Stenos SLD Installation Instructions
Stenos Linear Trimless Downlights
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATION (COVERED CEILING)
5. TYPE IC, INHERENTLY PROTECTED
6. AIRTIGHT PER ASTM E283
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.5
12052023
1 / 5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Stenos SLD Installation Instructions
Stenos Linear Trimless Downlights
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATION (COVERED CEILING)
5. TYPE IC, INHERENTLY PROTECTED
6. AIRTIGHT PER ASTM E283
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.5
12052023
2 / 5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Mounting Method 1A: Retrofit Install
1A Using appropriate hole saw or drywall cutter, drill/cut location for fixture. Fish the power lead wires from Power Supply through the cutout for easy access.
1A
Mounting Method 1B: New Construction Install (SLD-5 Shown)
1B
1B.1 Align the hanger bars on the plaster frame to the ceiling joists in desired
location. Fasten them to the joist by hammering in the tabs on the hanger
bars or with nails (supplied by others)
1B.3 Install the drywall to the joists. Mark fixture rough center from plumbline
mark on floor.
1B.2 Mark fixture center opening on floor with plumbline. Route the DC power
leads to the plaster frame Fitting Attachment holes with some slack to have
ready to connect to the downlight. Use provided wire clip to help retrieve
the wire during the next stages of installation. Make sure wires aren’t too
close to the fixture opening to avoid damaging wires in step 1B.4
1B.4 Create a cutout using a cutting tool.
*Note: The “Cutting Tool” aka RotoZip cutter will follow the hole in the Plaster
Frame as a guide to create the hole which keeps everything concentric*
SLD-3 SLD-5 SLD-12
4” 6” 12-5/8”
3-1/2”
Stenos SLD Installation Instructions
Stenos Linear Trimless Downlights
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATION (COVERED CEILING)
5. TYPE IC, INHERENTLY PROTECTED
6. AIRTIGHT PER ASTM E283
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.5
12052023
3 / 5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Junction Box Housing Install (OPTIONAL)
For Optional Junction Box Housing install, knock out desired box entry. Connect fitting
and supply cable Mount to Diecast Plaster Plate with supplied srews.
JB-XXL -CP
A B
C
Plaster Plate Install
2
2.3 A - Ensure fixture aperture mud plug is in place and tape perimeter.
B - First coating of fast curing compound, sand when dry. Then finish pass with drywall
compound, sand when dry.
C - Remove mud plug and Paint.
2.1 Use screw driver to raise drywall clamps before placing through hole. 2.2 Insert Plaster Plate into hole and secure to desired angle with clamping
screws. Clamp bracket will self rotate into position and stop at set angle,
continue screwing until the brackets compress the ceiling and plate.
2.4 Fish your DC feed from Power Supply. Connect the fixture
to the power leads using the 72” whip supplied on fixture.
Conductor Color Code:
Red = 24VDC Positive (+)
Black = Negative (-)
Red = Common 24VDC Positive (+)
Black = Warm White Negative (-)
White = Cool White Negative (-)
Static White
Dynamic White
Stenos SLD Installation Instructions
Stenos Linear Trimless Downlights
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATION (COVERED CEILING)
5. TYPE IC, INHERENTLY PROTECTED
6. AIRTIGHT PER ASTM E283
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.5
12052023
4 / 5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
3
Fixture Removal
Plaster Plate Install
2
2.5 Use of mudding tape suggested when plastering the fixture.
3.2 Slowly pull the fixture out using the two mini prybar tools.
3.1 Insert the two mini prybar tools included with the fixture into the two slots
on the inside of the fixture.
Stenos SLD Installation Instructions
Stenos Linear Trimless Downlights
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATION (COVERED CEILING)
5. TYPE IC, INHERENTLY PROTECTED
6. AIRTIGHT PER ASTM E283
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
REV0.5
12052023
5 / 5
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Accessory Install & Removal
4
4.1 Optional lens accessories can be simply snapped into the fixture LED bar
to secure. 4.2 If needed: Lens accessory can be removed by inserting the mini prybar
tool in between the endcap and the fixture head. Followed by a careful
gentle prying out of the accessory.
ASSEMBLED
POSITION
Aimming Fixture
5
5.1 If neccessary fixture head beam angle is adjustable. Carefully press on
the edge of the LED bar to either side to desired angle. Max rotation is ±
30°. .
5.2 Once desired angle is acheived it can be further secured but the set
screws on the endcaps.
CAUTION: Minimal tension of the set screw is required to
secure the bar.
+/— 30°
Tilt
+/— 30°
Tilt
-
1
-
2
-
3
-
4
-
5
luminii STENOS 3 inch Linear Trimless Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
luminii STENOS 5 inch Linear Trimless Installation guide
-
luminii SD-3 User manual
-
luminii Stenos User manual
-
-
-
-
-
-
-