to reset the communication parameters for

all serial communication channels on the printer to default values.

After having read the present communication setup for "uart1:" on

the printer, change the communication setup of the host according

to the printer's setup.

If this for some reason is impossible, reset the printer's serial

communication setup to default by means of the “Ser-Com Reset”

option, then change the setup of the host accordingly.

Once printer and host has been set up with the same communication

parameters, go to the “Select Application” menu and use the triple

T (TTT) to start Terminal Setup. There you can change the printer's

setup to the desired protocol. Turn off the printer, change the setup

of the host to the desired protocol, and start up the printer again.

Now the communication should work.

/. By default, "uart1:" is standard IN/OUT

channel and should be used for communi-

cation between printer and host, e.g. for

running Terminal Setup or for program-

ming. However, other ports could be

appointed standard IN and/or OUT chan-

nel by means of the UBI Fingerprint state-

ment SETSTDIO. Refer to the UBI Finger-

print manuals for further information.

Starting Terminal Setup

Solving Communication

Problems

UBI Shell 4.0 Standard – Startup Manual

TERMINAL SETUP, cont'd.

Using Terminal Setup

The Terminal Setup program is self-instructing by means of prompts.

You can move around in UBI Shell in the same manner as when you

control UBI Shell manually by means of the printer's display,

< Print > key and Headlift.

The Setup part of Terminal Setup follows the same structure as

setup files, see later in this chapter. Comprehensive explanations of

the various setup parameters can be found in the Technical Manual

for the printer model in question.

When you transmit the triple T (TTT) to the printer, the following

message will appear on printer's display:

SETUP FROM

TERMINAL

On the screen of the host, another message will appear:

-----------------------------------------------

Welcome to UBI SHELL v.4.0 in terminal mode

-----------------------------------------------

Answer Y <CR> for Yes, <CR> for No.

----------------

UBI SHELL

SEL. APPLICATION

----------------

(Y / N):

From here on, you can move around in UBI Shell according to the

diagram in the chapter “Using UBI Shell” by answering Y (=Yes)

or N (=No) to the prompts that successively appear on the screen.

Note that the program also accepts the corresponding lowercase

characters, e.g. y and n.

UBI Shell 4.0 Standard – Startup Manual

TERMINAL SETUP, cont'd.

This example shows how you for example can select the UBI

Fingerprint application:

----------------

UBI SHELL

SEL. APPLICATION

----------------

(Y / N):Y

----------------

SEL. APPLICATION

LABELSHOP

----------------

(Y / N):N

----------------

SEL. APPLICATION

WINDOWS DRIVER

----------------

(Y / N):N

----------------

SEL. APPLICATION

MACINTOSH DRIVER

----------------

(Y / N):N

----------------

SEL. APPLICATION

UBI Fingerprint 6.0

----------------

(Y / N):Y

----------------

STD I/O CHANNEL

UART1

----------------

(Y / N):Y

When you have answered the final prompt, the printer will exit

Terminal Setup, reboot and start the selected application.

Selecting an Application

UBI Shell 4.0 Standard – Startup Manual

If you want to set up the printer or use any other of the facilities, you

should answer N (=No) to the “Select Application” prompt. The

following example illustrates how to change the printer's commu-

nication setup from 19,200 baud to 9,600 baud:

----------------

UBI SHELL

SEL. APPLICATION

----------------

(Y / N):N

----------------

UBI SHELL

SETUP

----------------

(Y / N):Y

----------------

SETUP FROM

TERMINAL

----------------

Reading printer setup, please wait.

If no change, press ENTER

To end terminal setup: enter QUIT (Q), or QUIT and SAVE (S)

CONTRAST,5

New value: (0-10) :

UART1,BAUDRATE,19200

New value: (1:300 2:600 3:1200 4:2400 5:4800 6:9600 7:19200) :6

Comment: You must specify the baudrate by a digit (1–7) according

to the displayed list of options and then press enter.

UART1,PARITY,NONE

New value: (1:NONE 2:EVEN 3:ODD 4:MARK 5:SPACE) :S

Comment: Enter Q to quit without saving, or S to save the new setup

and quit the Terminal Setup.

Are you sure? (Y / N):Y

Comment: As a safety measure, you must acknowledge your

command.

xf~xxff`xx~f`ffffffffffffffffffffxxxf`ff`ffffffffffffffffffffffffxx~fx

Comment: Since you have changed the communication para-

meters, the messages from the printer will become garbled. Reset

the communication setup in your terminal program according to

the printer's setup and press Enter.

Changing the Setup

TERMINAL SETUP, cont'd.

UBI Shell 4.0 Standard – Startup Manual

Exiting Terminal Setup

TERMINAL SETUP, cont'd.

To exit the Terminal Setup program, e.g. after having changed the

setup, you must select the Reboot option after having stepped

through all the facility options, as illustrated below:

----------------

UBI SHELL

PRINT SETUP

----------------

(Y / N):N

----------------

UBI SHELL

TESTFEED

----------------

(Y / N):N

----------------

UBI SHELL

TEST LABEL

----------------

(Y / N):N

----------------

UBI SHELL

SER-COM RESET

----------------

(Y / N):N

----------------

UBI SHELL

CLEAR RAM MEMORY

----------------

(Y / N):N

----------------

UBI SHELL

REBOOT

----------------

(Y / N):Y

If you answer N (=No) here, you will return to the “Select

Application” option, but if you answer Y (=Yes) the printer will

start up again and begin the UBI Shell countdown. Then you can

enter Terminal Setup once more by transmitting a triple T, enter the

UBI Shell manually by pressing the < Print > key with the print-

head down, or return to the last selected application by waiting for

the countdown to be completed without taking any action.

UBI Shell 4.0 Standard – Startup Manual

TERMINAL SETUP, cont'd.

Setup Parameters

The displayed values refer to the default

setup of a UBI EasyCoder 501 with one

communication port and 8 dots/mm print-

head density.

----------------

SETUP FROM

TERMINAL

----------------

Reading printer setup, please wait.

If no change, press ENTER

To end terminal setup: enter QUIT (Q), or QUIT and SAVE (S)

CONTRAST,5

New value: (0-10) :

UART1,BAUDRATE,9600

New value: (1:300 2:600 3:1200 4:2400 5:4800 6:9600 7:19200) :

UART1,PARITY,NONE

New value: (1:NONE 2:EVEN 3:ODD 4:MARK 5:SPACE) :

UART1,CHAR LENGTH,7

New value: (1:7 2:8) :

UART1,STOPBITS,2

New value: (1:1 2:2) :

UART1,FLOWCONTROL,RTS/CTS,DISABLE

New value: (1:ENABLE 2:DISABLE) :

UART1,FLOWCONTROL,ENQ/ACK,DISABLE

New value: (1:ENABLE 2:DISABLE) :

UART1,FLOWCONTROL,XON/XOFF,DATA FROM HOST,ENABLE

New value: (1:ENABLE 2:DISABLE) :

UART1,FLOWCONTROL,XON/XOFF,DATA TO HOST,ENABLE

New value: (1:ENABLE 2:DISABLE) :

UART1,NEW LINE,CR/LF

New value: (1:CR/LF 2:LF 3:CR) :

DETECTION,LSS ADJUST,80

New value: (0-127) Press F <CR> for testfeed. Press <CR> when OK :

DETECTION,FEEDADJ,STARTADJ,0

New value: (-9999 thru +9999) :

DETECTION,FEEDADJ,STOPADJ,0

New value: (-9999 thru +9999) :

MEDIA SIZE,XSTART,0

New value: (0-999) :

MEDIA SIZE,WIDTH,832

New value: (0-9999) :

MEDIA SIZE,LENGTH,1200

New value: (0-9999) :

MEDIA TYPE,LABEL (w GAPS)

New value: (1:LABEL (w GAPS) 2:TICKET (w MARK) 3:TICKET (w GAPS))

(4:FIX LENGTH STRIP 5:VAR LENGTH STRIP) :

PRINT DEFS,HEAD RESIST,519

New value: measured

PRINT DEFS,PAPER TYPE,UBI HP 20

New value:

0:RICOH 130LAB/LAM 1:KANZAKI 86S 2:UBI DT 110++ 3:UBI DT 110+

4:UBI DT 110 5:UBI DT 120 6:UBI GP 10 7:UBI GP 11

8:UBI HP 20 9:UBI HP 21 10:UBI HR 31 11:UBI HR 30

Select paper type, (0-11):

PRINT DEFS,NEW SUPPLIES

New value:

PERFORMANCE,NORMAL

New value: (1:NORMAL 2:HIGH 3:ULTRA HIGH) :

MEMORY ALLOC,IMAGE BUFF SIZE,48

New value: (0-9999) :

MEMORY ALLOC,REC BUF UART1,300

New value: (0-99999) :

MEMORY ALLOC,TRANS BUF UART1,300

New value: (0-99999) :

End of setup, enter QUIT (Q), or QUIT and SAVE (S)

Note:

After you have pressed CR, a series of additional

prompts will appear where you can adjust the LSS

following the same principles as described in the

chapter “Setup Mode”.

Page is loading ...

UBI EasyCoder 101 Startup Manual

Brand: UBI

Model: EasyCoder 101

Type: Startup Manual

This manual is also suitable for

UBI EasyCoder 101

Some of the key features of the UBI EasyCoder 101 include:

High-resolution printing: The EasyCoder 101 can print labels with a resolution of up to 300 dpi, ensuring that your labels are clear and easy to read.
Fast printing speed: The EasyCoder 101 can print labels at speeds of up to 4 inches per second, making it ideal for high-volume printing applications.

Download PDF

report

UBI EasyCoder 101 Startup Manual

This manual is also suitable for

UBI EasyCoder 101 Startup Manual

Related papers

Other documents