INSTALLATION GUIDELINES
PAGE 1 OF 2 | UPDATED ON 5.31.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
Universal Metal Round 2 Leg Washstand
UNWS22 - 30” x 21” x 32 3/4”
UNWS28 - 28” x 19 15/16” x 31 1/2”
TECHNICAL DETAILS:
DETAIL
SPECIFICATION
ADJUSTABLE LEVELERS/FEET
YES
LEG MATERIAL
BRASS
RECOMMENDED ROUGH-IN SUPPLY HEIGHT
21” [534mm]
RECOMMENDED ROUGH-IN SUPPLY SPREAD
9” [229mm]
RECOMMENDED ROUGH-IN WASTE HEIGHT
19” [483mm]
STORAGE CAPACITY
None
TOP ATTACHMENT METHOD
Silicone
WEIGHT
16 LBS [7.25kg]
IMPORTANT:
➢ To ensure this product is installed properly, you must read and follow these guidelines.
➢ The owner/user of this product must keep this information for future reference.
➢ Install adequate blocking or position over a stud to properly secure the fixture.
➢ Inspect this product, upon receiving, to ensure it is the correct model and you have all parts
required for proper installation.
➢ Slab top, fittings, and lavatory sold separately.
➢ This product must be installed by a professional licensed contractor. Be sure your installation
conforms to all federal, state, and local codes.
➢ Take all necessary precautions to ensure that this product is protected during installation.
➢ Ensure the floor is level and the weight of this product will be adequately supported.
➢ The use of certain plumber’s putty may stain stone or tile surfaces.
X
Y
Z
X1
Y1
UNWS22
UNWS28
X
30"
28"
[762mm]
[711mm]
Y
21"
19 5/16"
[533mm]
[506mm]
Z
32 3/4"
31 1/2"
[832mm]
[800mm]
X1
26 3/4"
25 3/4"
[680mm]
[629mm]
Y1
19 3/8"
18 5/16"
[492mm]
[465mm]
PAGE 2 OF 2 | UPDATED ON 5.31.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
Universal Metal Round 2 Leg Washstand
UNWS22 - 30” x 21” x 32 3/4”
UNWS28 - 28” x 19 15/16” x 31 1/2”
Parts included; A - 1 x L/H Side Rail Assembly
B - 1 x R/H Side Rail Assembly
C - 1 x Horizonal Cross Rail
1. Place the parts on a protective sheet to avoid damaging any of the surface finishes during assembly.
2. Insert Horizontal Cross Rail (C) into the leg connections as shown (Orientation identified by Left & Right
Labels).
3. When fully inserted, rotate the Horizontal Cross Rail (C) to expose the pre-drilled fixing screw hole.
4. Insert the Fixing Screws (E) and fully tighten using a Screw Driver (DO NOT USE DRILL).
5. Secure both ends of the Horizontal Cross Rail (C) to the Leg Assemblies (A&B).
6. To measure and mark the positions for the Wall Screws (G), place the Wash Stand against the wall.
7. Place a Level on top of the Side Rail Legs and adjust the feet accordingly until it is level.
8. Mark the Vertical Center Line (for the Waste) and lines equally on either side for the Wash Stand Legs.
9. Using a pencil, mark the position of the Screw Holes.
10. Drill 6 x Holes in the Wall using a Ø7/32” Drill Bit - Push Anchors (F) into each hole.
11. Using the Wall Screws (G) - fix the Wall Plates securely to the wall using a Screw Driver (DO NOT USE DRILL).
12. MAKE ANY WATER CONNECTIONS AND FIX THE BASIN IN PLACE.
13. Final leg adjustments can be made to support the basin.
o
o
o
o
o
o
=
=
X1
D – Fixing Screw Pack
E – 2 x Fixing Screws
F – 6 x Anchors
G – 6 x Wall Screws
C
A
B
E
F
G
B
A
C
-
1
-
2
WaterWorks UNWS22 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WaterWorks PEWS01 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
American Standard Standard Washstand 9440.000 User manual
-
-
American Standard 9210.224.329 User manual
-
-
IKEA ENHET User manual
-
EZ-ACCESS P3G SLPS55 Operating instructions
-
EZ-ACCESS P3G SEM08 Installation guide
-
-
Bosch HBH4601 Installation guide
-
Pittsburgh Corning 117378 Operating instructions