Rhino-Rack Vortex RCH 2 Bar Roof Rack Installation guide

Brand
Rhino-Rack
Model
Vortex RCH 2 Bar Roof Rack
Type
Installation guide
RCL, RCH 2,4,6 Kits
Important: Please read these instructions carefully prior to installation.
Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the
correct location.
Check the contents of kit before commencing fi tment and report any discrepancies.
Place these instructions in the vehicle’s glove box after installation is complete.
Important Information
Maximum load carrying capacity: 100kg / 220lbs
Maximum carrying capacity: Up to 100kg (220lbs) including the weight of the rack system.
Please refer to your vehicle manufacturers handbook for maximum carrying capacity. Always use the lower of the two fi gures. Load must be evenly
distributed over the entire basket.
Warning: Do not attempt to fi t the rack system to your vehicle unless you fully understand these fi tting instructions. Please direct any questions
regarding fi tting to the dealer from where the roof racks were purchased.
Use only non-stretch fastening ropes or straps.
Recommendations: It is essential that all bolt connections be checked after driving a short distance when you fi rst install your roof racks. Bolt
connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances
travelled). You should also check the roof racks each time they are re-fi tted. Always make sure to fasten your load securely. Please also ensure
that all loads are evenly distributed and that the centre of gravity is kept as low as possible and must be entirely contained within the extents of the
roof racks. Rack System must be removed when putting vehicle through an automatic car wash.
Caution: The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we recommend you
exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking.
Off-road use:
The Roof Rack System may be used in off road applications, however a safety factor of 1.5 is enforced. That is, maximum permissible off road load
is 66kg (145lbs). Although the crossbars are tested and approved to AS1235-2000/ 15011154, off-road conditions can be much more rigorous.
Extreme car must be taken in off road conditions
Note for Dealers and Fitters:
It is your responsibility to ensure these fi tting instructions are given to the end user or client.
Rhino-Rack 3 Pike Street, Rydalmere,
NSW 2116, Australia. Document No: R1182 Fit Time: 15min per Bar
(Ph) (02) 9638 4744 Prepared By: Kayle Everett Issue No: 03
(Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 28/03/2017
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
1. Check Part No./Kit is correct 3. Fit roof rack accessory
2. Read through instruction before installing 4. Check and recheck all fasteners are secure
Page 1 of 5
Note: Be sure to check Rhino-Rack website to see if you have
the latest version of instructions before beginning installation.
CONTROLLED
Page 2 of 5
RCL, RCH 2,4,6 Kits
When these roof racks are to be used
on a vehicle that is driven off sealed
roads, the manufacturer maximum
roof load rating (to be found in the
vehicles User Manual) should be
divided by 1.5. Do not forget to
subtract the complete crossbar system
weight from your maximum carrying
capacity.
!
!
!
km/h X
100kg/220lbs
(Urban Road) 66kg/145lbs
(Off Road)
=
Ensure Ladder is well
supported on the ground
to help support tent. Take
extreme caution when
climbing heights above
1.2m/4ft.
!
WARNING! Important Load Carrying Instructions
With utility vehicles, the cabin and the canopy move
independently. Roofracks and vehicle can be damaged if the
item transported is rigidly fi xed at points on both the cabin and
canopy. Instead, rigidly fi x to either the cabin roofracks or the
canopy roofracks. YES
Paddle/ Surfboards should be fi xed to the front of the
vehicle.
It is required for
Clam Shell Roof
Top Tents to use a 3
Crossbar System.
!
Page 3 of 5
RCL, RCH 2,4,6 Kits
Tools Required:
Allen Key (provided).
Metal Key (provided).
Notes:
Crossbars and Fit Kits are sold as separate
and are required for individual vehicle fi ts.
Heavy Duty Bars will require a QMHD05 kit.
1.
2.
4.
5.
6.
7.
8.
9.
10.
11.
Item RCL 2 Kit
Qty 4 Kit
Qty 6 Kit
Qty Part No.
1 Locking Leg Cover (37mm) 2 4 6 M810
2 Locking Leg Base (37mm) 2 4 6 M813
3 Key Barrel 2 4 6 CA1339
4 Key 1 2 2 -
5 Allen Key 1 1 1 H034
6 M6 x 20mm Socket Head Screw 2 4 6 B054
7 M6 Spring Washer 2 4 6 W004
8 M6 x 16mm Flat Washer 2 4 6 W031
9 M6 Nut 30mm x 25mm 2 4 6 N035A
10 Instructions 1 1 1 R1182
Item RCH 2 Kit
Qty 4 Kit
Qty 6 Kit
Qty Part No.
10 Locking Leg Cover (52mm) 2 4 6 M812
11 Locking Leg (52mm) 2 4 6 M811
3 Key Barrel 2 4 6 CA1339
4 Key 1 2 2 -
5 Allen Key 1 1 1 H021
6 M6 x 20mm Socket Head Screw 2 4 6 B054
7 M6 Spring Washer 2 4 6 W004
8 M6 x 16mm Flat Washer 2 4 6 W031
9 M6 Nut 30mm x 25mm 2 4 6 N035A
10 Instructions 1 1 1 R1182
Parts List
3.
Instructions
Use the Metal Key provided to unlock the Cover Plate and remove. Remove the Allen Key from its storage
position.
1
Closed Open
Front View:
2Insert the M6 hardware as
shown. Finger tighten only
at this stage. M6 Nut 30mm x 25mm
M6 x 20mm
Socket Screw
M6 Spring Washer
M6 x 16mm Flat
Washer
Note: Low
Leg used
throughout
instructions.
RCL 37mm RCH 52mm
Page 4 of 5
RCL, RCH 2,4,6 Kits
Slide the Assembled legs into the Crossbars as
shown. Insert Vortex Rubber, cut to length as
required.
3
Spring washer.
4Fix the Crossbars to the vehicle specifi c Base
Kit that has been purchased, using the Allen Key
provided.
5Ensure the Crossbars have an equal overhang. Tighten the M6 Leg Hardware with the Allen Key provided.
Insert the Underbar Strips into the slots either side
of the installed Leg. Cut to length as required.
6 7 Insert the Crossbar End Caps and lock in place.
Replace the Allen Key and Leg Cover. Lock the
Leg Cover Plate with the key provided. Be sure all
fi xtures are secure before use.
(=) (=)
M6 Caps Screws
Flat washer.
Note: Images are example only. RCL/RCH legs can be
fi t to either tracks or pads. Pads and track fi t kits are
sold as separate.
Note: In some installations
it may be required to fi t the
leg to the base fi rst due to
the length of screw on RCL
(low) leg.
Page 5 of 5
RCL, RCH 2,4,6 Kits
Note To fi t Legs to Heavy Duty Crossbars,
Pioneer Trays and Platforms
Pioneer QMHD05 must be purchased as
separate. Install the Spacer Kit then
the HD Crossbars.
M6 Channel Nut
Quick Mount Leg
HD Bar Spacer
M6x30 Socket
HD Cap Screw
M6 Channel Nut
Pioneer Leg
Height Spacer
M6x35 Socket
HD Cap Screw
To fi t Legs to Pioneer Trays/ Platforms, positioned wide
on vehicle, QMPS10 must be purchased as separate.
Install the Spacer Kit then the Tray/ Platform.
End Cap
Heavy Duty
Crossbar
Rubber Strip
Check all fi xtures are secure before use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Rhino-Rack Vortex RCH 2 Bar Roof Rack Installation guide

Brand
Rhino-Rack
Model
Vortex RCH 2 Bar Roof Rack
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents