INSTALLATION GUIDELINES
PAGE 1 OF 2 | UPDATED ON 2.24.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
STYLE No. CAMR01
Camden Metal Wall Mounted Rectangular Mirror
39 1/4” x 24” x 2“
TECHNICAL DETAILS:
DETAIL
SPECIFICATION
PRIMARY MATERIAL
Brass
WEIGHT
55lbs [25KG]
IMPORTANT:
➢ To ensure this product is installed properly, you must read and follow these guidelines.
➢ The owner/user of this product must keep this information for future reference.
➢ Install adequate blocking or position over a stud to properly secure the fixture.
➢ Inspect this product, upon receiving, to ensure it is the correct model and you have all
parts required for proper installation.
➢ This product must be installed by a professional licensed contractor. Be sure your
installation conforms to all federal, state, and local codes.
➢ Take all necessary precautions to ensure that this product is protected during
installation.
➢ Before drilling the wall check for electric cables and pipes. Never drill above or below
light switches or plug sockets.
Parts Included:
A. 1 x Main Mirror Assembly
B. 1 x Support Shelf
C. 1 x Wall Hanger
D. 8 x No. 8 2” Wall Screws
E. 8 x Red Wall Anchors
585mm [23”]
997mm
[39. ¼”]
38mm
[1. ½”]
51mm
[2”]
610mm [24”]
PAGE 2 OF 2 | UPDATED ON 2.24.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
STYLE No. CAMR01
Camden Metal Wall Mounted Rectangular Mirror
39 1/4” x 24” x 2“
Method of Installation
1. Using a tape measure, check the location where the mirror is to be installed. Be sure the
mirror will fit in the desired location.
2. Place a soft surface like a towel underneath the working area to avoid damage to
surfaces.
3. Mark with a pencil where the very bottom and center of the mirror need to be located.
4. Place the bottom of the Support Shelf on the wall and using a level to check that it is
straight then mark the screw locations though the holes.
5. Using a drill and 7/32” drill bit, pre-drill the holes for the wall anchors. Lightly tap the
wall anchors into place with a hammer.
6. Reposition the Support Shelf to the wall and secure with the screws provided. Check the
level again to determine that it is straight and horizontal. (Fig 1)
7. From the bottom holes of the Support Shelf measure up 36 3/8” and mark this spot for
the bottom of the Wall Hanger. Alternatively mark 2 1/8” from the top of the mirror.
8. Place the Wall Hanger on to wall and proceed to mark through the holes checking it is
straight with a level. Then secure the Wall Hanger with the screws provided. (Fig 2)
9. Carefully place the mirror onto the installed Wall Hanger (two people recommended).
The mirror should sit on the Support Shelf before bottoming out on the Wall Hanger
providing the correct support for the mirror.
10. The mirror can then be adjusted side to side by gently sliding the mirror along the Wall
Hanger to ensure the mirror is centered. (Fig 3)
Wall Hanger
Support Shelf
Fig 1
Fig 3
Fig 2
Tools needed:
Pencil, tape measure, spirit level and screwdriver or a standard drill.
Please note the below instructions and fixings provided are for a masonry wall. If you are
installing to a plasterboard wall, partition, or any other wall, we recommend a timber battens or
frame behind the wall for support as well as source any special screws or fixings needed.
54mm
[2. 1/8”]
19mm
[3/4”]
924mm
[36. 3/8”]
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WaterWorks HNSF24 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
SimplyNeu SNBR-BC User manual
-
Hygena Bergen 2 Door Small Sliding Wardrobe User manual
-
-
Kenroy Home 60351 Operating instructions
-
-
EPOWP D0102HPR8AWXYL Installation guide
-
USE 1050.13 Operating instructions
-
Thermogroup RR7070GT Installation guide
-
Roswell 803036R-LED-AC Installation guide
-
Style Selections 1678VM-49-292 Installation guide
