AMD K3780E User manual

K3780E Mainboard

I

K3780E

AMD 780E + AMD SB710

K3780E-S / K3780E-D (Type1)

K3780E-S Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

K3780E-S2 / K3780E-D2 (Type2)

K3780E-S2 Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D2 Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

User's Manual

Ver. 1.0

MB Dimension

170mm x 148mm

Operating System

Windows

®

XP/ Vista/ Win7

Release Date

091229

Mainboard

II

Things You Have To Know

0 The images and pictures in this manual are for reference only and may vary from the product

you received depending on specific hardware models, third party components and software

versions.

0 This mainboard contains very delicate IC chips. Always use a grounded wrist strap when

working with the system.

0 Do not touch any IC chip, lead, connector or other components.

0 Always unplug the AC power when you install or remove any device on the mainboard or

when configuring pins and switches.

Symbols

A

ttention- Important

Follow the procedures

Refer to other

Troubleshootin

g

Tips

Mainboard

III

Index

CHAPTER 1 GETTING STARTED........................................................................................... 1

1.1

INTRODUCTION ................................................................................................................ 1

1.2

SPECIFICATION ................................................................................................................ 2

1.2.1 CPU .................................................................................................................................. 2

1.2.2 Chipset.............................................................................................................................. 2

1.2.3 Memory ............................................................................................................................. 2

1.2.4 Audio - Realtek

®

ALC 662 ................................................................................................. 2

1.2.5 LAN - Realtek

®

RTL8111C................................................................................................ 3

1.2.6 Slot.................................................................................................................................... 3

1.2.7 Mini-IDE Connector........................................................................................................... 3

1.2.8 I/O Connectors.................................................................................................................. 3

1.2.9 Universal Serial Bus.......................................................................................................... 4

1.2.10 SATA II............................................................................................................................ 4

1.2.11 BIOS ............................................................................................................................... 4

1.2.12 Hardware Monitor............................................................................................................ 4

1.2.13 Power Supply.................................................................................................................. 4

1.3 CONFIGURATION .............................................................................................................. 5

1.3.1 Layout of System board + I/O Board Type 1 ..................................................................... 5

1.3.2 Layout of System board + I/O Board Type 2 ..................................................................... 6

1.4 HARDWARE INSTALLATION................................................................................................ 7

Jumpers ..................................................................................................................................... 7

Jumpers of System Board --- .....................................................................................................7

1.4.1 FPSWLED: Front Panel Headers...................................................................................... 7

1.4.2 JP1: Clear CMOS Jumper................................................................................................. 8

1.4.3 JU1: SPI Program Enable ................................................................................................. 8

Jumpers of I/O Board Type 1 --- ................................................................................................ 9

1.4.4 JP1: CF Card Master/ Slave Jumper................................................................................. 9

1.4.5 JP2: LVDS VDD POWER ................................................................................................. 9

1.4.6 CN1 - 6: RS-232 Voltage Setting ...................................................................................... 9

Jumpers of I/O Board Type 2 --- .............................................................................................. 10

1.4.7 JP1001: CF Card Master/ Slave Jumper......................................................................... 10

1.4.8 JP2001: LVDS VDD POWER ......................................................................................... 10

1.4.9 CN1/ CN2: RS-232 Voltage Setting ................................................................................ 10

Connectors............................................................................................................................... 11

Connectors of System Board ---............................................................................................... 11

1.4.10 J1 - J4: SATA................................................................................................................ 11

1.4.11 FAN1: FAN Header ....................................................................................................... 11

1.4.12 PWR1: ATX Power Connector ...................................................................................... 12

1.4.13 DDRII1/ DDRII2: Memory Installation............................................................................ 13

Connectors of I/O Board Type 1 ---.......................................................................................... 14

1.4.14 J3/ J4: PGIO ................................................................................................................. 14

1.4.15 J5: 4 Pin Power Conn. .................................................................................................. 14

1.4.16 USB1/ USB2: USB........................................................................................................ 14

Mainboard

IV

1.4.17 COM 1/ 2 & COM4~7: COM Port .................................................................................. 15

1.4.18 CON6: LVDS................................................................................................................. 15

1.4.19 U16: Print Port .............................................................................................................. 16

1.4.20 KBMS1: Mini-DIN PS/2 Port.......................................................................................... 16

1.4.21 USBLAN1/USBLAN2: LAN +USB Port ......................................................................... 16

1.4.22 VGA1: VGA Connector ................................................................................................. 17

1.4.23 HDMI............................................................................................................................. 17

1.4.24 SNDCN1 ....................................................................................................................... 17

1.4.25 MINI_PCI1: Mini PCI Slot.............................................................................................. 18

1.4.26 CON5: CF Card Connector ........................................................................................... 18

Connectors of I/O Board Type 2 ---.......................................................................................... 19

1.4.27 J2: 4 Pin Power Conn. .................................................................................................. 19

1.4.28 J4/ J5: PGIO ................................................................................................................. 19

1.4.29 USB1: USB ................................................................................................................... 19

1.4.30 USB2001/ USB2002: USB ............................................................................................ 19

1.4.31 COM 1/ 2: COM Port..................................................................................................... 20

1.4.32 CON1001: LVDS........................................................................................................... 20

1.4.33 C1001: D-SUB .............................................................................................................. 21

1.4.34 CON2: AUDIO1 - Line In/ Line Out/ Mic In.................................................................... 21

1.4.35 CON3: AUDIO2 - SURR/ LFE/ CNE/ SPDIF OUT ........................................................ 21

1.4.36 BIOSCN1: LPC Interface .............................................................................................. 22

1.4.37 KBMS1: Mini-DIN PS/2 Port.......................................................................................... 22

1.4.38 USBLAN1: LAN +USB Port........................................................................................... 22

1.4.39 HDMI1001..................................................................................................................... 23

1.4.40 DVI1001 ........................................................................................................................ 23

1.4.41 CON2005: CF Card Connector ..................................................................................... 23

CHAPTER 2 BIOS SETUP ..................................................................................................... 24

2.1

MAIN MENU ................................................................................................................... 24

2.1.1 Standard CMOS Features............................................................................................... 25

2.1.2 Advanced BIOS Features ............................................................................................... 26

2.1.3 Advanced Chipset Features............................................................................................ 27

2.1.4 Integrated Peripherals..................................................................................................... 28

2.1.5 Power Management Setup.............................................................................................. 29

2.1.6 PnP/PCI Configurations .................................................................................................. 30

2.1.7 PC Health Status............................................................................................................. 31

2.1.8 Load Fail-Safe Defaults...................................................................................................32

2.1.9 Load Optimized Defaults................................................................................................. 33

2.1.10 Set Supervisor Password.............................................................................................. 34

2.1.11 Set User Password ....................................................................................................... 35

2.1.12 Save & Exit Setup ......................................................................................................... 36

2.1.13 Exit Without Saving ....................................................................................................... 37

CHAPTER 3 SOFTWARE SETUP ......................................................................................... 38

3.1

SOFTWARE INSTALLATION .............................................................................................. 38

K3780E Mainboard

1

Chapter 1 Getting Started

1.1 Introduction

Thanks for choosing K3780E Mainboard. It is based on AMD 780E Northbridge chipset and AMD

SB710 Southbridge chipset. In addition, it also supports integrated AMD 780E Graphics Engine for

onboard graphics feature. It supports CPU as below:

K3780E-S / K3780E-D (Type1)

K3780E-S Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

K3780E-S2 / K3780E-D2 (Type2)

K3780E-S2 Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D2 Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

The K3780E provides 1 x Single channel SO-DIMM DDR2 800MHz by Single Core CPU up to 2GB;

2 x Dual channel SO-DIMM DDR2 800MHz by Dual Core CPU up to 4GB SO-DIMM.

This mainboard provides one MINI-IDE connector for MINI-IDE hard drives, supporting Ultra ATA

100/66/33MHz. and support 4 SATA II (300MB/s). In addition, PCI-E x16 Slot, Mini PCI & CF II

(optional) slot for use is also allowed.

The K3780E provides LVDS, HDMI, VGA (D-Sub) or DVI, 8 or 4 USB 2.0/ 1.1 and 6 or 2 RS232 ports

for use. There are maximal 8 USB2.0/ 1.1 ports which can be set up on this mainboard.

This mainboard also comes with one onboard 10/100/1000 Mbps Ethernet LAN chips (RTL8111C). On

the back panel of your case that you can directly plug into Internet cables.

The Realtek

®

ALC 662 AC’97 Codec supports high quality performance.

Mainboard

2

1.2 Specification

1.2.1 CPU

 K3780E-S / K3780E-D (Type1)

K3780E-S Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

 K3780E-S2 / K3780E-D2 (Type2)

K3780E-S2 Single Core CPU AMD Sempron 210U (1.5GHz)

K3780E-D2 Dual Core CPU AMD Athlon™ Neo X2 L325 (1.5GHz)

1.2.2 Chipset

 Northbridge Chipset - AMD 780E

 Southbridge Chipset - AMD SB710

 Super I/O Controller - W83627UHG

 IO RS-232 Controller - W83627UHG

 AC’97 Audio Codec - Realtek

®

ALC 662

 LAN Controller - PCI-E Realtek

®

RTL8111C

1.2.3 Memory

 1 or 2 DDR II SO-DIMM socket

 1 x Single channel SO-DIMM DDR2 800MHz by Single Core CPU up to 2GB

2 x Dual channel SO-DIMM DDR2 800MHz by Dual Core CPU up to 4GB

1.2.4 Audio - Realtek

®

ALC 662

 Compliant with AC’97 2.3 specification

 Support SPDIF output (cable by optional)

 Support 3D stereo enhancement

Mainboard

3

1.2.5 LAN - Realtek

®

RTL8111C

 PCI-E Realtek

®

Giga LAN Ethernet LAN

 RJ45 Connector with link/act and speed LED integrated

 K3780E I/O Board Type I: 2 x LAN

 K3780E I/O Board Type II: 1 x LAN

1.2.6 Slot

 K3780E I/O Board Type I

1 x PCI-E x16 Slot

1 x Mini-PCI Slot

1.2.7 Mini-IDE Connector

 One Mini-IDE Connector for two Mini-IDE 44pin hard disk drives

 CF card type I/II

 Ultra ATA 33/66/100 MHz

 High capacity hard disk drives

1.2.8 I/O Connectors

 One Mini-DIN PS/2 connector

 K3780E I/O Board Type I

1 x LVDS

1 x D-Sub

1 x HDMI

6 x COM header (6 ports by optional cable)

Realtek 6 Channel HD Audio

 K3780E I/O Board Type II

1 x LVDS

1 x DVI or D-Sub (D-Sub by optional cable)

1 x HDMI

2 x COM header (2 ports by optional cable)

Realtek 6 Channel HD Audio; Audio output header (by optional cable)

Mainboard

4

1.2.9 Universal Serial Bus

 K3780E I/O Board Type I: 8 x USB 2.0

2 x USB 2.0/1.1 header (4 ports by optional cable)

 K3780E I/O Board Type II: 4 x USB 2.0

1 x USB 2.0/1.1 header (2 ports by optional cable)

1.2.10 SATA II

 4 x SATA II (300MB/s)

 SATA RAID 0, 1, 10

1.2.11 BIOS

 Phoenix-Award™ BIOS

1.2.12 Hardware Monitor

 Monitor CPU temperature and FAN speed

 Monitor system voltages

1.2.13 Power Supply

 ATX 24 pin power

 1 x 5V/ 12V 4 pin power connector (K3780E I/O Board Type I)

Mainboard

5

1.3 Configuration

1.3.1 Layout of System board + I/O Board Type 1

Mainboard

6

1.3.2 Layout of System board + I/O Board Type 2

Mainboard

7

1.4 Hardware Installation

This section will assist you in quickly installing your system hardware. Wear a wrist ground strap

before handling components. Electrostatic discharge may damage the system's components.

Jumpers

Jumpers of System Board ---

1.4.1 FPSWLED: Front Panel Headers

Pin Assignment

LED

Pin Assignment

LED

1 HDD LED (+) 2 Power LED (+)

3 HDD LED (-)

Hard Drive LED

(HD_LED)

4 Power LED (-)

Power LED

(ACPI_LED)

5 Reset Control (+) 6 Power Switch (+)

7 Reset Control (-)

Reset Switch

(RST_SW)

8 Power Switch (-)

Power-on Switch

(PWR_SW)

9 N/A 10 N/C

 HD_LED (Hard Drive LED )

If your case front panel has a hard drive LED cable, attach it to this header. The LED will

flicker when there is hard disk drive activity.

 ACPI_LED (2 pin Power LED)

This header can be attached to the power LED cord from the case front panel onto this

header, then the power LED will illuminate while the system is powered on.

 RST_SW (Reset Switch)

This header can be attached to a momentary SPST switch (reset button) cable on your case

front panel. The switch is normally left open. When the switch closed, it will cause the

mainboard to reset and run the POST (Power-On Self Test).

 PWR_SW (Power-on Switch)

This header can be attached to a power switch cable on your case front panel. You can turn

your system on or off by pressing the button attached to this power switch cable.

Mainboard

8

1.4.2 JP1: Clear CMOS Jumper

The "Clear CMOS" function is used when you are unable boot your system and need to reset the

BIOS settings (CMOS settings) back to the manufacturer's original settings. This is also a way to

reset the system password if you have forgotten it.

JP3 Assignment

Pin 1-2 Closed

Normal (Default)

Pin 2-3 Closed

Clear CMOS Data

Note: "Closed" means putting a jumper cap onto two adjacent header pins.

1. Turn off your system and disconnect the AC power cable.

2. Set JP3 header to OFF (2-3 Closed).

3. Wait several seconds.

4. Set JP3 header to ON (1-2 closed).

5. Connect the AC power cable and turn on your system.

6. Reset your new password.

1.4.3 JU1: SPI Program Enable

This Jumper is to select the SPI Program device.

JP2

Assignment

Pin 1-2 Closed

Normal (Default)

Pin 2-3 Closed

EXT. PROGRAMMING

The following steps explain how to reset your CMOS

configurations when you forgot a system password.

Mainboard

9

Jumpers of I/O Board Type 1 ---

1.4.4 JP1: CF Card Master/ Slave Jumper

This Jumper is to select the CF works on Secondary Channel master device or Slave device.

JP2

Assignment

Pin 1-2 Closed

Slave

Pin 2-3 Closed

Master (Default)

1.4.5 JP2: LVDS VDD POWER

It’s for LVDS VDD power setting.

JP3

Assignment

Pin 1-2 Closed

VCC5V

Pin 2-3 Closed

VCC3P3V (Default)

1.4.6 CN1 - 6: RS-232 Voltage Setting

Pin Assignment Pin Assignment

1 RS232 2 VCC5V

3 RS232 4 RI (Default)

5 RS232 6 VCC12V

Mainboard

10

Jumpers of I/O Board Type 2 ---

1.4.7 JP1001: CF Card Master/ Slave Jumper

This Jumper is to select the CF works on Secondary Channel master device or Slave device.

JP2

Assignment

Pin 1-2 Closed

Slave

Pin 2-3 Closed

Master (Default)

1.4.8 JP2001: LVDS VDD POWER

It’s for LVDS VDD power setting.

JP3

Assignment

Pin 1-2 Closed

VCC5V

Pin 2-3 Closed

VCC3P3V (Default)

1.4.9 CN1/ CN2: RS-232 Voltage Setting

Pin Assignment Pin Assignment

1 RS232 2 VCC5V

3 RS232 4 RI (Default)

5 RS232 6 VCC12V

Mainboard

11

Connectors

Connectors of System Board ---

1.4.10 J1 - J4: SATA

Pin Assignment

1

GND

2

SATA_TX+

3

SATA_TX-

4

GND

5

SATA_RX+

6

SATA_RX-

7

GND

1.4.11 FAN1: FAN Header

There is one fan header available for cooling fan. This cooling fan plays an important role in

maintaining ambient temperatures in your system.

Assignment

1 GND

2 +12V

3 SENSER

Mainboard

12

1.4.12 PWR1: ATX Power Connector

This mainboard provides one ATX connector. You must attach it before the system is powered on.

This power connector supports several power management functions such as the instant

power-on function. The connector pins are described below.

Pin Assignment Pin Assignment

13 3.3V 1 3.3V

14 -12V 2 3.3V

15 COM 3 COM

16 PS-ON 4 +5V

17 COM 5 COM

18 COM 6 +5V

19 COM 7 COM

20 -5V 8 PWR-OK

21 +5V 9 5VSB

22 +5V 10 12V

23 +5V 11 12V

24 COM 12 3.3V

Mainboard

13

1.4.13 DDRII1/ DDRII2: Memory Installation

It provides DDR SO-DIMM socket which allows you to install 200-pin SO-DIMM.

Memory Installation Steps:

1. Match the notch on the bottom of the DIMM module with the corresponding pattern in the

DIMM slot. This will ensure that the module will be inserted with the proper orientation. Now

the chips or pins at the bottom of the DIMM module are still visible.

2. Lower the DIMM module into the DIMM Slot until the chips or pins at the bottom of the DIMM

module are hidden.

3. Press the DIMM module backward firmly using both thumbs until the module snaps into place.

Do not use excessive force.

4. Repeat steps 1, 2 & 3 for the remaining DIMM modules.

＊ The pictures above are for reference only. Your actual installation may vary

slightly from the pictures.。

Mainboard

14

Connectors of I/O Board Type 1 ---

1.4.14 J3/ J4: PGIO

Pin Assignment

1

FPGA_TDI

2

FPGA_TMS

3

INITB

4

GND

1.4.15 J5: 4 Pin Power Conn.

Pin Assignment

1

FPGA_TDI

2

FPGA_TMS

3

INITB

4

GND

1.4.16 USB1/ USB2: USB

These USB ports are used to attach with USB devices, such as keyboard, mouse and other USB

supported devices.

Pin Assignment Pin Assignment

1 +5V STB 2 +5V STB

3 USB- 4 USB-

5 USB+ 6 USB+

7 GND 8 GND

9 N/C 10 N/A

Mainboard

15

1.4.17 COM 1/ 2 & COM4~7: COM Port

This mainboard provides four COM pin headers for you to connect additional serial connectors on

your case back panel. Attach cables of serial connectors onto these headers, then you can use

the serial connectors connecting with a mic, modem or other peripheral device.

Pin Assignment Pin Assignment

1 DCD 2 SIN

3 SOUT 4 DTR

5 GND 6 DSR

7 RTS 8 CTS

9

+5V/RINGW/

+12V

10 N/C

1.4.18 CON6: LVDS

Pin Assignment Pin Assignment

2 12V 1 12V

4 GND 3 GND

6 3.3V/5V 5 3.3V/5V

8 GND/I2C_CLK 7 GND/ I2C_DATA

10

BCKLITE_ON

9

BRIGHTNESS

12

LVDS_GND

11

LVDS_GND

14

CHB_TX0+

13

CHA_TX0+

16

CHB_TX0-

15

CHA_TX0-

18

LVDS_GND

17

LVDS_GND

20

CHB_TX1+

19

CHA_TX1+

22

CHB_TX1-

21

CHA_TX1-

24

LVDS_GND

23

LVDS_GND

26

CHB_TX2+

25

CHA_TX2+

28

CHB_TX2-

27

CHA_TX2-

30

LVDS_GND

29

LVDS_GND

32

CHB_TXC+

31

CHA_TXC+

34

CHB_TXC-

33

CHA_TXC-

36

LVDS_GND

35

LVDS_GND

38

CHB_TX3+

37

CHA_TX3+

40

CHB_TX3-

39

CHA_TX3-

Mainboard

16

1.4.19 U16: Print Port

Pin Assignment Pin Assignment

1 RSTB- 2 RAFD-

3 RPDR0 4 ERR-

5 RPDR1 6 RIVIT-P-

7 RPDR2 8 KSLIN-

9 RPDR3 10 GND

11 RPDR4 12 GND

13 RPDR5 14 GND

15 RPDR6 16 GND

17 RPDR7 18 GND

19 ACK- 20 GND

21 BUSY 22 GND

23 PE 24 GND

25 SLCT 26 GND

1.4.20 KBMS1: Mini-DIN PS/2 Port

This mainboard provides a standard Mini-DIN PS/2 port to connect PS/2 keyboard and mouse.

Pin Assignment Pin Assignment

1

Keyboard/

Mouse data

2 N/C

3 GND 4 5V

5

Keyboard/

Mouse clock

6 GND

1.4.21 USBLAN1/USBLAN2: LAN +USB Port

There is one PCI-E Realtek

®

Giga Ethernet LAN port available for you to attach Internet cables.

These USB ports are used to attach with USB devices, such as keyboard, mouse and other USB

supported devices.

Page is loading ...

AMD K3780E User manual

This manual is also suitable for

AMD K3780E User manual

Other documents